GETPRO GS324 63 Inch Oval Acrylic Flatbottom Non-Whirlpool Freestanding Soaking Bathtub Installation Guide

GETPRO GS324 63 Inch Oval Acrylic Flatbottom Non-Whirlpool Freestanding

Soaking Bathtub

Product Information

The Freestanding Bathtub is a high-quality product designed to provide a comfortable and relaxing bathing experience. The bathtub is made of durable and long-lasting material, ensuring that it will serve you for many years. The bathtub is available in a standard size and can be installed on both underfloor access and slab floor. The product comes with an installation and care guide to help you with the installation process and provide you with information on how to take care of the bathtub.

Tools Required for Installation

• Cloth or Blanket
• Silicone
• Tape Pencil/Marker
• Measure
• Hammer
• Safety Glass
• Knife
• Level
• Caulk Gun
• Adjustable Wrench
• Channel Lock Pliers

Note: Other tools may be required.

Product Important Safety Rules

• Always follow the precautions when using a bathtub.
• Do not use abrasive cleaners such as acid, ammonia, bleach, and similar solutions as they may cause corrosion, finish peeling, and/or dull the surface. Do not use abrasive sponges or cloth. Never use steel, wool, or
  wired brushes that will permanently scratch the surface.

Product Care and Cleaning

To clean the bathtub, use a non-abrasive cleaner and a soft cloth to wipe the surface. For scratches, use a sanding block and lightly sand the area larger than the scratch in a circular motion to remove the scratches. Repeat until the scratch is removed. Use a soft cloth and a small amount of polishing compound to restore shine. Repeat as needed until surface shine is restored.

Product Usage Instructions

Installation with Underfloor Access

1. Prepare the tools required for installation.
2. Follow the installation steps 2 to 10 as provided in the installation guide.
3. After installation, wipe off any excess tub or tile caulking, adhesive where the tub meets the floor with a wet cloth.
4. Do not shower or move the tub after installation because it will take about 24 hours to get the silicone to dry.

Installation on Slab Floor (No Underfloor Access)

1. Prepare the tools required for installation.
2. Turn the bathtub upside down and set it on a non-abrasive mat, blanket, or cardboard to prevent any scratches on the tub rim.
3. Place a level across the bottom of the tub and adjust the tub feet leveler to touch the level. Then raise the leveler additional 1/8 or 3/16 so that the weight of the tub, water, and user are fully supported by the feet adjuster and not the tub walls.
4. Measure the actual distance from drain into drain pipe on the floor and ensure that the drain pipe should extend approximately 1 above the finish floor. Use a drain adapter (not provided) if necessary.
5. Clean the surrounding of the drain pipe with cloth in preparation of setting the drain. The area should be dry and free of any debris. Apply a bead of clear silicon or plumber putty around the drain body and pass it through the drain hole. Also, apply plumber putty to the washer and slide it over the bottom of the drain body.
6. Apply putty to fix the rubber slip gasket over the drain vent.
7. Apply a generous bead of adhesive or waterproof silicone to the bottom of the tub and caulk around the edge of the tub.
8. Flip the tub over and carefully set the tub into position with tail piece assembly to waste vent and connect to the drain.
9. With the tub now set in place, wipe off any excess tub or tile caulking, adhesive where the tub meets the floor with a wet cloth.
10. Do not shower or move the tub after installation because it will take about 24 hours to get the silicone to dry.

Note: Two people are required to lift and during the entire installation of this product.

If you have any questions or concerns about the product or its usage, please do not hesitate to contact us at Get Your Home a Pro Choice.

INSTALLATION AND CARE GUIDE

FREESTANDING BATHTUB

SIZE

TOOLS REQUIRED FOR INSTALLATION (NOT INCLUDED)

CAUTION: 2 PEOPLE ARE REQUIRED TO LIFT AND DURING ENTIRE INSTALLATION OF THIS PRODUCT

carefully, mnove the tub from It’s crate/box.

• Important Nate: Bathtub must be carried by a minimum of 2 adult people in uplide down posi on only. Do not cany the bathtub by its penal.

• To avoid scrall: ha& or damages to tha bathtub be 1111& to 1181: it on cardboard with aoft blankat on top cf Iha cardboard.

• Set your bathtub on two 4×4 pieces of lumber so you can have access from the bottom of the bathtub. Put a tray beneath the bathtub.

• Very Important! Before proceeding with installation, please check that push scupper plug, drain, and integrated overflow are properly sealed and tightened.

• Push the scupper plug into a close position and fill the bathtub with cold water above the overflow level to test for overflow leakage and drain leakage.

• Check for any leaks around the drain and pipe. (NOTE: Due to surface tension, it is normal for a small amount of water to pool around the drain)

• If a leakage occurs please disassemble the drain line or overflow assemblies and you can apply a plumbing puhy/silicone caulk to fix the leakage.

• Once the leakage test was performed you may proceed to the installation.

INSTALLATION WITH UNDERFLOOR ACCESS

Step 1: Clean, level and prepare the floor for installa- tion, Place the tub in the exact installed loca& on on the floor and trace the outline of the bathtub with pencil and mark the drain hole location on the floor. Move the tub away so that the plumbing can be installed.

Step 2 Tum bathtub upside down and setit on a non.-abrasive mat, blanket, or cardboard to prevent any scratches on tub rim.

Step 3
Place a level across the bohom of the tub and adjust the tub feet leveler to touch the level. Then raise the leveler additonal 1/8″ or 3/16″ so that the weight of the tub, water and user are fully supported by the feet adjuster and not the tub walls.pop up cover drain body rubber drain gasket tail piece (provided by installer) floor drain pipe (provided by installer) trap (provided by installer) rubber drain gasket P-trap.

Step 4
Install an 1-1/2″ tail piece along with the corresponing flanged washer and 1-1/2″ nut to thedrain body.

Step 5
Measure and cut the tail piece to the appropriate length to reach the trap adapter When seting the tub drain, insert tail piece with 1-1/2″ slip joint and rubber washer into the trap adapter and tighten properly.

Step 6
Apply a generous bead of adhesive or waterproof silicone to the bottom of the tub and a bead of tub and tile caulk around the edge of the tub

Step 7
Flip the tub over and carefully set the tub into position with tail piece assembly to P-trap and connect to the drain.

Step 8
Fill the tub with water to the overflow and then drain the tub while inspecting the waste and overflow connection below the floor for any leaks. Access from below will be necessary for this step.

Step 9
With the tub now set in place, wipe off any excess tub or tile caulking, adhesive where the tub meets the floor with wet cloth.

Step 10
DO NOT SHOWER or MOVE the tub after installation because it will take about 24 hours to get the silicone sealant to dry.

Note:
If installing on a concrete slab where no underfloor access or cannot move drain.
You may consider following option.

• Optional flexible drain hose from plumbing hardware or home improvement store may be used GETPRO will not supply this flexible hose). Connect one end ataches to the bathtub drain and the other end needs to be atached to the floor drain by using a transition piece.
• Optional Island tub drain may also be used. Create a bridge from bathtub drain to floor drain by certified plumber only because any wrong connection or loosen on connection will cause leaks.

INSTALLATION ON SLAB FLOOR (NO UNDERFLOOR ACCESS)

Step 1
Clean, level and prepare the floor for installation, Place the tub in the exact installed location on the floor and trace the outline of the bathtub with pencil and mark the drain hole location on the floor.
Move the tub away so that the plumbing can be installed.

Step 2 Tupresentatusside cows and set i on a non-abrasive mat blanket. or cardboard to prevent any scratches on tub rim.

Step 3
Place a level across the bottom of the tub and adiust the tub feet leveler to touch the level. Then raise the leveler additional 1/8″ or 3/16″ so that the weight of the tub, water and user are fully supported by the feet adjuster and not the tub walls.

Step 4
Measure the actual distance from drain into drain pipe on floor and the drain pipe should extend approximately 1″ above the finish floor. Use a drain adapter (not provided) if necessary.

Step 5: Clean the surrounding of the drain pipe with cloth in preparation of seting the drain, the area should be dry and free of any debris. Apply a bead of clear silicon or plumber putty around the drain body and pass it through the drain hole, also apply plumber putty to the washer and slide it over the bothom of the drain body.

Step 6
Apply putty to fix the rubber silp gasket over the drain vent

Step 7
Apply a generous bead of adhesive or waterproof silicone to the botiom of the tub and caulk around the edge of the tub

Step 8 fleetasemiero waste vent and connecto the train. wthtal. piece assembly to waste vent and connect to the drain.

Step 9
With the tub now set in place, wipe off any excess tub or tile caulking, adhesive where the tub meets the floor with wet cloth.

Step 10
DO NOT SHOWER or MOVE the tub after installa on because it will take about 24 hours to get the silicone to dry.

IMPORTANT SAFETY RULES

ATTENTION: ALWAYS FOLLOW THESE PRECAUTIONS WHEN USING A BATHTUB

Warning

• The bathtub must be installed and used as described in this manual
• Use cau on when entering or exiting the bathtub
• Do not permit children or persons with infirmities to use the bathtub without supervision of an adult
• People using any medications or having adverse medical history must consult a physician prior to use of the bathtub to avoid potential hyperthermia and possible drowning
• Water temperature over 1009F may cause hyperthermia and/or other health problems. Check water temperature and adjust it for your personal comfort
• Never use bathtub while intoxicated, ader taking meals or any alcoholic beverages. Consuming alcoholic beverages before or during bathing will cause drowsiness and may result in hyperthermia, loss of consciousness, or even drowning
• If you are pregnant or you feel that you are may be pregnant, consult your doctor before using the bathtub
• Never use any electrical devices such as hair dryer, lamp, telephone, tv, radio, or others within 5 feet of the bathtub
• Do not overfill the bathtub before entering. Entering the bathtub when filled will cause overflow and slippery condtions. Use extreme caution when entering and exiting

Care and Cleaning

• Most dirt will wash off with mild soap and warm water.
• For tough spots, use liquid dish washing soap or non-chlorine bleach.
• Do not use abrasive material such steel wool or scouring pads to clean the acrylic surface.
• Always test the cleaning solution on a small area before using it on the entire surface.
• Do not allow cleaning to soak on the acrylic surface.
• Rinse thoroughly with water immediately and wipe dry with soft cloth.

Repair and Maintenance

• Use liquid polish compound such as Gel-Gloss Kitchen and Bath Polish (TM) to keep the original shine of acrylic surface.
• Light scratches can be removed with polishing compound for automobiles.
• For deeper scratches use wet sandpaper (1500 grit or higher). Always add water when sanding and lightly sand the area larger than the scratch in a circular motion to remove the scratches. Repeat until the scratch is removed. Use soft cloth and small amount of polishing compound to restore shine. Repeat as needed until surface shine is restored.

IMPORTANT

• DO NOT USE: Abrasive cleaners such as: acid, ammonia, bleach, and similar solutions. Use of such solutions may cause corrosion, finish peeling, and or dull the surface.
• DO NOT USE: Abrasive sponges or cloth. Never use steel, wool, or wired brushes that will permanently scratch the surface.

Retain these installation instructions for future reference!
If you have any questions or concerns, please do not hesitate to contact us

• Email: service@getprohome.com
• Hotline: +1 5714125962
• www.getprohome.com
• service@getprohome.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>