Kmart NZ Evo Dino Dinosaur Mini Tri Scooter Instruction Manual
- June 15, 2024
- Kmart NZ
Table of Contents
Kmart NZ Evo Dino Dinosaur Mini Tri Scooter
Parts List
| No. | Description | Qty |
|---|---|---|
| I | Frame | I |
| 2 | Front-wheel with fork | 1 |
| 3 | Handlebar with a grip | I |
| 4 | Handlebar stem | I |
| 5 | HandIe bar pad | I |
| 6 | Rear wheel | 2 |
| 7 | Rear axle | 1 |
| 8 | Clamp cover | 1 |
| 9 | Clamp | I |
| 1.0 | Plastic head bush washer | 2 |
| l l | Gasket | 2 |
| 12 | M8nut | 2 |
| 13 | M6x27 bolt | 2 |
| 14 | M6nut | 2 |
| 15 | Rear wheel cover | 2 |
Safety and Warnin2
- Be sure to read all the instructions carefully and assemble the scooter according to this instruction manual before you allow your child to ride.
- The maximum user weight limit for this product is 20kgs
- This scooter requires assembly by an adult
- Special care should be taken to instruct children in safe riding
- Children should always be supervised while riding this scooter
- Always wear a helmet and protective pads
- Don’t use the scooter at night
- Don’t use on wet, uneven, or unpaved roads
- Check the scooter before each use to determine if there are any potential hazardous parts or conditions.
- Use of the scooter requires skill and therefore great care should be taken to avoid any falls or collisions that would injure the user or third parties.
- Be sure the rider is wearing appropriate footwear when riding the scooter.
- Allows follow traffic laws
- This scooter is not designed for off-road use and is not recommended for stunt riding
- Do not ride on public roads or near any motor vehicles
- The toy shall be used with caution, since it requires great skill, to avoid falls or collisions causing injury to the user and third parties.
Exploded Diagram/Part Description
Assembly Instructions
- Rear Wheels:
- a. Insert the rear axle (7) with MS nut pre-installed through the first rear wheel.
- b. Then insert the axle through the hole in the first extruded bush until it comes through the second bush.
- c. Insert the axle through the second rear wheel.
- d. Attach an M8 nut ( 12) onto the axle, and secure both nuts tightly.
- e. Push the rear wheel cover (15) into the hub of the wheel.
- Handle Bars:
- a. Align the holes on the handlebar (3) and the handlebar stem (4).
- Install one M6 nut(14)with gasket (1 1)onto each bolt and tighten it securely.
- b. Place the handlebar pad (5) over the handlebar and secure it tightly with the Velcro straps.
- Front Fork and Handle Bar Stem:
- a. slide clamp (9) onto the top of the fork tube, and ensure the nut and bolt face towards the footplate.
- b. Slide clamp cover (8) onto the middle of the handlebar stem ( 4 ).
- c. insert handle stem (4) into the head tube on main the frame, and ensure the handlebars are aligned at right angles with the front wheel.
- d. Tighten clamp (9) securely with a spanner or adjustable wrench. Slide clamp covers down to cover clamp assembly.
- Thanks for your purchase of this product. If any parts are missing or damaged, please contact one of our Customer Service Representatives by phone on 1800-632-792 ( Australia)
- 0800-623-792 (New Zealand)
- via email at spares@hunterleisure.com.au
- visit www.momentumservicesco.com
- Hunter Leisure Pty, Ltd
- 94 Keilor Park Drive Tullamarine, 3043, Victoria, Australia
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>