ApplyLabWork MSP-C001CN MSLA Castable Cyan User Manual
- June 3, 2024
- APPLYLABWORK
Table of Contents
ApplyLabWork MSP-C001CN MSLA Castable Cyan
Check
- Vat and LCD screen are clean
- Shake well (60 sec) before pouring
- Vat and platform are tightened properly
Printer Setting Recommendation Chart
(select 50um layer thickness for fine structure)
Printer
| Layer Thickness (μm)| Bottom (Burn-In) Layers| Normal Layer Exposure Time (s)| Bottom Layer Exposure Time (s)|
Light-off Delay (s)
| Lifting Distance (mm)| Lifting Speed (mm/min)| Retract Speed (mm/min)
---|---|---|---|---|---|---|---|---
Shuffle| 50| 6| 12| 40| 10| 6| 60| 150
Shuffle XL| 50| 6| 12| 40| 15| 8| 60| 150
Sonic| 50| 6| 2.5| 7| 10| 6| 60| 150
Sonic Mini| 50| 6| 5| 15| 10| 6| 60| 150
Sonic Mighty 4K|
50
|
6
|
3.5
|
12
|
15
|
8
|
60
|
150
Elegoo Mars2 Pro|
50
|
6
|
3
|
15
|
9
|
5
|
60
|
150
Elegoo Mars3 Ultra 4K|
50
|
6
|
2.5
|
12
|
9
|
5
|
60
|
150
MiiCraft| 50| 6| 1.2| 4| –| –| Slow| Slow
Prusa SL1| 50| 6| 12| 40| –| –| 5 (tilt time)| –
Anycubic Photon MonoX| 50| 6| 2| 15| 15| 8| 1 (mm/s)| 2.5 (mm/s)
Each printer is unique, light intensity varies from printer to printer even
though they are the same model and make. Please adjust normal exposure time
from our recommended settings 2 ( 0.5 for Mono LCD) seconds for your
printer and print geometry.
For size calibration, download the stl file:
https://www.thingiverse.com/thing:1586206
Washing
Fresh IPA rinse (95+% concentration) over prints. Do NOT submerge prints in IPA. Blow dry via compressor air immediately after rinse and set print in a shaded airy place to fully dry before casting (approx 60 mins). Limit IPA contact time to 30 seconds as prolong contact time could cause print deformation. Color migration (leaking color from prints) of prints are normal.
No Post-Curing Needed
Storage
- Store resin bottle out of direct sunlight.
- Do Not store resin in the vat for more than 2 days when not in use.
- Filter out all debris in case of failed prints.
Note: Slight pigment settlement is normal. Gently mix remaining resin in resin vat with soft wiper for color evenness.
Product Features
- ApplyLabs Castable Cyan offers high quality, dimensionally accurate 3D Prints and straightforward easy Casting for the Jewellery and
- Dental Industry.
- Main features include:
- Low shrinkage (Storage at 25℃ for 1 week, <1 vol%)
- Low ash
- Low expansion during burnout
- No need for UV post-curing
- No need for dip or spray
Casting instruction
- For optimal results, please use investment designs for casting 3D printed resins. Example: R&R Plasticast, Optima Prestige, Gold Star Resincast or equivalent.
- Consider using ‘Sticky Wax’ when attached models to wax, as adhesion between resin and wax is not always very strong. Or consider printing casting sprues in place when appropriate.
Burnout Schedule
Follow the burnout schedule of your investment manufacturer, or the schedule we recommend below and make modifications according to your burnout equipment. Example: Burnout cycle for a 4”x6” vacuum flask using R&R Plasticast mixed at 40:100 ratio.
- Start kiln at room temperature or preheated to 150°C (300°F)
- Hold 150°C (300°F) for 3 hours
- Raise temperature to 370°C (700°F) over 2 hours.
- Hold 370°C (700°F) for 2 hours
- Raise temperature to 730°C (1350°F) over 2 hours
- Hold 730°C (1350°F) for 2 hours (for large flask, let sit for 1-2 hours longer)
- Reduce to casting temperature (for example, 430°C (800°F) for sterling silver)
- Hold Casting Temperature for 2 hours
- Note: Do Not Exceed Maximum Temperature
Gallery
This project cast in Silicon Bronze using a standard wax burnout schedule with R&R Plasticast 40:100 using an Electric Melter and Kaya Vacuum Casting Machine.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>