Xblitz BLACK 4K Dash Black 4K Camera Black User Manual

: June 1, 2024
: Xblitz

Table of Contents

Xblitz BLACK 4K Dash Black 4K Camera Black
KIT
PRODUCT DESCRIPTION
BEFORE USE
MONTAGE
MENU FUNCTIONS
APPLICATION FOR PLAYBACK OF RECORDINGS AND ROUTES
PRECAUTIONS
FAQ
Handle detaches from the windshield/does not stick
SPECIFICATION
WARRANTY/COMPLAINT CARD
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Xblitz BLACK 4K Dash Black 4K Camera Black

VIDEO RECORDER
Carefully read the enclosed operating instructions and safety notes before use to avoid accidental damage to the equipment or unintentional injury.

PRODUCT PURPOSE
The Xblitz Black 4K car camera with a built-in GPS module allows you to monitor the route, position and speed of your vehicle and record any traffic incidents. The video recorder is created from the highest quality components.

KIT

Video recorder
GPS module
Car charger
Operating instructions
Cable clips
Strap undermining paddle
Micro SD card reader on USB

PRODUCT DESCRIPTION

SEE FIG. A

Xblitz-BLACK-4K-Dash-Black-4K-Camera-Black-FIG-1

Function keys (from left):
- Activate/deactivate audio recording/ navigation key „back”.
- Browsing through the gallery of stored recordings and photos/ navigating key „up” /in recording mode takes a picture.
- The settings menu/navigation key „down” /in recording mode manually locks the video to protect it from being overwritten.
- Start/stop recording/approval key.
GPS module mounting
Lens
USB-C input for GPS module (also charges the device)
Device mini-USB input
Micro SD memory card slot
Indicator LED
Power button
Loudspeaker
Display
Reset
Microphone

BEFORE USE

It is recommended to use original micro SD cards up to 256GB class 10 or higher.
Before inserting the card into the recorder, it must be formatted in the computer using the supplied micro SD card reader to USB in the FAT32 or exFATfile system (depending on the card) and then in the recorder.
The memory card must be installed when the device is switched off, otherwise the card and the device may be damaged. The same applies when removing the card.
The battery allows recording without power for no more than 5 minutes.
When the memory card fills up, the oldest unprotected recordings are overwritten.
It is recommended that the functions of the device are used as intended, i.e. not to use e.g. motion detection and parking mode while driving, as this may cause the device to switch on and off automatically, e.g. when stopping at an intersection.
It is recommended that the G – SENSOR option is set to the minimum to avoid securing unnecessary material and thus losing space on the memory card.
Sound: the device has a condenser microphone that records all ambient sounds. Sounds may overlap causing distortion.

Attention!
The Black 4K device connected to the cigarette lighter socket starts up automatically every time voltage is present in the socket, and is similarly switched off automatically when the voltage disappears. Default recording starts when the video recorder is switched on if there is a formatted micro SD card in the device.

MONTAGE

SEE FIG. B

Select and clean the camera mounting location.
Mount the camera mount.
Insert the memory card into the slot in the camera. Place the camera in the mount.
Point the camera lens towards the roadway.
Connect the power supply to the camera.
Route the power supply cable so that it does not obstruct your view while

To access the menu, press the third button from the left with the settings icon, for navigation refer to the section See FIG. A.1 and section 2 (product description).

Resolution – Use the navigation keys to adjust your preferred resolution – 4K 30fps / 2k 30fps / FHD 60fps.
Loop recording – set the recording time (length) of the video files, when the memory card fills up the oldest recording will be overwritten. Use the navigation keys to adjust the preferred length of loop recording – 1 minute / 3 minutes / 5 minutes / off.
GPS information – displays information on the GPS position.
G-Sensor – gravity sensor. When enabled at the moment of impact, the recording file is protected from being overwritten. It is recommended to set the lowest value from the available: off/low/medium/high to avoid protecting recordings caused by shocks e.g. on an uneven road. Use the navigation keys to adjust the preferred sensitivity.
Motion detection – on/off – this mode starts recording when the camera detects movement in the lens, e.g. a person in front of the vehicle. The function works only when the camera is not recording and is under a constant power source, recordings from this mode are not protected against overwriting. Use the navigation keys to enable or disable the mode.
Parking Mode – on/off – when enabled, the camera catches a car bump e.g. during a parking bump, turns on automatically and starts recording a short video protected from overwriting. It is advisable to switch this function off for the duration of the drive, as it may block loop recording. Use the navigation keys to switch the mode on or off.
Note: To ensure that the camera properly records a full-length recording, leave it under a constant power source.
Screen saver – blank the screen after the time indicated in the settings. Use the navigation keys to adjust the preferred length from those available: off/30 seconds/1 minute/2 minutes.
Speed unit – kilometres per hour/miles per hour. Use the navigation keys to adjust your preferred unit of speed.
Audio recording – on/off. Use the navigation keys to turn the function on or off.
Volume settings – beep sound and system volume settings. Use the navigation keys to adjust your preferred setting.
HDR – on/off – this mode allows the device to dynamically change the value of underexposed and overexposed areas, making underexposed elements clearer in the recordings. Use the navigation keys to turn the mode on or off.
Fatigue alert – a warning beep at a user-set interval. Use the navigation keys to adjust the preferred interval from those available: off/1 hour/2 hours/4 hours.
Language – possibility to change the language of the menu. Use the navigation keys to adjust your preferred language.
Frequency – 50Hz / 60Hz refresh rate – 50Hz is the recommended setting. Use the navigation keys to adjust the preferred setting.
Date/time – date and time settings. Use the navigation keys to adjust the date and time.
Date stamp – on/off – function for displaying the date on recordings. Use the navigation keys to enable or disable the function.
Default settings – restores the default settings on the device.
SD format – format the micro SD card. Use the navigation keys to format the micro SD card.
Version – displays the current software version of the device.

APPLICATION FOR PLAYBACK OF RECORDINGS AND ROUTES

To play back the recordings, speed and route of the vehicle, we suggest the PC program „GX Player”, the installation file of which is automatically saved to any micro SD card installed in the device.

Instructions: Insert the micro SD card into the device, then start the device. The installation file of the „GX Player” software will automatically be saved on the memory card. Remove the card from the device and insert it into the included micro SD memory card reader, then insert the reader into your computer via the USB port. In the next step, start the installation file of the „GX Player” program from the card and follow the further instructions. In the program settings, you can change the language, units of measurement and the type of maps you wish to work with.

PRECAUTIONS

Do not disassemble the camera yourself or interfere with its construction. In the event of a malfunction, contact the service department.
Use only original accessories.
Only use the original charger supplied. The use of any other power supply may adversely affect the performance of the device, battery or GPS module.
The device may not be used in contravention of the laws of your country or region.
Permissible operating temperatures are 0-35 °C
Do not subject the device to damage or impacts.
Take care of the cleanliness of the product, especially the lens. Do not use detergents or chemicals when cleaning.
Clean only when the unit is unplugged.
Keep the device out of the reach of children.
Do not expose the device to very high temperatures or fire.
If you smell burnt plastic or electronics from the camera, unplug the unit as soon as possible and contact service.

FAQ

Device does not switch on, screen flashes

Before starting up charge the unit’s battery and check the connection in the cigarette lighter socket.

Device does not switch on/off automatically

The reason for this behaviour may be the constant power supply in the cigarette lighter socket.

Camera stops recording / does not overwrite recordings

Check: G-SENSOR - a function by which recordings with recorded overloads (e.g. uneven pavement, braking, driving off a kerb or over a speed bump, etc.) are protected from being overwritten. If you use this function, you must periodically format the memory card on your computer and then on the camera. Ultimately, each file on the data carrier will be protected from being overwritten and the device will not be able to record a further route - it will not record in a loop. We suggest setting the sensor according to your driving style and road conditions. You can also disable the option completely in which case each oldest file will be overwritten and the card will not need to be formatted periodically. After adjusting the function remember to format the memory card.

Camera switches on and off

Check: PARKING MODE/MONITOR and MOVEMENT DETECTION - function designed to operate while the vehicle is parked. Deactivate the function before setting off, as it may cause the camera to switch on and off and make random fragments of the route recordings. If the functions are disabled, check if the fault occurs without the memory card inserted.

Camera records parts of a route/randomly ongoing recordings

Check: MOVEMENT DETECTION - a function designed to operate while the vehicle is parked. You need to deactivate the function, before setting off as it can cause the camera to switch on and off and make random fragments of route recordings. If the function is deactivated check if the fault occurs without a memory card inserted.

Device shows „card full” message or does not read the card

Check the „G-sensor” and „parking mode” functions and set them to minimum. The card must be formatted in the computer in the FAT32 or exFAT file system (depending on the card) and then in the recorder. Also check: Is the selected card capacity and specification (micro SD, class 10 - U1, V10 additionally recommended) suitable for your device (we recommend using cards from reputable manufacturers, we recommend: Kingston Samsung Sandisk). If at any stage you encounter an error, replace the card with a new one from official distributors.

The device records noise, distorted, unclear sound

The device has a highly sensitive microphone that records any ambient noises. The recorded sounds may overlap. Windscreen air vents can also distort the sound.

Device does not respond

Press the Reset button briefly or return the device to factory settings.

The footage shows transverse lanes

Incorrect setting of the frame rate value. Set the frequency value to „50Hz” or „60Hz” depending on local settings.

Handle detaches from the windshield/does not stick

Degrease the surfaces well before mounting the holder on the glass. Remember to avoid high temperatures which can cause deformation of the holder and damage to the recorder itself.

NOTES

G-SENSOR – a function thanks to which recordings with recorded overloads (e.g. uneven road surface, braking, driving off a curb or over a speed bump, etc.) are protected from being overwritten. If you use this function, you must periodically format the memory card on your computer and then on the camera. Ultimately, each file on the data carrier will be protected from being overwritten and the device will not be able to record a further route – it will not record in a loop. We suggest setting the sensor according to your driving style and road conditions. This option can also be completely disabled, in which case each of the oldest files will be overwritten and the card will not need to be formatted periodically.

PARKING MODE/MONITOR – a function designed to operate while the vehicle is parked, uses battery power if the recorder is fully charged – (if it has a built-in battery). In this case, the camera starts recording a few seconds of video after detecting a shock – until the battery is discharged. When using this function, bear in mind the battery of the device, which needs to be recharged after the function activates (starts). You should deactivate the function, before setting off on a journey, as it may cause the camera to switch on and off and make random fragments of recordings from the route.

The constant power supply in the vehicle may cause this function to behave differently, e.g. leaving the camera on, which may drain the car battery.

MOVEMENT DETECTION – a function designed to operate while the vehicle is parked – requires constant power and the camera must remain switched on. The DVR will start recording automatically when motion is detected, and will stop recor-ding a few seconds after there is no movement in front of the camera lens. Please note that this function can drain the car’s battery.It is necessary to deactivate the function, before setting off on a journey, as it can cause the camera to switch on and off and make random fragments of recordings from the route.

NOTE

Due to continuous product improvement, the manufacturer reserves the right to make changes to the device and its kit without prior notice. Some functions described in this manual may differ slightly from reality.
Use only the original charger with a charging current of 5V/2A. Do not con-nect directly to a 220/230 V outlet. Failure to do so may damage the camera or lead to dangerous situations.
The GPS module may lose connection with the satellite if you are indoors or travelling through an underground tunnel. Occasionally, there may also be random signal disturbances due to electromagnetic interference. The manufacturer is not responsible for possible errors or inaccurate position indications by the GPS.
The parking mode function is based on battery power. A camera with a charged battery and active parking mode will, upon detecting a shock, start up and record a short recording and then switch off automatically to reduce battery consumption. The manufacturer accepts no responsibility for failure to record any damage caused when using the camera in parking mode.

SPECIFICATION

Processor: NTK96675
Sensor: Sony Starvis IMX307
Lens: 6G+IR
Aperture: 1.8
Recording resolution : 4K – 30 FPS / 2K – 30 FPS / FHD – 60 FPS Viewing angle: 170 degrees
Codec: H.264/H.265
G-Sensor : YES
Parking mode : YES
Loop Recording : YES
Night mode : YES
WiFi : NO
GPS : YES
Battery : built-in Li-Po 200 mAh battery
Power supply : DC 5V/2A
Built-in microphone : YES
Display : 2” 960×240
Micro SD memory card support: Up to 256 GB Class 10 and up
Video format: MP4
Photo format : JPEG
Dimensions: 49x60x36mm
Weight (with handle): 91g

WARRANTY/COMPLAINT CARD

The product comes with a 24-month warranty. Warranty conditions can be found at: https://xblitz.pl/gwarancja/ Claims should be made using the claim form found at: http://reklamacje.kgktrend.pl/ Details, contact and service address can be found at: www.xblitz.pl. Specifications and contents are subject to change without notice. We apologise for any inconvenience. KGK Trend declares that the XBLITZ BLACK 4K complies with the essential require- ments of Directive 2014/53/EU. The text of the declaration can be found at the link: https://xblitz.pl/download/DOC/deklaracja-CE-Xblitz-BLACK4K.pdf

The crossed-out trash can symbol indicates that unusable electrical or electronic devices, their accessories (such as power supplies, cords) or components (tor example batteries, if included) cannot be disposed of alongside household waste. To dispose of the devices or its components for example, , batteries deliver the device to the collection point, where it will be accepted free of charge. Disposal is subject to the recast version of the WEEE Directive (2012/19/ EU and the Directive on batteries and accumulators (2006/66 / EC). Proper disposal of the device prevents degradation of the natural environment. Information about the collection points of the facilities is issued by the competent local authorities. Incorrect disposal of waste is subject to penalties provided for by the law in force in the given area.

Manufacturer:
KGK TREND Sp. z o. o. (formerly KGK Trade Sp. z o.o. Sp. K.) st. Ujastek 5b, 31-752 Cracow, Poland. Made in PRC