beper P201UTP200 ZEN Water Fountain Instruction Manual
- June 3, 2024
- beper
Table of Contents
beper P201UTP200 ZEN Water Fountain
Precautions
Read the following instructions carefully, since they give you useful safety information about installation, use and maintenan-ce and help you avoid mishaps and possible accidents. Remove the packing and make sure that the appliance is intact, with special attention to the supply cable. The elements of the packing (plastic bags, polystyrene, etc) do not have to be accessible to the children, in order to preserve them from danger sources. It is recommended not to throw these packing ma-terial in the domestic waste, but to deliver them to the appropriate station of collection or destruction refusals, asking eventually infor-mation to the manager of the Sanitation Department of your own mu-nicipality. If the supply cord is damaged, it must be replaced by the manufac-turer, its service agent or similarly qualified persons in order to avoid a hazard. Before connecting the appliance make sure that the mains voltage corresponds to the data specified on the label.
The appliance can be damaged if the voltage is not correct. If the plug does not suit the socket, let it be replaced with another suitable plug by qualified personnel only, which shall also ensure that the section of the socket cables is suitable for your appliance power absorption. Generally, the use adaptors multiple plugs and/or extensions is not recommended; should they be necessary, please use only simple or multiple adaptors and extensions in compliance with the safety rules in force, making sure that the capacity absorption limit marked on the simple adaptors and the extensions and the maximum power limit marked on the multiple adaptor are not exceeded. Do not use the appliance if the cable or the plug shows any damages. Do not use the appliance after a possible irregular working. In this case, switch it off and do not break it open. Refer to an authorized Beper after-sale service for repair and require original spare parts only. Failing to follow these instructions may impair the safety of your appliance. This appliance is to be destined to its special purpose only. Any other use is to be considered as improper and thus dangerous. The manu-facturer cannot be responsible for any damages deriving from impro-per, wrong or incautious use.
This appliance is for household use only. To protect against electric shock, do not immerse cord, plug or any parts of the appliance into water or other fluids. Do not use the appliance near explosives, highly flammable mate-rials, gases or burning flames. Do not allow children, disabled people or every pe- ople without experience or technical ability to use the appliance if they are not properly watched over. Close supervision is necessary when any appliance used by or near children.
Some warnings
This appliance cannot be used by children, or persons with reduced physical, sensitive or intellectual capabilities, or with lack of expe-rience and knowledge, without supervision or if they are not given instructions and warnings on the correct and safe use of the device and the potential risks related to its use. Do not let children play with this appliance. Any cleaning and/or main-tenance operation cannot be carried out by children without proper surveillance. Do not immerse the item (except for the pump) and its power cable in water or other liquids. This appliance is only intended for domestic use. Do not use outdo-ors.
Description of product
- Decorative ball
- Top cover
- Base
- Pump
- Flow regulation switch
Assembling
Place the base on a flat and stable surface. Fill with water up to the rim,
and place the top cover with the pump already installed on to the base, making
sure that the pump is fully immersed and the small suction cups are attached
to the bottom.
Important: it is better to use distilled water; in the long run, lime stone and mineral residues contai-ned in tap water may, settle inside the pump, preventing its correct operation.
Place the decorative ball on top of the hole where water comes out, and the power cable inside the slot found on the back, making sure non to get the plug wet.
Operation
Make sure that the base is full of water and pump is immersed completely, then connect the plug to a wall socket. Water starts running continuously, to turn the appliance off it is necessary to unplug it from the wall socket.
Note : if water is not running, there might be some air stuck inside the pump circuit. Disconnect and re-connect the plug two or three times, until water starts running.
Important : do not connect the plug to a wall socket without filling the base with water, to avoid da-maging the pump.
It is possible to adjust the water flow with the regulation switch found on the pump; after disconnecting the plug from the wall socket, lift the top cover to access the pump, by gently pull upwards to detach the small suction cups, and slide the switch to the right or to the left to place it on the desired flow level (4 levels available). Replace the cover back on the base and connect the plug to the wall socket.
Cleaning and maintenance
The appliance doesn’t need any particular maintenance. Clean the outer surface of the top cover and of the base with a soft cloth slightly dampened (disconnect the plug from the wall socket before carrying out any cleaning or maintenance operation).
Technical data
- Power : 3W
- Power supply : 220-240V~ 50/60Hz
For any improvement reasons, Beper reserves the right to modify or improve the product without any notice.
DISPOSAL
The European directive 2011/65/EU on Waste Electrical and Electronic
Equipment (WEEE), requires that old household electrical appliances must not
be disposed of in the normal unsorted municipal waste stream. Old appliances
must be collected separately in order to optimize the recovery and recycling
of the materials they contain, and reduce the impact on human health and the
environment. The crossed out “wheeled bin” symbol on the product reminds you
of your obligation, that when you dispose of the appliance, it must be
separately collected.
GUARANTEE CERTIFICATE
This appliance has been checked in the factory. From the date of original
purchase a 24 month guarantee ap-plies to material and production defects. The
purchase receipt and the guarantee certificate must be submitted together in
case of claim to guarantee.
The guarantee is valid only with a guaranty certificate and proof of purchase
(fiscal receipt) indicating the date of purchase and the model of the
appliance
For any technical assistance, please contact directly the seller or our head
office in order to preserve the applian-ce’s efficiency and NOT TO void the
guarantee. Any intervention on this appliance by non-authorized persons will
automatically void the guarantee.
GUARANTEE CONDITIONS
If the appliance shows defects as a result of faulty material and/or
production during the period of guarantee, we guarantee repair free of charge
on condition that:
- The appliance has been used properly and for the purpose for which it has been intended.
- The appliance has not been tampered with, otherwise it is not maintainable.
- The purchase receipt shall be presented.
- The appliance showing a fair wear and tear shall not be covered by this guarantee.
Therefore, any part that could be accidentally broken or having visible signs
of use in consumable products (such as lamps, batteries, heating elements…)
the aesthetic parts are excluded from the guarantee, and any defect whatsoever
resulting from non-respect of the rules for use, negligence in usage and/or
maintenance of the appliance, carelessness, wrong or improper installation,
damage during transport and any other damage not attributable the supplier.
For every defect that could not be repaired within the guarantee period, the
appliance will be replaced free of charge. In any case, if the part to be
replaced for defect, breakage or malfunction is an accessory and/or a
detachable part of the product, Beper reserves the right to replace only the
very part in question and not the entire product Contact your distributor in
your country or after sales department Beper.
E-mail assistenza@beper.com which will forward
your enquiries to your distributor.
BEPER SRL
Via Salieri, 30 – 37050 – Vallese di Oppeano – Verona Tel. 045/7134674 – Fax
045/6984019 beper.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>