Telycam MEET USB Type C HD PTZ Camera User Manual
- September 25, 2024
- Telycam
Table of Contents
MEET+ 12
12X HDMI+USB Type C
HD PTZ Camera User Manual
V1.0
SAFETY GUIDES
- Before operation, please fully read and follow all instructions in the manual. For your safety, always keep this manual with the camera.
- The camera power input range is 100-240VAC(50-60Hz),ensure the power supply input within this rate before powering on.
- The camera power voltage is 12VDC, rated currency is 2A. We suggest you use it with the original power supply adapter supplied by the factory.
- Please keep the power cable, video cable and control cable in a safe place. Protect all cables especially the connectors.
- Operational environment: 0℃-50℃, humidity less than 90%.To avoid any danger, do not put anything inside the camera, and keep away from the corrosive liquid.
- Avoid stress, vibration and damp during transportation, storage and installation.
- Do not dismantle the camera housing and cover. For any service, please contact authorized technicians.
- RF cable and control cable should be individually shielded, and cannot be substituted with other cables. Do not direct the camera lens towards strong light, such as the sun or the intensive light.
- Use a dry and soft cloth to clean the camera housing. Applied with neutral cleaning agent when there is need to clean. To avoid damage on the camera lens, never use strong or abrasive cleaning agents on the camera housing.
- Do not move the camera by holding the camera head. To avoid mechanical trouble, do not rotate the camera head by hand.
- Put the camera on fixed and smooth desk or platform, avoid leaned installation.
- Power Supply Polarity(Drawing)
ACCESSORIES
Check all bellow items when open the package:
Camera ······································································
1
Power Adapter ····························································· 1
Power Cable ······························································· 1
RS232 Control Cable ···················································· 1
USB3.0 Cable……………………………………………………………………….………. 1
Remote Controller ························································ 1
User Manual ······························································· 1
Double-sided Adhesive……………………………………………………………….. .1
QUICK START
- Check all cable connections before power on.
- DIP Switch Setting (at the bottom of the camera):
Function（ARM）
| SW-1| SW-2| Instruction
1| OFF| OFF| Updating mode
2| ON| OFF| Debugging mode
3| OFF| ON| Undefined
4| ON| ON| Working mode
Function （IR CODE TYPE）| Function （USB）
---|---
| SW-3| SW-4| Instruction| | SW-5| SW-6| Instruction
1| ON| ON| Working mode| 1| OFF| OFF| Working mode
2| ON| OFF| Updating ISP mode| 2| ON| OFF| Updating mode
3| OFF| ON| Undefined| 3| OFF| ON| Undefined
4| OFF| OFF| Undefined| 4| ON| ON| Undefined
PRODUCT HIGHLIGHTS
- Adopts advanced DSP，1/2.8 inch 2.4MP image sensor, and high quality 12X 72.5degree FOV optical lens, to output crystal clear image, max up to 1080p60 full high definition resolution.
- Fast switching between different video formats: less than 1 second.
- 12X Optical Zoom + 12XDigital Zoom.
- Fast and accurate focus performance.
- Easy firmware upgrade-(field-upgradable).
- Power via a USB3.0 port directly, with no need for the power supply adaptor, which makes deployment even more simple, a single cable enables power, video, and control.
- Effective RS232/485 serial control. Up to 128 presets.
- Compatible with the majority of videoconferencing software (UVC1.5 protocol standard).
- With powerful functional remote controller.
- IR transfer/IR pass function: except receiving the camera remote controller signal, the camera can also receive other codec’s IR remote control signal, and pass these IR control signal to the codec’s IR receiver (via VISCA IN port).
- Multi-language OSD menu: English, Chinese.
PRODUCT SPEC
| Camera | Meet+ 12 |
|---|---|
| Item Number | TLC-300-HU2-12 |
| Sensor Video System | 1/2.8-inch high-quality 2.4MP HD CMOS sensor |
HDMI ：
9201080P60/59.94/50/30/29.97/25/24
19201080I60/59.94/50
1280720P60/59.94/50/30/29.97/25
USB2.0 (Type-C)
MJPG: 19201080P60; 1280960P60; 1280720P60;
1024768P60; 800600P60; 640480P30; 320240P60
YUY2：640480P30; 320240P30
Lens Zoom| 12x optical zoom, 12x digital zoom
Focal length| f=3.92 ~ 47.32mm, F1.8 ~ F2.8
View Angle| 72.5° (wide)~ 6.3° (Tele)
Vertical viewing angle| 42.72°~3.66°
Diagonal viewing angle| 78.58°~7.42°
Minimum Object Distance| Wide: 1.0m; Tele: 1.5m
SNR| >50dB
Image parameter
Noise Reduction| 2D/3D
Minimum LUX| 0.7lux (50 IRE Max AGC,1/30, F1.8)
White Balance| Auto/Manual/Indoor/Outdoor/Push/Sodium/Fluorescent
Focus| Auto / Manual
Iris| Auto / Manual
Electronic Shutter| Auto / Manual
BLC| Supported
Mechanism
Pan Rotation Angle| -170° ~ +170°
Tilt Rotation Angle| -30° ~ +90°
Pan Rotation Speed| 0°~120°/s
Titl Rotation Speed| 0°~80°/s
Preset| 128 presets via RS232, 10 presets via remote controller
Control| RS232/RS485/USB/Remote Controller
Video Port:| USB3.0
General
Input Voltage| 5V 1000mA(via USB 3.0)/ DC:
12V 2A(via Power Adapter)
Power Consumption| DC: 12V 2A (Pmax=8W)
Operating Temperature| -10℃~ 50℃
Operating Humidity| ≤80%
Color| Silver
Camera Dimension| 220mm×190mm×173mm
Package Dimension| 32x30x31cm
Package Content| Camera, Remote Controller, RS232 cable, USB3.0 cable, Power
Supply
CAMERA INTERFACE
1. Camera Lens
2. Camera Base
3. IR Receiver Panel
4. Indicator Light| 5. Dial Switch
6. Tripod Screw Hole
7. Installation Hole
8. Power Indicator light(red)| 9. 12VDC Power Input
10. RS232(VISCA IN)Port
11. USB3.0 Port
---|---|---
CAMERA DIMENSION(MM)
IR REMOTE CONTROLLER
LED Function Instruction
Press any button and shows in red color: Current selection is to control the
camera.
Press any button and shows in green color: Current selection is to control the
codec.
Press any button and shows in blue color: Current selection is to control the
TV.
Power button
Red button: in normal work mode, short press one time, camera will enter
standby mode; short press again, the camera will start self-configuration and
go to HOME position; it will go to No.0 preset position if that was set.
Green button: Codec power button(need to learn the button coding).
Blue button: TV power button( need to learn the button coding). Focus (Left):
+/-
Manual focus, only valid under manual focus model.
Zoom (Right): +/-
Control the lens zoom rate.
Navigate : Up/Down/Left/Right
In normal working mode, use navigate key to control pan/tilt.
Confirm/Home button:
In normal working mode, short press to let the camera go back to Home
position. Menu button:
Enter the OSD menu.
Number buttons
Set Preset: Long press(3seconds) the number button to save preset.
Clear Preset: +number button to clear the relative preset.
Long press(3seconds) the Clear button to clear all preset.
Run Preset: Short press the number button to run the relative preset.
LEARNING FUNCTION：
- Press the green button, the LED indicator light will show in green color for 1 second, means switch to video terminal/codec control mode.
- Single Button Coding: long press(3seconds) Home +number”1″ button simultaneously, the green indicator LED will light, enter button learning mode, press the buttons which need to be learned, LED will start flickering(1HZ), now can start button learning: get the codec remote point to the camera remote’s infrared tube( about 10cm distance), then press the button which need to be learned, the LED re-flickering when learning finishes ; press other buttons which also need to be learned; Press the Home+”0″ buttons simultaneously to exit and save all remote data. If the button learning fails, the camera will enter normal working mode after 15seconds, LED will extinguish.
- All Button Coding: long press (3seconds) Home+number”2″ button simultaneously, the green indicator LED will start flickering(1HZ), to enter all button learning mode: get codec remote point to the camera remote’s infrared tube( about 10cm distance), to start all button coding mode, the LED will extinguish when learning finished. If the button learning fails, the camera will enter normal working mode after 15seconds, LED will extinguish.
- All Button Sending Mode: long press (3seconds) the Menu+ number “3” button simultaneously, the remote will enter all button sending mode.
- Similar operation for the TV control mode learning.
VISCA IN (RS232) PORT
| No. | Function |
|---|---|
| 1 | DTR |
| 2 | DSR |
| 3 | TXD |
| 4 | GND |
| 5 | RXD |
| 6 | A |
| 7 | IR OUT |
| 8 | B |
VISCA IN &RS485 Connection
| Camera VISCA IN | RS485 |
|---|---|
| 1 | DTR |
| 2 | DSR |
| 3 | TXD |
| 4 | GND |
| 5 | RXD |
| 6 | A(+) |
| 7 | IR OUT |
| 8 | B(-) |
VISCA IN &DB9 Connection
| Camera VISCA IN | Windows DB-9 |
|---|---|
| 1 | DTR |
| 2 | DSR |
| 3 | TXD |
| 4 | GND |
| 5 | RXD |
| 6 | A(+) |
| 7 | IR OUT |
| 8 | B(-) |
SERIAL PORT CONFIGURATION:
| Parameter | Value | Parameter | Value |
|---|---|---|---|
| Baud rate | 2400/4800/9600/115200 | Stop Bit | 1bit |
| Start Bit | 1 bit | Verify Bit | None |
| Date Bit | 8 bit |
VISCA PROTOCOL
Part 1 Camera Return Command
Ack/Completion Message
| Command Packet| Note
ACK| z0 41 FF| Returned when the command is accepted.
Completion| z0 51 FF| Returned when the command has been executed.
z = camera adderss+8
Error Messages
| Command Packet| Note
Syntax Error| z0 60 02 FF| Returned when the command format is different or
when a command with illegal command parameters is accepted
Command Not Executable| z0 61 41 FF| Returned when a command cannot be
executed due to current conditions. For example, when commands controlling the
focus manually are received during auto focus.
Part2 Camera Control Command
| Command | Function | Command Packet | Note |
|---|---|---|---|
| AddressSet | Broadcast | 88 30 01 FF | Address setting |
| IF_Clear | Broadcast | 88 01 00 01 FF | I/F Clear |
| CAM_Power | On | 8x 01 04 00 02 FF | Power ON/OFF |
| Off | 8x 01 04 00 03 FF | ||
| CAM_Zoom | Stop | 8x 01 04 07 00 FF | |
| Tele(Standard) | 8x 01 04 07 02 FF | ||
| Wide(Standard) | 8x 01 04 07 03 FF | ||
| Tele(Variable) | 8x 01 04 07 2p FF | p = 0(low)~7(high) | |
| Wide(Variable) | 8x 01 04 07 3p FF | ||
| Direct | 8x 01 04 47 0p 0q 0r 0s FF | pqrs: Zoom Position (0(wide) |
~0x4000(tele))
CAM_Focus| Stop| 8x 01 04 08 00 FF|
Far(Standard)| 8x 01 04 08 02 FF
Near(Standard)| 8x 01 04 08 03 FF
Direct| 8x 01 04 48 0p 0q 0r 0s FF| pqrs: Focus Position
One Push AF| 8x 01 04 18 01 FF|
CAM_ZoomFocus| Direct| 8x 01 04 47 0p 0q 0r 0s 0t 0u 0v 0w FF|
pqrs: Zoom Position (0(wide)~ 0x4000(tele)) tuvw: Focus Position
CAM_WB| Auto| 8x 01 04 35 00 FF|
Indoor| 8x 01 04 35 01 FF|
Outdoor| 8x 01 04 35 02 FF|
| OnePush| 8x 01 04 35 03 FF|
ATW| 8x 01 04 35 04FF|
Manual| 8x 01 04 35 05 FF|
Sodium Lamp| 8x 01 04 35 08 FF|
Fluorescent lamp| 8x 01 04 35 09 FF|
CAM_RGain| Reset| 8x 01 04 03 00 FF| Manual Control of R Gain
Up| 8x 01 04 03 02 FF
Down| 8x 01 04 03 03 FF
Direct| 8x 01 04 43 00 00 0p 0q FF| pq: R Gain (0~0xFF)
CAM_Bgain| Reset| 8x 01 04 04 00 FF| Manual Control of B Gain
Up| 8x 01 04 04 02 FF
Down| 8x 01 04 04 03 FF
Direct| 8x 01 04 44 00 00 0p 0q FF| pq: B Gain (0-0xFF)
CAM_AE| Full Auto| 8x 01 04 39 00 FF| Automatic Exposure mode
Manual| 8x 01 04 39 03 FF| Manual Control mode
Shutter Priority| 8x 01 04 39 0A FF| Shutter Priority mode
Iris Priority| 8x 01 04 39 0B FF| Iris Priority mode
Bright| 8x 01 04 39 0D FF| Bright mode(Manual control)
CAM_Shutter| Reset| 8x 01 04 0A 00 FF| Shutter Setting
Up| 8x 01 04 0A 02 FF
Down| 8x 01 04 0A 03 FF
Direct| 8x 01 04 4A 00 00 0p 0q FF| pq: Shutter Position (0~0x15)
CAM_Iris| Reset| 8x 01 04 0B 00 FF| Iris Setting
Up| 8x 01 04 0B 02 FF
Down| 8x 01 04 0B 03 FF
Direct| 8x 01 04 4B 00 00 0p 0q FF| pq: Iris Position (0~ 0x11)
CAM_Gain| Reset| 8x 01 04 0C 00 FF| Gain Setting
Up| 8x 01 04 0C 02 FF
Down| 8x 01 04 0C 03 FF
Direct| 8x 01 04 0C 00 00 0p 0q FF| pq: Gain Positon (0~0x0E)
CAM_Bright| Reset| 8x 01 04 0D 00 FF| Bright Setting
| Up| 8x 01 04 0D 02 FF|
Down| 8x 01 04 0D 03 FF
Direct| 8x 01 04 4D 00 00 0p 0q FF| pq: Bright l Positon ()
CAM_WDR| On| 8x 01 04 3D 02 FF| WDR ON/OFF
Off| 8x 01 04 3D 03 FF
Direct| 8x 01 04 D3 0p FF| pq: WDR Position (1~0x06)
CAM_BackLight| On| 8x 01 04 33 02 FF| BackLight On
Off| 8x 01 04 33 03 FF| BackLight Off
CAM_Sharpness| Reset| 8x 01 04 02 00 FF| Sharpness Control
Up| 8x 01 04 02 02 FF
Down| 8x 01 04 02 03 FF
Direct| 8x 01 04 42 00 00 0p 0q FF| pq: Aperture Gain (0~0x04)
CAM_Preset| Reset| 8x 01 04 3F 00 0p FF| p: Preset Number(=0 to 127)
Corresponds to 0 to 9 on the Remote Commander
Set| 8x 01 04 3F 01 0p FF
Recall| 8x 01 04 3F 02 0p FF
CAM_LR_Reverse| On| 8x 01 04 61 02 FF| Image Flip Horizontal ON/OFF
Off| 8x 01 04 61 03 FF
CAM_PictureFlip| On| 8x 01 04 66 02 FF| Image Flip Vertical ON/OFF
Off| 8x 01 04 66 03 FF
CAM_MountMode| UP| 8x 01 04 A4 02 FF| Mount Up
Down| 8x 01 04 A4 03 FF| Mount Down
CAM_Saturation| Direct| 8x 01 04 A1 00 00 00 0p FF| (0~0x0E)
CAM_2D Noise Reduction| Direct| 8x 01 04 53 0p FF| (0~0x05)
CAM_3D Noise Reduction| Direct| 8x 01 04 54 0p FF| (0~0x03)
CAM_NewBright| Direct| 81 01 04 A4 00 00 0p 0q FF| (0~0x0F)
CAM_Constrast| Direct| 81 01 04 A2 00 00 0p 0q FF| (0~0x0F)
CAM_Gamma| Direct| 8x 01 04 5B 0p FF| (0~0x04)
FLICK| Off| 81 01 04 23 00 FF|
50HZ| 81 01 04 23 01 FF|
60HZ| 81 01 04 23 02 FF|
SYS_Menu| Menu On| 8x 01 06 06 02 FF| Turn on the menu
| Menu Off| 8x 01 06 06 03 FF| Turn off the menu
IR_Transfer| Transfer On| 8x 01 06 1A 02 FF| Receive IR(remote commander) CODE
from VISCA communication ON/OFF
Transfer Off| 8x 01 06 1A 03 FF
IR_Receive| On| 8x 01 06 08 02 FF| IR(remote commander)receive ON/OFF
Off| 8x 01 06 08 03 FF
On/Off| 8x 01 06 08 10 FF
Pan_tiltDrive| Up| 8x 01 06 01 VV WW 03 01 FF| VV: Pan speed 0x01 (low speed)
to 0x18 (high speed) WW: Tilt speed 0x01 (low speed) to 0x14 (high speed)
YYYY: Pan Position(TBD) ZZZZ: Tilt Position(TBD)
Down| 8x 01 06 01 VV WW 03 02 FF
Left| 8x 01 06 01 VV WW 01 03 FF
Right| 8x 01 06 01 VV WW 02 03 FF
Upleft| 8x 01 06 01 VV WW 01 01 FF
Upright| 8x 01 06 01 VV WW 02 01 FF
DownLeft| 8x 01 06 01 VV WW 01 02 FF
DownRight| 8x 01 06 01 VV WW 02 02 FF
Stop| 8x 01 06 01 VV WW 03 03 FF
AbsolutePositio n| 8x 01 06 02 VV WW 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
RelativePosition| 8x 01 06 03 VV WW
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
Home| 8x 01 06 04 FF
Reset| 8x 01 06 05 FF
Pan-tiltLimitSet| Set| 8x 01 06 07 00 0W
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF| W:1 UpRight 0:DownLeft YYYY: Pan Limit
Position(TBD) ZZZZ: Tilt Limit Position(TBD)
Part3 Inquiry Command
| Command | Command Packet | Return Packet | Note |
|---|---|---|---|
| CAM_PowerInq | 8x 09 04 00 FF | y0 50 02 FF | On |
| y0 50 03 FF | Off(Standby) | ||
| CAM_ZoomPosInq | 8x 09 04 47 FF | y0 50 0p 0q 0r 0s FF | pqrs: Zoom Position |
| CAM_FocusModeInq | 8x 09 04 38 FF | y0 50 02 FF | Auto Focus |
| y0 50 03 FF | Manual Focus | ||
| CAM_FocusPosInq | 8x 09 04 48 FF | y0 50 0p 0q 0r 0s FF | pqrs: Focus Position |
| --- | --- | --- | --- |
| CAM_WBModeInq | 8x 09 04 35 FF | y0 50 00 FF | Auto |
| y0 50 01 FF | Indoor mode | ||
| y0 50 02 FF | Outdoor mode | ||
| y0 50 03 FF | OnePush mode | ||
| y0 50 04 FF | ATW | ||
| y0 50 05 FF | Manual | ||
| CAM_RGainInq | 8x 09 04 43 FF | y0 50 00 00 0p 0q FF | pq: R Gain |
| CAM_BGainInq | 8x 09 04 44 FF | y0 50 00 00 0p 0q FF | pq: B Gain |
| CAM_AEModeInq | 8x 09 04 39 FF | y0 50 00 FF | Full Auto |
| y0 50 03 FF | Manual | ||
| y0 50 0A FF | Shutter priority | ||
| y0 50 0B FF | Iris priority | ||
| y0 50 0D FF | Bright | ||
| CAM_ShutterPosInq | 8x 09 04 4A FF | y0 50 00 00 0p 0q FF | pq: Shutter Position |
| CAM_IrisPosInq | 8x 09 04 4B FF | y0 50 00 00 0p 0q FF | pq: Iris Position |
| CAM_GainPosiInq | 8x 09 04 4C FF | y0 50 00 00 0p 0q FF | pq: Gain Position |
| CAM_ BrightPosiInq | 8x 09 04 4D FF | y0 50 00 00 0p 0q FF | pq: Bright Position |
| CAM_ExpCompModeInq | 8x 09 04 3E FF | y0 50 02 FF | On |
| y0 50 03 FF | Off | ||
| CAM_ExpCompPosInq | 8x 09 04 4E FF | y0 50 00 00 0p 0q FF | pq: ExpComp Position |
| CAM_ApertureInq | 8x 09 04 42 FF | y0 50 00 00 0p 0q FF | pq: Aperture Gain |
| CAM_MemoryInq | 8x 09 04 3F FF | y0 50pp FF | pp: Memory number last operated. |
| SYS_MenuModeInq | 8x 09 06 06 FF | y0 50 02 FF | On |
| y0 50 03 FF | Off | ||
| CAM_LR_ReverseInq | 8x 09 04 61 FF | y0 50 02 FF | On |
| y0 50 03 FF | Off | ||
| CAM_PictureFlipInq | 8x 09 04 66 FF | y0 50 02 FF | On |
| y0 50 03 FF | Off | ||
| CAM_VersionInq | 8x 09 00 02 FF | y0 50 ab cd mn pq rs tu vw FF | |
| IR_Transfer | 8x 09 06 1A FF | y0 50 02 FF | On |
| y0 50 03 FF | Off | ||
| IR_Receive | 8x 09 06 08 FF | y0 50 02 FF | On |
| y0 50 03 FF | Off | ||
| IR_ReceiveReturn | y0 07 7D 01 04 00 FF | Power ON/OFF | |
| y0 07 7D 01 04 07 FF | Zoom tele/wide | ||
| y0 07 7D 01 04 38 FF | AF On/Off | ||
| --- | --- | --- | --- |
| y0 07 7D 01 04 33 FF | CAM_Backlight | ||
| y0 07 7D 01 04 3F FF | CAM_Memory | ||
| y0 07 7D 01 06 01 FF | Pan_tiltDrive | ||
| Pan-tiltPosInq | 8x 09 06 12 FF | y0 50 0w 0w 0w 0w 0z 0z 0z 0z FF |
wwww:PanPosition zzzz: Tilt Position
Note:【x】 means the camera address ;【y】=【x + 8】.
VISCA PAN TILT ABSOLUTE POSITION VALUE
| Pan Angle | VISCA Value | Tilt Angle | VISCA Value |
|---|---|---|---|
| -170 | 0xF670 | -30 | 0xFE50 |
| -135 | 0xF868 | 0 | 0x0000 |
| -90 | 0xFAF0 | 30 | 0x01B0 |
| -45 | 0xFD78 | 60 | 0x0360 |
| 0 | 0x0000 | 90 | 0x510 |
| 45 | 0x0288 | ||
| 90 | 0x0510 | ||
| 135 | 0x0798 | ||
| 170 | 0x0990 |
VISCA PAN TILT SPEED VALUE
| Pan(degree/second) | tilt(degree/second) |
|---|---|
| 0 | 0.3 |
| 1 | 1 |
| 2 | 1.5 |
| 3 | 2.2 |
| 4 | 2.4 |
| 5 | 2.6 |
| 6 | 2.8 |
| 7 | 3.0 |
| 8 | 3.2 |
| 9 | 3.4 |
| 10 | 3.8 |
| 11 | 4.5 |
| 12 | 6 |
| 13 | 9 |
| 14 | 15 |
| 15 | 19 |
| 16 | 25 |
| 17 | 32 |
| 18 | 38 |
| 19 | 45 |
| 20 | 58 |
| 21 | 75 |
| 22 | 88 |
| 23 | 105 |
| 24 | 120 |
| Shutter speed | |
| --- | --- |
| 21 | 1/10000 |
| 20 | 1/6000 |
| 19 | 1/4000 |
| 18 | 1/3000 |
| 17 | 1/2000 |
| 16 | 1/1500 |
| 15 | 1/1000 |
| 14 | 1/725 |
| 13 | 1/500 |
| 12 | 1/350 |
| 11 | 1/250 |
| 10 | 1/180 |
| 9 | 1/125 |
| 8 | 1/100 |
| 7 | 1/90 |
| 6 | 1/60 |
| 5 | 1/30 |
| 4 | 1/15 |
| 3 | 1/8 |
| 2 | 1/4 |
| 1 | 1/2 |
| 0 | 1/1 |
| Gain | 0 |
| 1 | 2dB |
| 2 | 4dB |
| 3 | 6dB |
| 4 | 8dB |
| 5 | 10dB |
| 6 | 12dB |
| 7 | 14dB |
PELCO-D PROTOCOL
Function| Byte1| Byte2| Byte 3| Byte 4| Byte5|
Byte6| Byte 7
---|---|---|---|---|---|---|---
Up| 0xFF| Address| 0x00| 0x08| Pan Speed| Tilt Speed| SUM
Down| 0xFF| Address| 0x00| 0x10| Pan Speed| Tilt Speed| SUM
Left| 0xFF| Address| 0x00| 0x04| Pan Speed| Tilt Speed| SUM
Right| 0xFF| Address| 0x00| 0x02| Pan Speed| Tilt Speed| SUM
Upleft| 0xFF| Address| 0x00| 0x0C| Pan Speed| Tilt Speed| SUM
Upright| 0xFF| Address| 0x00| 0x0A| Pan Speed| Tilt Speed| SUM
DownLeft| 0xFF| Address| 0x00| 0x14| Pan Speed| Tilt Speed| SUM
DownRight| 0xFF| Address| 0x00| 0x12| Pan Speed| Tilt Speed| SUM
Zoom In| 0xFF| Address| 0x00| 0x20| 0x00| 0x00| SUM
Zoom Out| 0xFF| Address| 0x00| 0x40| 0x00| 0x00| SUM
Focus Far| 0xFF| Address| 0x00| 0x80| 0x00| 0x00| SUM
Focus Near| 0xFF| Address| 0x01| 0x00| 0x00| 0x00| SUM
Set Preset| 0xFF| Address| 0x00| 0x03| 0x00| Preset ID| SUM
Clear Preset| 0xFF| Address| 0x00| 0x05| 0x00| Preset ID| SUM
Call Preset| 0xFF| Address| 0x00| 0x07| 0x00| Preset ID| SUM
Query Pan Position| 0xFF| Address| 0x00| 0x51| 0x00| 0x00| SUM
Query Pan Position Response| 0xFF| Address| 0x00| 0x59| Value High Byte| Value
Low Byte| SUM
Query Tilt Position| 0xFF| Address| 0x00| 0x53| 0x00| 0x00| SUM
Query Tilt Position Response| 0xFF| Address| 0x00| 0x5B| Value High Byte|
Value Low Byte| SUM
Query Zoom Position| 0xFF| Address| 0x00| 0x55| 0x00| 0x00| SUM
Query Zoom Position Response| 0xFF| Address| 0x00| 0x5D| Value High Byte|
Value Low Byte| SUM
PELCO-P PROTOCOL
Function| Byte 1| Byte2| Byte 3| Byte 4| Byte5|
Byte6| Byte7| Byte 8
---|---|---|---|---|---|---|---|---
Up| 0xA0| Addres s| 0x00| 0x08| Pan Speed| Tilt Speed| 0xAF| XOR
Down| 0xA0| Addres s| 0x00| 0x10| Pan Speed| Tilt Speed| 0xAF| XOR
Left| 0xA0| Addres s| 0x00| 0x04| Pan Speed| Tilt Speed| 0xAF| XOR
Right| 0xA0| Addres s| 0x00| 0x02| Pan Speed| Tilt Speed| 0xAF| XOR
Upleft| 0xA0| Addres s| 0x00| 0x0C| Pan Speed| Tilt Speed| 0xAF| XOR
Upright| 0xA0| Addres s| 0x00| 0x0A| Pan Speed| Tilt Speed| 0xAF| XOR
DownLeft| 0xA0| Addres s| 0x00| 0x14| Pan Speed| Tilt Speed| 0xAF| XOR
DownRight| 0xA0| Addres s| 0x00| 0x12| Pan Speed| Tilt Speed| 0xAF| XOR
Zoom In| 0xA0| Addres s| 0x00| 0x20| 0x00| 0x00| 0xAF| XOR
Zoom Out| 0xA0| Addres s| 0x00| 0x40| 0x00| 0x00| 0xAF| XOR
Focus Far| 0xA0| Addres s| 0x00| 0x80| 0x00| 0x00| 0xAF| XOR
Focus Near| 0xA0| Addres s| 0x01| 0x00| 0x00| 0x00| 0xAF| XOR
Set Preset| 0xA0| Addres s| 0x00| 0x03| 0x00| Preset ID| 0xAF| XOR
Clear Preset| 0xA0| Addres s| 0x00| 0x05| 0x00| Preset ID| 0xAF| XOR
Call Preset| 0xA0| Addres s| 0x00| 0x07| 0x00| Preset ID| 0xAF| XOR
Query Pan Position| 0xA0| Addres s| 0x00| 0x51| 0x00| 0x00| 0xAF| XOR
Query Pan Position Response| 0xA0| Addres s| 0x00| 0x59| Value
High Byte| Value Low Byte| 0xAF| XOR
Query Tilt Position| 0xA0| Addres s| 0x00| 0x53| 0x00| 0x00| 0xAF| XOR
Query Tilt Position Response| 0xA0| Addres s| 0x00| 0x5B|
Value High Byte| Value Low Byte| 0xAF| XOR
Query Zoom Position| 0xA0| Addres s| 0x00| 0x55| 0x00| 0x00| 0xAF| XOR
Query Zoom Position Response| 0xA0| Addres s| 0x00| 0x5D|
Value High Byte| Value Low Byte| 0xAF| XOR
OSD MENU
-
under working mode, press the menu button on the IR remote, to enter the OSD menu .
-
Use the navigate button to select the main menu. Once been selected, the main menu will change to grey color background, and the right side will show all parameters under this sub menu :
-
Press the right navigate button to enter sub menu, use up and down navigate button to select parameter.
-
Press the menu button again to return to previous menu; Press it continuously to exit the OSD menu.
Before exiting, will show up a window to remind whether need to save all settings ( use left and right button to set). -
OSD Menu List& Defaulted Setting
CAMERA SET| LANGUAGE| ENGLISH/CHINESE|
---|---|---|---
PROTOCOL| VISCA/PELCO-P/PELCO-D| VISCA
ADDRESS| VISCA:1~7 PELCO-P/D:1~7| 1
BAUD RATE| 2400/9600/115200| 9600
PARITY BIT| NONE|
RETURN| Return to previous menu|
VIDEO MODE| It will cause video freeze if switch video mode via OSD menu;
Only recommend to change video mode via UVC control.
---|---
RETURN| Return to previous menu
FOCUS| FOCUS MODE| AUTO/MANU/PUSH| AUTO
---|---|---|---
SENSITIVITY| Focus Sensitivity setting: LOW/MID/HIGH| MID
FOCUS LIMIT| The target distance: 1.5M/2M/3M/6M/10M| 1.5M
D_ZOOM| Digital Zoom: OFF/ON| OFF
ZOOM SPEED| Set zoom speed level:0~7| 7
LENS INIT| Lens focus parameter frequency setting, choose EXE to start the
lens focus reset| OFF
DIS ZOOM RATIO| Display zoom value during zooming control| OFF
RETURN| Return to previous menu|
WB MODE| WB MODE| Set White Balance mode| ATW
---|---|---|---
B_GAIN| Set blue gain under manual mode| 52
R_GAIN| Set red gain under manual mode| 58
RETURN| Return to previous menu|
EXPOSURE| EXP MODE| AUTO、MANU、BRI.、SHUT、IRIS| AUTO
---|---|---|---
SHUT TIME| Set shutter speed: 1/1~1/10000, Only available under MANU or SHUT
mode| 1/100
IRIS| Set iris value: 0~13, only available under MANU or IRIS mode| 10
GAIN| Set gain value: 0~15, only available under MANU mode| 0
BRIGHT| Set bright value: 0~27 , only available under MANU mode| 11
SLOW SHUT| Slow shutter set: OFF/ON| OFF
FLICK| 50HZ/60HZ/OFF| 50Hz
RETURN| Return to previous menu|
PICTURE| BRIGHTNESS| Set brightness value: 0~15| 8
---|---|---|---
SHARPNESS| Set sharpness value: 0~63| 40
CONSTRAST| Set contrast value: 0~63| 32
| SATURATION| Set saturation value: 0~63, the higher value, the stronger
color| 40
---|---|---|---
MIRROR| Left/right flip: ON/OFF| OFF
PIC FLIP| Up/down flip: ON/OFF| OFF
FREEZE| ON/OFF| OFF
DEFOG| Set image permeability| OFF
RETURN| Return to previous menu|
IMAGE ENHANC E| 2D NR| ON/OFF| OFF
---|---|---|---
3D NR| OFF/AUTO/1~4| AUTO
D_WDR| Set dynamic level : OFF/1~6| OFF
GAMMA| Set gamma: 0~4| 0
BACKLIGHT| ON/OFF| OFF
HIGHLIGHT| ON/OFF| OFF
RETURN| Return to previous menu|
MASK| MASK SWITCH| Privacy zone function: ON/OFF| OFF
---|---|---|---
COLOUR| Set mask zone color: WHITE/YELLOW/GRAY/GREEN/VIOLET/RED| WHITE
INDEX| Set mask zone number: 1~8| 1
INDEX SWITCH| Set index zone: ON/OFF| OFF
ROW START| Set current mask zone’s row start position| 0
ROW END| Set current mask zone’s row end position| 479
LINE START| Set current mask zone’s line start position| 0
LINE END| Set current mask zone’s line end position| 539
RETURN| Return to previous menu|
D/N MODE| D/N MODE| Set D/N mode: DAY/NIGHT/AUTO| DAY
---|---|---|---
DAY TO NIGHT| Set day to night brightness threshold value: 15~200| 49
NIGH TO DAY| Set night to day brightness threshold value: 5~190| 20
SWITCH DELAY| Set switch delay between different mode, to avoid repeat
switching under AUTO mode: 1~60s| 5
GAIN LIMIT| Gain limit under low light:2/4/6/8/11/16/32/64/128/256/320/511|
511
RETURN| Return to previous menu|
D/N MODE| D/N MODE| Set D/N mode: DAY/NIGHT/AUTO| DAY
---|---|---|---
DAY TO NIGHT| Set day to night brightness threshold value: 15~200| 49
NIGH TO DAY| Set night to day brightness threshold value: 5~190| 20
SWITCH DELAY| Set switch delay between different mode, to avoid repeat
switching under AUTO mode: 1~60s| 5
GAIN LIMIT| Gain limit under low light:2/4/6/8/11/16/32/64/128/256/320/511|
511
RETURN| Return to previous menu|
RESET| REEST to defaulted value (except the Language): ON/OFF
---|---
UVC CONTROL
- Only run the client software after the USB3.0 camera has completed self-configuration(the IR indicator in blue color and will not flash); otherwise may cause black video issue.
- Make sure the USB3.0 camera is recognized by the PC Device Manager.
- Make sure the interval of video format switching more than 1 seconds, otherwise black video maybe caused.
- Make sure the interval of control command sending from the server(via USB) to the camera no less than 250ms.
- Support standard UVC interface.
UVC Property| Corresponded VISCA
Command
---|---
PU_BACKLIGHT_COMPENSATION_CONTROL| 8x 01 04 33 02 FF
CY_FX_UVC_PU_BRIGHTNESS_CONTROL| 8x 01 04 A4 00 00 0p 0q FF
CY_FX_UVC_PU_CONTRAST_CONTROL| 8x 01 04 A2 00 00 0p 0q FF
CY_FX_UVC_PU_SATURATION_CONTROL| 8x 01 04 A1 00 00 0p 0q FF
CY_FX_UVC_PU_SHARPNESS_CONTROL| 8x 01 04 42 00 00 0p 0q FF
CY_FX_UVC_PU_GAMMA_CONTROL| 8x 01 04 5B 0p FF
CY_FX_UVC_PU_WHITE_BALANCE_TEMPERATURE_CONTROL| 8x 01 04 35 0p FF
CY_FX_UVC_PU_BACKLIGHT_COMPENSATION_CONTROL| 8x 01 04 33 0p FF
CY_FX_UVC_PU_GAIN_CONTROL| 8x 01 04 49 00 00 0p 0q FF
CY_FX_UVC_PU_POWER_LINE_FREQUENCY_CONTROL| 8x 01 04 AA 0p FF
PU_GAIN_CONTROL| 8x 01 04 49 00 00 00 0p FF
CT_ZOOM_ABSOLUTE_CONTROL| 8x 01 04 47 0p 0q 0r 0s FF
CT_PANTILT_ABSOLUTE_CONTROL| 8x 01 06 02 VV WW 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
CT_PANTILT_RELATIVE_CONTROL| 8x 01 06 01 pp qq rr ss FF
CT_ZOOM_RELATIVE_CONTROL| 8x 01 04 07 pp FF
6 Floor, Building A, Shuanghuan Information Technology Industrial Park, No.8,
Baoqing Rd, Longgang District, Shenzhen, 518116, China
+86 755 33275155
https://www.telycam.com