SRPC 70260021-A 200W ZigBee LED Driver Instruction Manual

SRPC 70260021-A 200W ZigBee LED Driver

Product Specifications

• Product Name: 200W ZigBee LED Driver (Constant Voltage)
• Input Voltage: AC 100-277V
• Output Voltage: 24VDC
• Max. Power Output: 200W
• Dimming Range: 0.1% – 100%
• Control Method: ZigBee
• Working Temperature: -20°C to +45°C
• Working Humidity: 10% to 95% RH non-condensing

Product Usage Instructions

Function Introduction:
The LED driver allows for dimming and control of LED lighting. The program key can be used to switch on/off the load and adjust light intensity.

Wiring Instructions:

1. Ensure correct wiring according to the provided connection diagram.

ZigBee Network Pairing:

1. Remove the device from any previous ZigBee network to avoid pairing issues.
2. Using a ZigBee Controller or hub interface, select to add a lighting device and follow the pairing instructions provided.

Dimming Control:
The dimming range of the driver is from 0.1% to 100%. Dimming is achieved through Pulse Width Modulation control method.

Safety & Warnings:

1. Follow all safety standards and regulations during installation and use.
2. This ZigBee device operates as a wireless receiver and must communicate with ZigBee compatible systems only.

Frequently Asked Questions (FAQ):

Q: How do I reset the LED driver for ZigBee network pairing?
A: To reset the device for ZigBee network pairing, follow these steps:

1. If the device was previously connected to a ZigBee network, remove it from that network.
2. Proceed to pair the device with a new ZigBee network using the ZigBee Controller or hub interface.

Important: Read All Instructions Prior to Installation

Function introduction

Note:

1. W channel can be turned on through Gateway’s color temperature control interface which will mix RGB channels as 1 channel white and then make color tuning with the 4th channel white. Once turned on, the brightness of white channel will be controlled together with RGB channels.
2. W channel can be controlled separately from RGB channels through RGBW zigbee remote or touch panel’s W button, please refer to their manuals.

Product Data

Output

| LED Channel| 4
---|---|---
DC Voltage| 12V DC| 24V DC
Max. Current| Max. 8.3A/ch, ch1+ch2+ch3+ch4=16.6A| Max. 4.1A/ch, ch1+ch2+ch3+ch4=8.4A
Voltage Tolerance| ±1%
Rated Power| max. 200W

Input

| Voltage Range| 100-277V AC
Frequency Range| 50/60Hz
Power Factor (Typ.)| > 0.98 @ 230VAC
Total Harmonic Distortion| THD ≤ 15% (@ full load / 230VAC)
Efficiency (Typ.)| 93% @ 230VAC full load
AC Current (Typ.)| 2.3A @ 100VAC, 1A @ 230VAC, 0.9A@277VAC
Inrush Current (Typ.)| Cold Start Max. 65A @ 230VAC
Leakage Current| < 0.5mA /230VAC
Standby Power

Consumption

| < 1W

Control

| Dimming Interface| ZigBee
---|---|---
Dimming Range| 0.1%-100%
Dimming Method| Pulse Width Modulation

Protection

| Over Current| Yes, recovers automatically after fault condition is removed
Over Temperature| Yes, recovers automatically after fault condition is removed

Environment

| Working Temp.| -20℃ ~ +45℃
Max. Case Temp.| 85℃ (Ta=”45℃”)
Working Humidity| 10% ~ 95% RH non-condensing
Storage Temp. & Humidity| -40℃ ~ +80℃, 10% ~ 95% RH

Safety & EMC

| Safety Standards| UL8750, CAN/CSA C22.2 No. 250.13-14, ENEC EN61347-1, EN61347-2-13 approved
Withstand Voltage| I/P-O/P: 3.75KVAC
Isolation Resistance| I/P-O/P: 100M Ohms / 500VDC / 25℃ / 70% RH
EMC Emission| EN55015,  EN61000-3-2,  EN61000-3-3
EMC Immunity| EN61547, EN61000-4-2,3,4,5,6,8,11, surge immunity Line-Line 1KV

Others

|

MTBF

| 187100H, MIL-HDBK-217F @ 230VAC at full load and 25℃ ambient temperature

• Dimmable LED driver with metal case, 4 channels 12/24VDC constant voltage output
• Class 1 power supply, full isolated metal case
• Built-in two-stage active PFC function, PF > 0.98, Efficiency > 93%, low standby power < 1W
• Compliant with Safety Extra Low Voltage standard
• Over load, over temperature protection
• ZigBee RGBW LED light device based on ZigBee 3.0 protocol, supports Touchlink commissioning
• Enables to control ON/OFF, light intensity and RGB color
• W channel can be controlled through Gateway’s color temperature control interface
• W channel can be controlled separately from RGB channels through RGBW zigbee remote or touch panel’s W button
• Can directly pair to a compatible ZigBee remote via Touchlink
• Supports zigbee green power and can bind max. 20 zigbee green power remotes
• Compatible with universal ZigBee coordinator or gateway products
• IP20 rating, suitable for indoor LED lighting applications
• 5 years warranty

Safety & Warnings

• DO NOT install with power applied to the device.
• DO NOT expose the device to moisture.

Operation

1. Do wiring according to connection diagram correctly.

2. This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible systems. This receiver receives and is controlled by wireless radio signals from the compatible ZigBee system.

3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)
   Step 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing will fail. Please refer to the part “Factory Reset Manually”.
   Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as instructed by the controller.

4. TouchLink to a Zigbee Remote

Note:

1. Directly TouchLink (both not added to a ZigBee network), each device can link with 1 remote.
2. TouchLink after both added to a ZigBee network, each device can link with max. 30 remotes.
3. For Third-Party Automation Devices, add remote and device to network first then TouchLink.
4. After TouchLink, the device can be controlled by the linked remotes.

Removed from a Zigbee Network through Coordinator or Hub Interface

Factory Reset Manually

Note: All configuration parameters will be reset after the device is reset or removed from the network.

Factory Reset through a Zigbee Remote (Touch Reset)

Note: Make sure the device already added to a network, the remote added to the same one or not added to any network.

Find and Bind Mode

Learning to a Zigbee Green Power Remote

Delete Learning to a Zigbee Green Power Remote

Setup a Zigbee Network & Add Other Devices to the Network (No Coordinator Required)

Step 2: Set another device or remote or touch panel into network pairing mode and pair to the network, refer to their manuals.

Step 3: Pair more devices and remotes to the network as you would like, refer to their manuals.

Step 4: Bind the added devices and remotes through Touchlink so that the devices can be controlled by the remotes, refer to their manuals.

Note:

1. Each added device can link and be controlled by max. 30 added remotes.
2. Each added remote can link and control max. 30 added devices.

ZigBee Clusters the device supports are as follows:

Input Clusters

• 0x0000: Basic
• 0x0003: Identify
• 0x0004: Groups
• 0x0005: Scenes
• 0x0006: On/off
• 0x0008: Level Control
• 0x0300: Color Control
• 0x0b05: Diagnostics

Output Clusters

• 0x0019: OTA

OTA
The device supports firmware updating through OTA, and will acquire new firmware from zigbee controller or hub every 10 minutes automatically.

Wiring diagram

Product Dimension

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>