ApplyLabWork MPT-SP001PK MSLA Spring Pink Instructions
- June 3, 2024
- APPLYLABWORK
Table of Contents
ApplyLabWork MPT-SP001PK MSLA Spring Pink
Check
- Resin tank and LCD screen are clean
- Shake resin bottle well before use
- Tank and plateform are properly fastened
Printer Settings Recommendation
Brand| Model| Layer height
(mm)
| Bottom Layer
counts
| Exposure time
(s)
| Bottom Exposure
(s)
| Lifting Speed
(mm/min)
| Lifting Distance
(mm)
| Retract Speed
(mm/min)
---|---|---|---|---|---|---|---|---
Phrozen| Sonic| 0.1| 6| 4| 30| 60| 8| 120
Sonic mini| 0.1| 6| 5.5| 30| 60| 8| 120
Sonic Mighty 4 K| 0.1| 10| 4| 60| 60| 8| 120
Elegoo| Mars2 Pro| 0.1| 6| 3.6| 30| 60| 8| 120
Mars3| 0.1| 6| 3.6| 30| 60| 8| 120
| | Layer height
(mm)
| Bottom Layer
counts
| Exposure time
(s)
| Bottom Exposure
(s)
| Lifting Speed
(mm/s)
| Lifting Distance
(mm)
| Retract Speed
(mm/s)
Anycubic| MonoX| 0.1| 6| 2.2| 30| 1| 8| 2
- Light-off Delay = 15s under current lift-retract motion. [ When printing large object, increase Lifting Distance and recalculate Light-off Delay ]
- For Sonic Mighty 4K, please set Transition Layer Count to 20
- Light intensity varies each printer. Please adjust exposure time ±0.1~0.5 second and/or XY dimesion ratio according to printing result and part application.
Parts Recommendation
- Avoid large aspect-ratio geometry (e.g. thin wall or long thin rod) in the sturcture to reduce failures.
- If support is needed, please set contact diameter>1.2(mm), and density>60%
Washing
Wipe off excess resin on printed parts with paper towel, submerge into 95% IPA and place the container in ultrasonic bath, wash for 5 minutes. Replace by clean IPA and repeat ultrasonic washing for another 5 mintes (total 10 minutes). Blow off all excess IPA and set parts in a shaded, ventilated place to dry at least 2 hours before curing. Dried print will be tacky to touch
Post-curing (Mandatory)
Submerge the parts into glycerol/glycerin(CAS # 56-81-5) and start FormCure with 60 ℃ / 30 mins setting. Wash off glycerol in water and dry off with paper towel.
- If prints don’t sink completely into glycerol, add water (no more than half of volume) to adjust liquid density.
- If prints are still tacky to touch after post-curing, rinse with acetone (CAS # 67-64-1) for no more than 1 minute will significantly reduce tackiness
Storage
- Keep resin away from heat and light.
- NOT accessible to children
Note:
- Keep printing environment well ventilated.
- Wear gloves when handling Spring resin and avoid direct contact.
- Vibration of the parts during printing process might cause resin splash onto printer ’s cover. Use paper towel and IPA to clean immediately.
- Slight pigment settlement is normal.Gentally mix remaining resin in resin tank with rubber spetula for color evenness.
- Don’t leave the parts on building platform after printing for more than one day.
- Color of printed parts will gradually turn yellow if contiuously receive photon energy.
- Spring resin should NOT use with food, drink, or on/in the human body unless specifically indicated.
Prototype Engineering Series
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>