GETPRO GS310 67 Inch Acrylic Flatbottom Single Slipper Non-Whirlpool Freestanding Soaking Bathtub Instruction Manual

GETPRO GS310 67 Inch Acrylic Flatbottom Single Slipper Non-Whirlpool Freestanding Soaking Bathtub Instruction Manual

INSTALLATION AND CARE GUIDE

FREESTANDING BATHTUB

TOOLS REQUIRED FOR INSTALLATION (NOT INCLUDED)

2 PEOPLE ARE REQUIRED TO LIFT AND DURING ENTIRE INSTALLATION OF THIS PRODUCT

Carefully, remove the tub from it’s crate/box. Important Note: Bathtub must be carried by a minimum of 2 adult people in upside down position only. Do not carry the bathtub by its panel.

To avoid scratches or damages to the bathtub be sure to set it on cardboard with soft blanket on top of the cardboard.

Set your bathtub on two 4×4 pieces of lumber so you can have access from the bottom of the bathtub. Put a tray beneath the bathtub.

Very Important! Before proceeding with installation, please check that push scupper plug , drain, and integrated overflow are properly sealed and tightened.

Push the scupper plug into a close position and fill the bathtub with cold water above the overflow level to test for overflow leakage and drain leakage.

Check for any leaks around the drain and pipe. (NOTE: Due to surface tension, it is normal for a small amount of water to pool around the drain)

If a leakage occurs please disassemble the drain line or overflow assemblies and you can apply a plumbing putty/silicone caulk to fix the leakage.

Once the leakage test was performed you may proceed to the installation.

INSTALLATION WITH UNDERFLOOR ACCESS

Step 1   Clean, level and prepare the floor for installa-tion, Place the tub in the exact installed location on the floor and trace the outline of the bathtub with pencil and mark the drain hole location on the floor. Move the tub away so that the plumbing can be installed.

Step 2
Turn bathtub upside down and set it on a non-abrasive mat, blanket, or cardboard to prevent any scratches on tub rim.

Step 3

Place a level across the bohom of the tub and adjust the tub feet leveler to touch the level. Then raise the leveler additonal 1/8″ or 3/161 so that the weight of the tub, water and user are fully supported by the feet adjuster and not the tub walls.pop up cover drain body rubber drain gasket tail piece (provided by installer) floor drain pipe (provided by installer) trap (provided by installer) rubber drain gasket Ptrap.

Step 4

Install an 1-1/2″ tail piece along with the corresponing flanged washer and 1-1/2′ nut to thedrain body.

Measure and cut the tail piece to the appropriate length to reach the trap adapter When seting the tub drain, insert tail piece with 1-1/2″ slip joint and rubber washer into the trap adapter and tighten properly.

Step4
Apply a generous bead of adhesive or waterproof silicone to the bottom of the tub and a bead of tub and tile caulk around the edge of the tub

Step 7
Flip the tub over and carefully set the tub into position with tail piece assembly to P-trap and connect to the drain.

S Step
Fill the tub with water to the overflow and then drain the tub while inspecting the waste and overflow connection below the floor for any leaks, Access from below will be necessary for this step.

Step 9
With the tub now set in place, wipe off any excess tub or tile caulking, adhesive where the tub meets the floor with wet cloth.

Step 10
NOT SHOWER or MOVE the tub after installation because it will take about 24 hours to get the silicone sealant to dry.

Note : If installing on a concrete slab where no underfloor access or cannot move drain. You may consider following option.

Optional flexible drain hose from plumbing hardware or home improvement store may be used GETPRO will not supply this flexible hose). Connect one end ataches to the bathtub drain and the other end needs to be atached to the floor drain by using a transition piece.

Optional Island tub drain may also be used.

Create a bridge from bathtub drain to floor drain by certified plumber only because any wrong connection or loosen on connection will cause leaks.

INSTALLATION ON SLAB FLOOR (NO UNDERFLOOR ACCESS)

Step 2
Turn bathtub upside down and set it on a non-abrasive mat, blanket, or cardboard to prevent any scratches on tub rim.

Step 3
Place a level across the bottom of the tub and adjust the tub feet Leveler to touch the levet. Then raise the leveler additional 1/8″ or 3/16″ so that the weight of the tub, water and user are fully supported by the feet adjuster and not the tub walls.

Step 4
Measure the actual distance from drain into drain pipe on floor and the drain pipe should extend approximately 1″ above the finish floor. Use a drain adapter (not provided) if necessary.

Sten 5.
Clean the surrounding of the drain pipe with cloth in preparation of seting the drain, the area should be dry and free of any debris. Apply a bead of clear silicon or plumber putty around the drain body and pass it through the drain hole, also apply plumber putty to the washer and slide it over the bothom of the drain body.

Ster 6
Apply putty to fix the rubber silp gasket over the drain vent

Ster 7
Apply a generous bead of adhesive or waterproof silicone to the Step botiom of the tub and caulk around the edge of the tub.

Step 9
With the tub now set in place, wipe off any excess tub or tile caulking, Step adhesive where the tub meets the floor with wet cloth.

Step 10
DO NOT SHOWER or MOVE the tub after installation because it will take about 24 hours to get the silicone to dry.

IMPORTANT SAFETY RULES

ATTENTION! ALWAYS FOLLOW THESE PRECAUTIONS WHEN USING A BATHTUB

Warning The bathtub must be installed and used as described in this manual

Warning Use caution when entering or exiting the bathtub

Warning Do not permit children or persons with infirmities to use the bathtub without supervision of an adult

Warning People using any medications or having adverse medical history must consult a physician prior to use of the bathtub to avoid potential hyperthermia and possible drowning

Warning Water temperature over 100ºF may cause hyperthermia and/or other health problems. Check water temperature and adjust it for your personal comfort

Warning Never use bathtub while intoxicated, ader taking meals or any alcoholic beverages. Consuming alcoholic beverages befc during bathing will cause drowsiness and may result in hyperthermia, loss of consciousness, or even drowning

Warning If you are pregnant or you feel that you are may be pregnant, consult your doctor before using the bathtub

Warning Never use any electrical devices such as hair dryer, lamp, telephone, tv, radio, or others within 5 feet of the bathtub

Warning Do not overfill the bathtub before enetering. Entering the bathtub when filled will cause overflow and slippery condtions. Use extreme caution when entering and exiting

Care and Cleaning

• Most dirt will wash off with mild soap and warm water.
• For tough spots, use liquid dish washing soap or non-chlorine bleach.
• Do not use abrasive material such steel wool or scouring pads to clean the acrylic surface.
• Always test the cleaning solu on on a small area before using it on the en re surface.
• Do not allow cleaning to soak on the acrylic surface.
• Rinse thoroughly with water immediately and wipe dry with soft cloth.

Repair and Maintenance

• Use liquid polish compound such as Gel-Gloss Kitchen and Bath Polish(TM) to keep the original shine of acrylic surface.
• Light scratches can be removed with polishing compound for automobiles.
• For deeper scratches use wet sandpaper (1500 grit or higher). Always add water when sanding and lightly sand the area larger than the scratch in a circular mo·on to remove the scratches. Repeat until the scratch is removed. Use soft cloth and small amount of polishing compound to restore shine. Repeat as needed until surface shine is restored.

IMPORTANT

Retain these installation instructions for future reference!

If you have any questions or concerns, please do not hesitate to contact us

Email: service@getprohome.com

Hotline : +1 5714125962

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>