ApplylabWork MD-R002CR Laser Modeling Clear V2 Instruction Manual
- May 15, 2024
- APPLYLABWORK
Table of Contents
ApplylabWork MD-R002CR Laser Modeling Clear V2
Product Information
Specifications
- Product Name: Laser Modeling Clear V2 (MD-R002CR)
- Compatible with: Form 3 Series Printers
- Resin Type: Clear V2
- Recommended Cleaning Solution: IPA 95% or higher, FormWash, or ultrasonic cleaner
- Post-Curing Options: FormCure 35 for 15 mins, FormCure 60 for 30 mins
Product Usage Instructions
Refilling Resin Cartridge
- Refill Clear V2 resin into Clear-V4 cartridge.
- Open the air vent on the cartridge and turn it upside down.
- Drip dry through the air vent for at least 5 minutes to minimize cross-contamination.
- Refill the cartridge, shake well, and insert it into the printer for printing.
Washing Process
- Clean the printed model with IPA 95% or higher, FormWash, or an ultrasonic cleaner for 5 minutes.
- After washing, shake off or blow off residual IPA from the model.
- Allow the paint to dry for 60 minutes in a shaded and ventilated area before UV post-curing. (The dried print might be slightly tacky to the touch.)
Post-Curing Instructions
For optimal transparency, you can skip post-curing. However, follow these steps for specific needs:
- To minimize yellowing: Use FormCure 35 for 15 minutes.
- To achieve optimal mechanical strength: Use FormCure 60 for 30 minutes.
The yellow hue from post-curing fades within one week.
FAQ
- Q: Can I use other cartridges instead of Clear-V4 for this resin?
- A: Yes, you can use Universal Cartridge in North America or other regions as an alternative solution.
- Q: How long should I let the paint dry after washing before post-curing?
- A: Allow the print to dry for 60 minutes in a shaded and ventilated area before UV post-curing.
- Q: What should I do if the dried print feels tacky to the touch?
- A: If the print feels tacky after drying, proceed with post-curing as recommended for optimal results.
APPLYLABWORK PRINTING INSTRUCTIONS
Form 3 Series Printers Laser Modeling Clear V2 (MD-R002CR)
Check
- The resin tank and optical path are clean
- Shake the resin bottle well before use
Cartridge
Refill this resin into a Clear-V4 cartridge. Open the air vent, turn the
cartridge upside down, drip dry through the air vent for at least 5 minutes to
minimize cross-contamination, refill, shake well, insert and print.
Alternative solution: Universal Cartridge
North America, Other Regions
PreForm Setting
- Select Printer: Form3 series
- Select Material: Clear V4
- Layer Thickness: 25-100μm
Washing
Clean IPA95% or higher, FormWash or ultrasonic cleaner for 5 minutes, after
wash shakes off or blow off residual IPA, and allow the print to dry for 60
mins in a shaded & ventilated area before UV post-curing. (The dried print
might be slightly tacky to the touch.)
Post-curing
- Optimal transparency for visual aid models, skip post-curing.
- For minimizing yellowing:
- FormCure 35 ℃ / 15 mins.
- To achieve optimal mechanical strength:
- FormCure 60 ℃ / 30 mins.
- The yellow hue from post-curing fades in one week.
Storage
- Keep resin away from heat and light.
- NOT accessible to children.
Note
- Keep printing and post-process environment well-ventilated.
- Wear gloves when handling resin and avoid direct contact.
- Repetitive printing will cause yellowing of clear-v2 resin. Pour only the needed volume for each print job.
- For ease of model removal, apply the Default Clear V4 support setting without a raft.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>