GETPRO LCDK-11-3C71 70 Inch Acrylic Flatbottom Oval Non-Whirlpool Bathtub Instruction Manual

GETPRO LCDK-11-3C71 70 Inch Acrylic Flat bottom Oval Non-Whirlpool Bathtub

FREESTANDING BATHTUB

READ ALL INSTRUCTIONS BEFORE UNPACKING THE PRODUCT

INSTRUCTIONS THAT, IF IGNORED COULD RESULT IN DEATH OR SERIOUS INJURY CAUSED BY INCORRECT HANDLING OR INSTALLATION OF THE PRODUCT. THESE INSTRUCTIONS MUST BE OBSERVED FOR SAFE INSTALLATION.

2 PEOPLE ARE REQUIRED TO LIFT AND DURING ENTIRE INSTALLATION OF THIS PRODUCT

This products must be installed by a fully insured and licensed plumber only. Installation of any our product by anyone other than fully insured and licensed plumber shall void limited warranty. We recommends that such
licensed plumber have experience in the installation of products.
Limited warranty is void on any commercial installation
We are not responsible for local code compliance for this product. Building and plumbing codes may vary from state-to-state in accordance to your loca~on. We are not resonsible for providing any compliance certifications.
Under no circumstances we are shall not be liable for any and all incidental damages sustained in connection with this product
Neither manufacture, nor distributor, nor retailer is responsible for water damage or flood caused due to use of this product.
Under no circumstances We shall not be liable for any and all fees, cost of installa~on/reinstalla~on/removal, subsequent
damage or transporta~on in case of the product defect

Dimension

TOOLS REQUIRED FOR INSTALLATION (NOT INCLUDED)

Inspect the bathtub for any damages. If any damage is found please

contact your retailer.

Carefully, remove the tub from it’s crate/box.
Important Note: Bathtub must be carried by a minimum of 2 adult people in upside down posy!:f on only. Do not carry the bathtub by its panel.
To avoid scratches or damages to the bathtub be sure to set it on cardboard with sod blanket on top of the cardboard.

Set your bathtub on two 4×4 pieces of lumber so you can have access from the bottom of the bathtub. Put a tray beneath the bathtub.
Very Important! Before proceeding with install on, please check that push scupper plug, drain, and integrated overflow are properly sealed and tightened.
Push the scupper plug into a close position and fill the bathtub with cold water above the overflow level to test for overflow leakage and drain leakage.
Check for any leaks around the drain and pipe. (NOTE: Due to surface tension, it is normal for a small amount of water to pool around the drain)
If a leakage occurs please disassemble the drain line or overflow assemblies and you can apply a plumbing puny/silicone caulk to fix the leakage.
Once the leakage test was performed you may proceed to the installation.

INSTALLATION WITH UNDERFLOOR ACCESS

Step 1

Clean, level and prepare the floor for installation,
Place the tub in the exact installed local::!” on on the floor and trace the outline of the bathtub with pencil and mark the drain hole local::fon on the floor. Move the tub away so that the plumbing can be installed.

Step 2
Turn bathtub upside down and set it on a non-abrasive mat, blanket, or cardboard to prevent any scratches on tub rim. Website:

Step 3
Place a level across the boom of the tub and adjust the tub feet leveler to touch the level.
Then raise the leveler additional 1/8″ or 3/16″ so that the weight of the tub, water and user are fully supported by the feet adjuster and not the tub walls. pop up cover drain body rubber drain gasket tail piece (provided by installer) floor drain pipe (provided by installer) trap (provided by installer) rubber drain gasket P-trap.

Step 4
Install an 1-1/2″ tail piece along with the corresponding flanged washer and 1-1/2″ nut to the drain body.

Step 5
Measure and cut the tail piece to the appropriate length to reach the trap adapter When setting the tub drain, insert tail piece with 1-1/2″ slip joint and rubber washer into the trap adapter and tighten properly.

Step 6
Apply a generous bead of adhesive or waterproof silicone to the bottom of the tub and a bead of tub and tile caulk around the edge of the tub

Step 7
Flip the tub over and carefully set the tub into position with tail piece assembly to P-trap and connect to the drain

Step 8
Fill the tub with water to the overflow and then drain the tub while inspecting the waste and overflow connection below the floor for any leaks. Access from below will be necessary for this step.

Step 9
With the tub now set in place, wipe off any excess tub or tile caulking, adhesive where the tub meets the floor with wet cloth.

Step 10
DO NOT SHOWER or MOVE the tub after installation because it will take about 24 hours to get the silicone sealant to dry

Note:
If installing on a concrete slab where no underfloor access or cannot move drain.
You may consider following option

• Optional flexible drain hose from plumbing hardware or home improvement store may be used GETPRO will not supply this flexible hose). Connect one end attaches to the bathtub drain and the other end needs to be attached to the floor drain by using a transition piece.
  Optional Island tub drain may also be used.
  Create a bridge from bathtub drain to floor drain by certified plumber only because any wrong connection or loosen on connection will cause leaks

INSTALLATION ON SLAB FLOOR (NO UNDERFLOOR ACCESS)

Step 1
Clean, level and prepare the floor for installation, Place the tub in the exact installed location on the floor and trace the outline of the bathtub with pencil and mark the drain hole location on the floor. Move the tub away so that the plumbing can be installed.

Step 2
Turn bathtub upside down and set it on a non-abrasive mat, blanket, or cardboard to prevent any scratches on tub rim.

Step 3
Place a level across the bottom of the tub and adjust the tub feet leveler to touch the level. Then raise the leveler additional 1/8″ or 3/16″ so that the weight of the tub, water and user are fully supported by the feet adjuster and not the tub walls.

Step 4
Measure the actual distance from drain into drain pipe on floor and the drain pipe should extend approximately 1″ above the finish floor. Use a drain adapter (not provided) if necessary

Step 5
5. Clean the surrounding of the drain pipe with cloth in preparation of setting the drain, the area should be dry and free of any debris. Apply a bead of clear silicon or plumber putty around the drain body and pass it through the drain hole, also apply plumber putty to the washer and slide it over the bottom of the drain body.

Step 6
Apply putty to fix the rubber sip gasket over the drain vent

Step 7
Apply a generous bead of adhesive or waterproof silicone to the bottom of the tub and caulk around the edge of the tub.

Step 8
Flip the tub over and carefully set the tub into position with tail piece assembly to waste vent and connect to the drain.

Step 9
With the tub now set in place, wipe off any excess tub or tile caulking, adhesive where the tub meets the floor with wet cloth.

Step 10
DO NOT SHOWER or MOVE the tub after installa~on because it will take about 24 hours to get the silicone to dry

IMPORTANT SAFETY RULES

ATTENTION! ALWAYS FOLLOW THESE PRECAUTIONS WHEN USING A BATHTUB

Warning The bathtub must be installed and used as described in this manual
Warning Use caquelon when entering or exiting the bathtub
Warning Do not permit children or persons with infirmities to use the bathtub without supervision of an adult
Warning People using any medications or having adverse medical history must consult a physician prior to use of the bathtub to avoid potential hyperthermia and possible drowning
Warning Water temperature over 100F may cause hyperthermia and/or other health problems. Check water temperature and adjust it for your personal comfort
Warning Never use bathtub while intoxicated, adder taking meals or any alcoholic beverages. Consuming alcoholic beverages before or during bathing will cause drowsiness and may result in hyperthermia, loss of consciousness, or even drowning
Warning If you are pregnant or you feel that you are may be pregnant, consult your doctor before using the bathtub
Warning Never use any electrical devices such as hair dryer, lamp, telephone, tv, radio, or others within 5 feet of the bathtub
Warning Do not overfill the bathtub before entering. Entering the bathtub when filled will cause overflow and slippery conditions. Use extreme caution when entering and exiting

Care and Cleaning

• Most dirt will wash off with mild soap and warm water.
• For tough spots, use liquid dish washing soap or non-chlorine bleach.
• Do not use abrasive material such steel wool or scouring pads to clean the acrylic surface.
• Always test the cleaning solution on a small area before using it on the feeler surface.
• Do not allow cleaning to soak on the acrylic surface.
• Rinse thoroughly with water immediately and wipe dry with soft cloth.

Repair and Maintenance

• Use liquid polish compound such as Gel-Gloss Kitchen and Bath Polish(TM) to keep the original shine of acrylic surface.
• Light scratches can be removed with polishing compound for automobiles.
• For deeper scratches use wet sandpaper (1500 grit or higher). Always add water when sanding and lightly sand the area larger than the scratch in a circular moon to remove the scratches. Repeat until the scratch is removed. Use soft cloth and small amount of polishing compound to restore shine. Repeat as needed until surface shine is restored.

IMPORTANT!

DO NOT USE: Abrasive cleaners such as: acid, ammonia, bleach, and similar solutions. Use of such solutions may cause corrosion, finish peeling, and/or dull the surface.
DO NOT USE: Abrasive sponges or cloth. Never use steel, wool, or wired brushes that will permanently scratch the surface.

More Wholesale Price Home Furniture Products
at
www.getprohome.com
GET30%off
on any of your next purchase special offers & other discounts information **send us email to
[ service@getprohome.com**](mailto:service@getprohome.com)

Documents / Resources

| GETPRO LCDK-11-3C71 70 Inch Acrylic Flatbottom Oval Non-Whirlpool Bathtub [pdf] Instruction Manual
LCDK-11-3C71 70 Inch Acrylic Flatbottom Oval Non-Whirlpool Bathtub, LCDK-11-3C71, 70 Inch Acrylic Flatbottom Oval Non-Whirlpool Bathtub, Flatbottom Oval Non-Whirlpool Bathtub, Non-Whirlpool Bathtub, Bathtub
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>