SAVANT CLEDA199LD1 LED Lamp User Guide
- June 5, 2024
- SAVANT
Table of Contents
CLEDA199LD1 LED Lamp
User Guide
Simple DIY Setup
1. Screw or plug in your smart lights and power them on.|
---|---
2. Download the C by GE app.|
3. Add your devices to the C by GE app.|
Voila! You can now enjoy scheduling, scene-setting, app, voice, and out-of- home control of your lights!
How to Enable
Out of Home Control and Voice Control with Amazon Alexa and Google Home or Nest Hub device
1. Screw or Plug-In and power on your smart lights.|
---|---
2. Download the C by GE app.|
3. Enable voice control by following the directions in your voice assistant’s
app.|
GE Connected A19 CLEDA199LD1, input 120Vac, the frequency was 60Hz, high efficiency, safety & stability output. Use Bluetooth 4.2 and Wi-Fi 2.4G Hz chip technology to realize the far distance control. Through the APP to control the PWM signal to dim and even control the switch on & off of the bulb.
Product features:
- Controlled by Bluetooth 4.2 and 2.4G Wi-Fi to realize the far distance control.
- CCT is 2700K.
- With advanced chips to make sure the bulb with high efficiency, low consumption, and stability.
- Internal constant current output to make sure the high power conversion efficiency and stability output.
Product Name | LED LAMP |
---|---|
Brand Name | GE |
Model No. | CLEDA199LD1 |
Working Voltage | 120Vac |
Bluetooth Specification | Version 4.2 |
Wi-Fi Specification | 2.4G Hz |
Frequency Range | 2400- 2483.5MHz |
Channel Number Bluetooth | 40 |
Channel Separation Bluetooth | 2MHz |
Type of Modulation Bluetooth | GFSK |
Data Rate Bluetooth | 1Mbps(GFSK) |
Channel Number Wi-Fi | 11 |
Channel Separation Wi-Fi | 5MHz |
Data Rate Wi-Fi | 802.11b:11, 5.5,2,1 Mbps |
802.11g: 54,48,36,24,18,12,9,6 Mbps
802.11n: up to 65Mbps
Antenna Type| Metal Monopole
Peak Antenna Gain Bluetooth| 0.62 dBi
Peak Antenna Gain Wi-Fi| -1.17 dBi
For additional help, and regulatory and safety information, please go to:
Federal Communications Commission (FCC) Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
The grantee is not responsible for any changes or modifications not expressly
approved by the party responsible for compliance. Such modifications could
void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator and your body.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator & your body.
CAUTION:
- DO NOT USE WITH STANDARD DIMMERS, SEE INSTRUCTIONS
- NOT FOR USE IN TOTALLY ENCLOSED LUMINAIRES
- SUITABLE FOR DAMP LOCATIONS
- THIS DEVICE IS NOT INTENDED FOR USE WITH EMERGENCY EXITS
Only use the control provided with or specified by these instructions to control this lamp. This lamp will not operate properly when connected to a standard (incandescent) dimmer or dimming control.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>