SAVANT HST-STUDIO46BG-2CH IP Audio Studio with Integrated Host and Grille Instruction Manual
- June 3, 2024
- SAVANT
Table of Contents
Savant® IP Audio Studio with Integrated Host and Grille – Black
Quick Reference Guide
Product Specific Contents
IP Audio Studio SoundBar 46 [HST-STUDIO46BG-2CH] (1) Soundbar (093-3100-xx)
(1) Standard Grille (093-3225-xx)
IP Audio Studio SoundBar 55 [HST-STUDIO55BG-2CH]
(1) Soundbar (093-3102-xx)
(1) Standard Grille (093-3226-xx)
Universal Box Contents
(1) Power Cord (064-0480-xx)
(2) 6-pin Control Connector [pre-installed] (028-9352-xx)
(1) Install Kit (075-0256-xx)
(1) Pair of White Gloves (099-0348-xx)
(2) Wall Mounting Bracket (071-1130-xx)
(1) 3mm Allen Wrench (015-0222-xx)
(8) M5x10mm hex screw (039-0440-xx)
(4) 25mm Washer 5mm ID (039-0437-xx)
(2) 50×90 Bracket Extension (071-1112-xx)
(2) 70×90 Bracket Extension (071-1113-xx)
(2) Plastic Feet (074-1030-xx)
(2) Rubber Pads for Feet (073-0014-xx)
(1) Product Regulatory Insert (009-1950-xx)
Optional Accessories (sold separately)
– Soundbar TV Mount Hardware (MNT-STUDIO-TV-xx)
– Custom Grilles matched to Flat Panel TV
Front Panel
A Front Tweeters| STUDIO46: (2) 25 mm Vifa DX Super Audio Tweeters STUDIO55:
(2) 25 mm Vifa XT Super Audio Tweeters
---|---
B Midrange/ Woofers| (4 or 6) 89 mm Long Throw Carbon Fiber Midrange/Woofers
Specifications
Environmental
Temperature| 32° to 104° F (0° to 40° C)
Humidity| 10% to 90% Relative Humidity (non-condensing)
Dimensions and Weight
| Height| Width Depth| Weight
STUDI046 Dimensions (with included grille)| 4.78 in
(12.14 cm)| 45.4 in
(115.32 cm)| 2.76 in
(7.03 cm)| 13.5 lbs (6.12 kg)
STUDI055 Dimensions (with included grille)| 4.67 in
(11.87 cm)| 54.1 in
(137.41 cm)| 2.76 in
(7.03 cm)| 20.0 lbs (9.07 kg)
STUDIO46 Shipping| 9.25 in
(23.49 cm)| 54.5 in
(138.43 cm)| 6.1 in
(15.94 cm)| 20.0 lbs
(9.07 kg)
STUDI055 Shipping| 9.6 in
(24.38 cm)| 63.2 in
(160.52 cm)| 6.5 in
(16.51 cm)| 26.5 lbs
(12.02 kg)
Power
Input Power| 100/240V AC (50/60 Hz)
Maximum Power Draw| 250W
Networking
Supported Standard| IEEE 802.1 AVB/TSN switches
Operating Parameters
Frequency Response| 80 Hz – 40 kHz +/- 3 dB
Sensitivity| 89 dB ii 2.83V/1 meter
Regulatory
Safety and Emissions|
RoHS| Compliant
Minimum Supported Release
Software Release| da Vinci 9.1
Rear Panel
A IR| (3) IR Ports
Uses 6-pin IR Connectors to send IR signals to control devices with an IR
input or IR receiver via an IR flasher (5V tolerant only). See the Savant® IP
Audio Products with Integrated Host Deployment Guide
for important precautions regarding IR functionality before making any
connections.
---|---
B RS-232| (2) RS-232 Ports
Uses 6-pin Screw down plug-in connection.
Transmits and receives serial data to and from serial controllable devices.
For pinout information,
refer to the RS-232 Wiring section below.
C Ethernet| 8-pin RJ-45 port
10/100 Base-T auto-negotiating port.
Supports Audio Video Bridging (AVB).
D Power| 100/240V AC (50/60 Hz)
E Status LED| Green Blinking: Embedded system is ready, but no communication
has been established with the host. Green: Host has established communications
with the embedded system.
Red Blinking: Embedded firmware is running, but has not received a DHCP IP
Address.
Red: Host has determined the firmware needs to be updated, but a problem
occurred during the process that will initiate a reset.
Amber Blinking: Embedded system has a valid link local IP Address and is
connecting to the host.
Amber: Host is updating the embedded firmware.
Off: Embedded processor is resetting, or is powered up, and is booting the
embedded firmware.
Hardware Failure: If a hardware failure occurs, the status LED indication will
be interrupted every three seconds with a solid red indication. For example,
if the LED is blinking green when a hardware failure occurs, the LED will
alternate between blinking green and solid red at three-second intervals.
F Reset| Resets the network settings to DHCP.
Hold Reset Button for 5 seconds while Powered On to clear static IP address.
Status
LED will turn off and then Amber while the unit reboots with default network
settings.
G Digital Audio In| Digital optical audio inputs (TOSLINK).
Supports up to 192kHz/24-bit digital audio in; PCM stereo format only.
Side and Bottom Panel
| A Stage Tweeters | (2) 19mm Silk Tweeters |
|---|---|
| B Mounting Slide | (2) Captive M5 threaded bracket |
Wall Mount
NOTE: Make all wiring connections to soundbar before mounting to brackets.
-
Using the four included drywall screws, affix wall mounting brackets to the wall, allowing sufficient space between brackets to ensure stability.
NOTE: The quantity of studs affects the proper screw position. -
Make all wiring connections to soundbar before mounting to brackets.
-
Using the included allen key, align the threaded screw holes of the captive slider with the openings on base of the wall mount bracket. Repeat this step for the second wall bracket
-
Make any minor height adjustments using the 6 mm set screw on the bottom of the bracket.
-
Attach the soundbar by threading M5x10mm screws through wall brackets and into the soundbar’s captive mounting slide brackets.
Plastic Feet
- Align the captive M5 threaded brackets in the soundbar mounting slide beneath the center speakers of right and left side channels.
- Secure plastic feet to the captive brackets using M5x190mm screws.
- Remove wax paper from the adhesive backing on included rubber pads and attach one to each of the plastic feet.
For more information on installing this SoundBar see the Savant IP Audio Studio with Integrated Host Deployment Guide on the Savant Customer Community.
IP Audio Studio with Integrated Host QRG | 009-1835-05
Copyright © 2022 Savant Systems, Inc. | 220829
45 Perseverance Way, Hyannis, MA 02601
Savant.com
508.683.2500
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>