Xblitz Uni Pro 1 Wireless Bluetooth Earphones User Manual

Xblitz Uni-Pro 1 Wireless Bluetooth Earphones

Thank you for purchasing the Xblitz UNI PRO1 wireless earphone set. Please read the attached instructions and safety measures before using the device.

 SAFETY MEASURES

To use the earphone set correctly and safely, read the instructions below. When using the set, follow the following rules:

1. Adjust the volume when using the earphone set correctly.
2.  In a situation of emergency, stop using the set to ensure your safety.
3. Do not use the set to listen to music, or make or receive calls while driving a car.
4. Put the product, together with accessories, in a place inaccessible for children to avoid the danger caused by improper use.
5. Prevent water from entering the Earphones during cleaning, as this can cause sound distortion and even lead to damaging the set.
6. Avoid setting the volume too high, i.e. to the levels that make if impossible to hear anything around you. If you hear a buzzing noise in your ears or feel that the volume is too high, you should immediately reduce the volume.
7. Stop using the set if there is pronounced discomfort, irritation or other unwanted reactions.
8. In case of excessive overheating of headphones, stop using them immediately and contact an Authorized Service Center.

MAIN FEATURES

1.  Ability to wirelessly play music from your phone.
2. Ability to make wireless phone calls.
3. Handy earphone charging case.
4. Voice messages in English that indicate the status of batteries, incoming connections, disconnecting the device, etc.

PACKAGE CONTENTS

1. Earphones
2. Charging case
3. USB cable (charging)
4. User’s manual
5. 2 sets of spare rubber tips

GETTING STARTED

Automatic pairing

1. Remove the insulation tape from the earphones and reinsert them into the charging case to charge both earphones.
   WARNING: If the set does not charge when placed in the case, please connect the USB power cord to the power port of the case.

2. After taking the earphones out of the case (which ear each earphone goes into is marked on the inside of the case. R- to the right ear, L – to the left ear), each of them should have a blue LED flashing, indicating that the device has been turned on.

3. If the earphone LEDs are alternating between blue and red, the device is ready to pair. Turn on BT connectivity on your phone and on the list of available devices to connect to your phone, select Xblitz UNI PRO 1. When the earphones are paired with the phone, the LEDs on them will stop flashing and corresponding information (e.g. “Connected, 100% battery left”) will be displayed on your phone in the BT connectivity menu.

4. the earphones will automatically turn o when they are put into the case.

5. Taking the earphones out of the case will automatically turn them on and pair them again with your phone.

Manual pairing

(When automatic pairing fails)

1. Press and hold the button on the earphone for 3 seconds to turn it on. A LED in the device will start flashing blue when turned on.

2. Press and hold the button on the earphone for

3. seconds, and then double-click again to turn on pairing mode. The pairing mode is indicated by LEDs of the device alternating between blue and red.

4. Turn on BT connectivity on your phone and on the
   list of available devices to connect to your phone, select Xblitz UNI PRO 1. When the earphones are paired with the phone, the LEDs on them will stop flashing.

5. The earphones will automatically turn o when they are put into the case.

6. Taking the earphones out of the case will automatically turn them on and pair them again with your phone.

BUTTON FUNCTIONS

1. Turning on/ o – holding the button of any of the earphones for 3-4 seconds turns the device on/ o .
2. Play/ stop – briefly press the button on any of the earphones to turn music playback on/ o
3.  Answer/ End phone call – press the button on the left earphone to answer a phone call or end the call.
4. Reject call – hold the button on the left earphone for 1 second to reject the incoming call.
5. Change tracking – double-tap the button of any of the earphones to change the music track you play. Pressing the left earphone button plays the previous track, and pressing the right earphone button – the next one.

CONNECTING TO SMART ASSISTANT (e.g. Siri)
When you’re using earphones or they’re in standby mode, press and hold the left earphone button for 1 second to turn on the assistant. Doing it again will turn the assistant o .

SINGLE EARPHONE MODE
You can connect to your phone using only the main (left) earphone, leaving the additional (right) earphone in the charging case. The earphone will automatically connect to the phone with which the set is paired. If you want to switch from using a single earphone to both earphones – take the right earphone out of the case and hold its button for 3 seconds. The earphones connect to each other.

CHARGING

To charge the earphones, place them in the case. Magnets placed in the case should keep the earphones in place. If charging starts successfully, the earphone LEDs will light up red and the LED inside the case will flash blue. When the LEDs turn o , the charging is complete. To charge the battery in the case, connect it to a power supply using a regular 5V charger with a micro USB cable. The number of lit LEDs inside the case during charging indicates the battery charge status.

1.  Blue LED – 0-25% charged battery
2.  blue LEDs – 25-50% charged battery
3.  blue LEDs – 50-75% charged battery
4.  blue LEDs – 75-100% charged battery

SPECIFICATIONS

WARRANTY CARD/ COMPLAINTS
The product is covered by a 24-month warranty. The terms of the guarantee can be found at: https://xblitz.pl/warranty/ Complaints should be reported using the complaint form located at: http://reklamacje.kgktrade.pl/ Details, contact and website address can be found at: www.xblitz.pl Specifications and contents of the kit are subject to change without notice. We apologize for any inconvenience. KGK Trade declares that this device XBLITZ UNI PRO 1 is compliant with significant requirements of directive 2014/53/EU. The text of this declaration may be found on the website: http://xblitz.pl/download/DOC /delaracja-CE-Xblitz-uni-pro1.pdf
Manufacturer: KGK Trade sp. z o.o. sp. k. Ujastek 5b
31-752 Cracow  Polan Made in P.R.C.

The crossed-out trash can symbol indicates that unusable electrical or electronic devices, its accessories (such as power suppl ies, cords) or components (for example batteries, if
Included) cannot be disposed of alongside household waste. In order to dispose of the devices or Their components (for example, batteries) deliver the device to the collection point, where it will be accepted free of charge. Disposal is subject to the recast version of the WE EE Directive (2012/19 / EU) and the Directive an batteries and accumulators (2006/66 / EC). Proper disposal of the device prevents the degradation cf the natural environment. Information about the collection points of the facilities Is Issued by the competent local authorities. Incorrect disposal of waste Is subJect to penalties provided for by the law In force In the given area.

References

• System reklamacyjny KGK Trend
• Warranty - Xblitz.pl

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>