GT Omega ART Simulator Cockpit Installation Guide
- August 17, 2024
- GT Omega
Table of Contents
GT Omega ART Simulator Cockpit
Specifications
- Recommended Assembly: 1-2 People
- Read Instructions Time: 10 Minutes
- Assembly Time: 30 Minutes
- Load Capacity: Up to 200KG
Product Usage Instructions
What’s in the Box
- A. 6x M6x40 Bolts
- B. 6x Hand Screws
- C. 8x Rubber Feet
- D. 2x M8x80 Half-Threaded Bolts
- E. 8x M8x16 Hex Bolts
- F. 1x Metal Spacer
- G. 14x Washers
- H. 8x M8x35 Bolts
- I. 4x Flange Nuts
- J. 2x Allen Keys
- K. 1x Spanner
- L. 4x Velcro Straps
- M. 2x M6x16 Bolts
- N. 8x M8 Nuts
- O. 6x M8 Square Nuts
Assembly Instructions
-
Assemble Front Section:
4x (H), 4x (G), 4x (N), 2x (B), 6x (A)
Insert the wheel deck supports into the front frame and bolt the wheel deck into position.
Line up the Pedal Tray and bolt it into place. -
Assemble Rear Section:
4x (E), 4x (O)
Connect lower seat mount sections to the rear frame, keeping them loosely fitted for adjustment. -
Mount Racing Seat:
4x (H), 4x (G), 4x (I)
Pull the seat lever to extend the seat rails and bolt the upper sections of the seat mount to the rails. -
Connect Front and Rear Sections:
4x (B)
Use extension bars to connect the front and rear sections, then secure using hand screw bolts provided.
Assembly Guide
- Recommended 1-2 People
- Read Instructions 10 Minutes
- Assembly Time 30 Minutes
WARNING
- Children should not use unsupervised
- Do not exceed load capacity of 200KG
- Do not stand on the Cockpit
- Take care when assembling
- Do not Push or pull Cockpit across the floor
FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY, SAFETY, AND OPERATION INSTRUCTIONS REGARDING THE USE OF THIS PRODUCT MAY RESULT IN PROPERTY DAMAGE OR BODILY INJURY.
- This document contains important safety regulations. Any non-conforming use may result in personal injury or mechanical damage.
- Please read this user manual carefully before use as it provides key information about safety, use, and assembly of the ART Cockpit.
- Ensure that you have received all parts according to the part checklist prior to installation. If any parts are missing or faulty, contact the GT Omega support team for replacements.
- Do not over tighten the screws during installation.
- This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
- This product is designed for indoor use only. Using the product outdoors could lead to product failure and personal injury.
- Alteration or modification of any factory components outlined in the checklist will automatically void your warranty.
- Place the ART Cockpit away from corrosive gas, water and dusty environments.
The ART Cockpit is designed for indoor use and dry work areas only. Under no circumstances does the manufacturer accept warranty claims or liability claims for damages caused from improper use or handling.
WHAT’S IN THE BOX
ASSEMBLY INSTRUCTIONS
-
Assemble Front Section Insert the wheel deck supports into the front frame as shown then bolt the wheel deck into position.
Line up the Pedal Tray and bolt into place. -
Assemble Rear Section Connect lower seat mount sections to rear frame. Keep loosely fitted to allow for easy adjustment when mounting seat.
-
Mount Racing Seat Pull the seat lever to allow you to extend
Bolt the upper sections of the seat mount to the seat rails. Adjust rails as needed to access rear bolt holes. Connect the upper and lower sections of your seat mount. Once fitted, centre the seat and mounts then tighten all the nuts and bolts.
TIP : Installation guide is for GT Omega racing seats. If you are using something else the process may be different. -
Connect Front and Rear Sections Using a set of the extension bars, connect the front and rear sections and then secure using the hand screw bolts provided.
Longer extension bars are better for users with longer legs. It’s easy to swap out the sets to adjust for users of different sizes!
NOTE : Avoid over-tightening screws. As this may damage the product. -
Connect Gear Shifter Mount Connect the gear shifter mount as shown.
TOOLS : The gear shifter mount can be mounted further back or on the left or ride side to suit your preference. Bolt the gear shifter plate firmly into place. -
Connect Feet to Cockpit Carefully turn the cockpit the cockpit on its side and screw in the feet.
TOOLS : The ART Cockpit feet are adjustable in height making them able to provide a stable experience on uneven floors.
ADJUSTMENT GUIDE
- Loosen hand screws on both sides to change wheel deck height.
- Loosen bolts on the wheel deck to adjust wheel deck angle.
- Loosen hand screws on both sides to adjust pedal plate angle.
Unlock the full potential of your art cockpot
ART Single Monitor Mount Practical and convenient: This essential upgrade completes your ART Cockpit and is fully adjustable to suit your needs!
To see these products and more, visit us at gtomega.eu
Need Help?
We’re here for you! Contact our support team:
Supporteu@gtomega.com Handling times targeted
at 24 hours. Please allow time for a response (+44)141-370-6780 Monday –
Friday 9am – 4pm (Glasgow, Scotland)
FAQ’S
Q: Can children use the product unsupervised?
A: No, children should not use the product unsupervised for safety reasons.
Q: What is the load capacity of the product?
A: The load capacity of the product is up to 200KG.
Q: Can the product be used outdoors?
A: The ART Cockpit is designed for indoor use and dry work areas only.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>