telycam TLC-300-IP 12NDI FHD PTZ Video Camera User Manual

June 13, 2024
Telycam

telycam-logo

telycam TLC-300-IP 12NDI FHD PTZ Video Camera

telycam-TLC-300-IP-12NDI-FHD-PTZ-Video-Camera-product

Product Information

  • Product Name: 12X NDI FHD PTZ Video Camera
  • User Manual Version: V4.0 English
  • Model Number: J.BC.0205.0099

Safety Guides
Note: The video quality may be affected by the specific frequencies of electromagnetic field. Never grasp the head of the camera, and never move the camera by hand when it is working, otherwise, mechanism maybe destroyed.

Packing List
QUICK START

  1. Check all cable connections before power on.
  2. Dial Switch Setting (at the bottom of the camera):
Dial Switch SW-3 SW-4
Instruction 1 OFF OFF reserve
2 ON OFF reserve
3 OFF ON reserve
4 ON ON reserve

Product Highlights
Camera Specifications:
Video Format: HDMI, SDI, USB, IP, NDI

Supported Video Resolutions:
1920x1080P60/50/30/25/59.94/29.97/24, 1920x1080i60/50/59.94,
1280x720P60/50/30/25/59.94/29.97

Sensor: 1/2.8 2.4MP CMOS sensor
Zoom: Yes
Rotation Angle: Adjustable
Rotation Speed: Adjustable
Preset: Yes
Control Port: RS232, RS485, NDI|HX(VISCA over IP), USB3.0(UVC1.5), USB2.0(UVC1.1)

Network and Other Features:

  • Network Speed: Adjustable
  • Video Encode Bit Rate Control: Yes
  • Video Bit Rate: Adjustable
  • Supported Protocol: POE+, NDI, Daisy Chain
  • Minimum Lux: Adjustable
  • White Balance: Adjustable
  • Exposure: Adjustable
  • Focus: Adjustable
  • Iris: Adjustable
  • Electric Shutter: Adjustable
  • Gamma: Adjustable
  • WDR: Yes
  • BLC: Yes
  • 2D Noise Reduction : Yes
  • 3D Noise Reduction: Yes
  • Anti Flicker: Yes
  • Pan Tilt Flip: Yes
  • Input Voltage: Adjustable
  • Dimension: Adjustable
  • Net Weight: Adjustable

Camera Interface

  1. Camera Lens
  2. Camera Base
  3. IR Receiver Panel
  4. Power Indicator Light
  5. Dial Switch
  6. Tripod Screw Hole
  7. Installation Hole
  8. RS232 control port (input)
  9. RS232 control port (output)
  10. HDMI port
  11. 3G-SDI port
  12. Line in port
  13. NDI|HX port
  14. DC12V plug

IR Remote Controller
SET 1~SET4 ADDRESS SETTING: Long press for 3
seconds until the key light ON, to set camera address.

CAM1~CAM4 (CAMERA SELECTING): Short press to
select the relative camera.

NUMBER KEY (1-9): Set preset: long press (3 seconds) the number key to set preset. Run preset: Short press the number key to run preset. CLR PRE (CLEAR PRESET) CLR PRE+ number key: to clear the relative preset. Long press to clear all preset.

FOCUS KEY (ON THE LEFT): Manual focus, only valid under manual focus model.

ZOOM KEY (ON THE RIGHT SIDE): Set the zoom rate.

NAVIGATE KEY: UP/DOWN/LEFT/RIGHT Under working mode, use navigate key to set the pan tilt, and select menu when enter OSD.

OK /HOME KEY: Under working mode, short press OK to make the camera go back to HOME position; and confirm the selection when enter OSD.

AF: Auto Focus.
MF: Manual Focus.
RESET: Press 3 seconds to reset camera.
MENU: Enter OSD menu.
LEARN+LIMIT L key: Set the pan tilt left limit position.
LEARN+LIMIT R key: Set the pan tilt right limit position.
LEARN+LMT CLR key: Clear the limit position.

Product Usage Instructions

  1. Before powering on the camera, ensure all cable connections are properly checked.
  2. At the bottom of the camera, adjust the dial switches based on the provided instructions.
  3. To set camera address, long press the desired SET 1~SET4 ADDRESS SETTING key on the IR remote controller for 3 seconds until the key light turns on.
  4. To select the camera, short press the corresponding CAM1~CAM4 key on the IR remote controller.
  5. To set a preset, long press the desired NUMBER KEY (1-9) on the IR remote controller for 3 seconds. To run a preset, short press the corresponding NUMBER KEY.
  6. To clear a preset, press CLR PRE+ number key on the IR remote controller. To clear all presets, long press CLR PRE.
  7. To manually focus, use the FOCUS KEY on the left side of the IR remote controller. This is only valid under manual focus mode.
  8. To set the zoom rate, use the ZOOM KEY on the right side of the IR remote controller.
  9. Under working mode, use the NAVIGATE KEY (UP/DOWN/LEFT/RIGHT) to set the pan tilt and navigate through the OSD menu.
  10. Under working mode, short press the OK /HOME KEY to make the camera go back to the HOME position and confirm selections in the OSD menu.
  11. Other functions like Auto Focus, Manual Focus, camera reset, entering OSD menu, setting pan tilt limits, and clearing limit positions can be performed using the corresponding keys on the IR remote controller.

SAFETY GUIDES

  1. Before operation, please fully read and follow all instructions in the manual. For your safety, always keep this manual with the camera.
  2. The camera power input range is 100-240V AC(50-60Hz),ensure the power supply input within this rate before powering on.
  3. The camera power voltage is 12V DC, rated currency is 2A. We suggest you use it with the original power supply adapter supplied by the factory.
  4. Please keep the power cable, video cable and control cable in a safe place. Protect all cables especially the connectors.
  5. Operational environment: 0℃-50℃, humidity less than 90%.To avoid any danger, do not put anything inside the camera, and keep away from the corrosive liquid.
  6. Avoid stress, vibration and damp during transportation, storage and installation.
  7. Do not detect the camera housing and cover. For any service, please contact authorized technicians.
  8. Video cable and control cable should be individually shielded, and cannot be substituted with other cables. Do not direct the camera lens towards strong light, such as the sun or the intensive light.
  9. Use a dry and soft cloth to clean the camera housing. Applied with neutral cleaning agent when there is need to clean. To avoid damage on the camera lens, never use strong or abrasive cleaning agents on the camera housing.
  10. Do not move the camera by holding the camera head. To avoid mechanical trouble, do not rotate the camera head by hand. NEVER MOVE THE CAMERA MANUALLY WHEN IT IS WORKING.
  11. Put the camera on fixed and smooth desk or platform, avoid leaned installation.
  12. Power Supply Polarity (Drawing)

Note:
The video quality may be affected by the specific frequencies of electromagnetic field.
Never grasp the head of the camera, and never move the camera by hand when it is working, otherwise, mechanism maybe destroyed.

telycam-TLC-300-IP-12NDI-FHD-PTZ-Video-Camera- \(2\)

PACKING LIST

Check all bellow items when open the package:

  • Camera····················································································· 1
  • Power Adapter ············································································ 1
  • Power Cable ·············································································· 1
  • RS232 Control Cable ···································································· 1
  • USB3.0 Cable ············································································ 1
  • Remote Controller ······································································· 1
  • User Manual ·············································································· 1
  • Double-sided Adhesive ·································································· 1
  • QC certification ·········································································· 1

QUICK START

  • Check all cable connections before power on.telycam-TLC-300-IP-12NDI-FHD-PTZ-Video-Camera- \(1\)
  • Dial Switch Setting (at the bottom of the camera):

Dial Switch

| SW-3| SW-4| Instruction
1| OFF| OFF| reserve
2| ON| OFF| reserve
3| OFF| ON| reserve
4| ON| ON| reserve
Dial Switch (ARM)

| SW-1| SW-2| Instruction
1| OFF| OFF| Updating mode
2| ON| OFF| Debugging mode
3| OFF| ON| Undefined
4| ON| ON| Working mode
Dial Switch (USB)

| SW-5| SW-6| Instruction
1| OFF| OFF| Updating mode
2| ON| OFF| Working mode
3| OFF| ON| Undefined
4| ON| ON| Undefined

PRODUCT HIGHLIGHTS

  • Adopts most advanced ISP, 1/2.8 inch 2.4MP sensor, providing 1080P60 full HD video resolution.
  • Standard wide angle optical lens: 12x optical zoom , with 72.5 degree field of view.
  • 1080p60 video over IP, H.264, H.265 encoding.
  • Support NewTek NDI V4.5 video transmission and control.
  • NDI|HX, HDMI, 3G-SDI, USB outputs, fit for different application.
  • White Balance, Exposure, Focus, Iris can be adjusted automatically or manually.
  • Support POE: one single CAT5/6 to get video, control and power supply.
  • Special Focusing Algorithm: fast and precise focusing performance when zooming or moving.
  • Smooth PTZ mechanical design, accurate pan tilt motor control.
  • 128 presets supported; Exposure parameter and white balance parameter can be saved in presets (in manual mode).
  • Standard Sony VISCA, IP VISCA, PELCO-P, PELCO-D control protocol; IP VISCA over both TCP and UDP.
  • Daisy chain supported, max 7 cameras connected in VISCA protocol.
  • Image flip function, support upside-down installation.
  • Fast video format switch: less than 3 seconds.
  • Supported field upgrade for ISP, ARM, FPGA and USB.
  • USB3.0 port compatible with USB2.0 output.
  • Support RS232/RS485/UVC control.
  • Standard UVC1.5 protocol, seamlessly compatible with major video conferencing software and platform.
  • OSD menu in English and Chinese supported. IP address, streaming resolution and size can be set in OSD menu.

CAMERA SPEC

| | 19201080P60/50/30/25/59.94/29.97/24
---|---|---
| HDMI| 1920
1080i60/50/59.94
| | 1280720P60/50/30/25/59.94/29.97
| | 1920
1080P60/50/30/25/59.94/29.97/24
| SDI| 19201080I60/50/59.94
| | 1280
720P60/50/30/25/59.94/29.97
| | 19201080P60/50/30/25(USB3.0)
| | 1280
720P60/50/30(USB3.0)
| | 1280720P25(USB3.0&USB2.0)
Video Format| USB| 1024
576P30(USB3.0&USB2.0)
| | 960540P30(USB2.0)
| | 640
360P30(USB2.0)
| | 512288P30(USB2.0)
| IP| Main Stream: 1920
1080@3~60; 1280720@3~60; 1024576@3~60
| Sub Stream: 1280720@3~60; 1024576@3~60; 640360@3~60
| | 1920
1080@3~60;
| NDI| 1280*720@3~60;

1024*576@3~60;

| | 640*360@3~60 (low bandwidth mode)
Video Interface| HDMI, SDI, NDI|HX, USB3.0,USB2.0
Sensor| 1/2.8”2.4MP CMOS sensor
Zoom| f 3.92~47.32mm(12X), F1.8- 2.8, View Angle: 72.5°(Far) -6.3°(Near)
Rotation Angle| Pan: -170°~ +170°;| Tilt: -30°~ +90°
Rotation Speed| Pan: 0°~120°/s ;| Tilt: 0°~80°/s
Preset:| Remote controller: 10; RS232: 128; Accuracy: 0.1°
Control Port| RS232, RS485, NDI|HX(VISCA over IP), USB3.0(UVC1.5), USB2.0(UVC1.1)
Network Speed| 1000M
Video encode| H.264/H.265
Bit Rate Control| Variable Bit Rate, Constant Bit Rate
Video Bit Rate| 1024Kbps~16384Kbps
Supported Protocol| TCP/IP, HTTP, RTSP, DHCP, RTMP, Onvif, NDI(V4.5), VISCA over IP(TCP&UDP), HTML5, VISCA, PELCO P/D
POE+| Supported
NDI| Supported
Daisy Chain| Support RS232 serial daisy chain
Minimum Lux| 0.1lux
White Balance| ATW/Manual/Auto/Indoor/Outdoor/Push
Exposure| Auto/Manual/Shutter/Iris/Bright
Focus| Auto/Manual
Iris| Auto/Manual
Electric Shutter| Auto/Manual
Gamma| Supported
WDR| Supported
BLC| Supported
2D Noise Reduction| Supported
3D Noise Reduction| Supported
Anti Flicker| OFF/50Hz/60Hz
Pan Tilt Flip| Supported
Input Voltage| DC12V/POE+(IEEE802.3at)
Dimension| 220mm×190mm×173mm
Net Weight| 1.40kg
| | |

CAMERA INTERFACE

telycam-TLC-300-IP-12NDI-FHD-PTZ-Video-Camera- \(3\)

  1. Camera Lens
  2. Camera Base
  3. IR Receiver Panel
  4. Power Indicator Light
  5. Dial Switch
  6. Tripod Screw Hole
  7. Installation Hole
  8. RS232 control port (input)
  9. RS232 control port(output)
  10. HDMI port
  11. 3G-SDI port
  12. Line in port
  13. NDI|HX port
  14. DC12V plug

CAMERA DIMENSION(MM)

telycam-TLC-300-IP-12NDI-FHD-PTZ-Video-Camera- \(4\)

IR REMOTE CONTROLLER

telycam-TLC-300-IP-12NDI-FHD-PTZ-Video-Camera- \(5\)

POWER
Under normal working mode, short press POWER key, to enter standby mode.
Press it again, the camera will do self-configuration, then go back to HOME position. It will go to preset position if power on model has been set before.

FREEZE (Not Supported in USB)
Short press FREEZE key to freeze/ unfreeze the image.

IRT (IR Transfer/IR Pass)
Open / close the IR pass function. Once press the IRT key, the camera will receive and Pass the IR remote control signal to the codec/terminal (via VISCA IN port).

SET 1~SET4 ADDRESS SETTING
Long press for 3seconds until the key light ON, to set camera address.

CAM1~CAM4 (CAMERA SELECTING)
Short press to select the relative camera.

NUMBER KEY (1-9)
Set preset: long press (3 seconds) the number key to set preset. Run preset: Short press the number key to run preset.

CLR PRE (CLEAR PRESET)
CLR PRE+ number key: to clear the relative preset.
Long press to clear all preset.

FOCUS KEY ( ON THE LEFT)
Manual focus, only valid under manual focus model.

ZOOM KEY( ON THE RIGHT SIDE)
Set the zoom rate.

NAVIGATE KEY: UP/DOWN/LEFT/RIGHT
Under working mode, use navigate key to set the pan tilt, and select menu when enter OSD.

OK /HOME KEY
Under working mode, short press OK to make the camera go back to HOME position; and confirm the selection when enter OSD.

AF: Auto Focus.
MF: Manual Focus.
RESET: Press 3 seconds to reset camera. MENU: Enter OSD menu.

LEARN+LIMIT L key: Set the pan tilt left limit position.
LEARN+LIMIT R key: Set the pan tilt right limit position.
LEARN+LMT CLR key: Clear the limit position.

BLC OFF/ BLC ON: Not Available.
BRIGHT-/BRIGHT+: Set image brightness, only valid under bright priority exposure mode.

Video Format Keys:
Long press 3 seconds to select different video format output.

VISCA IN (RS232 PORT)

No. V_IN V_OUT VISCA IN RS485
1 DTR DTR 1
2 DSR DSR 2
3 TXD TXD 3
4 GND GND 4
5 RXD RXD 5
6 A 6 A(+)
7 IR OUT 7 IR OUT
8 B 8 B(-)

VISCA IN &Mini DIN Connection 

Camera VISCA IN Mini DIN
1 DTR
2 DSR
3 TXD
4 GND
5 RXD
6 A(+)
7 IR OUT
8 B(-)

VISCA IN & DB9 Connection 

Camera VISCA IN Windows DB- 9
1 DTR
2 DSR
3 TXD
4 GND
5 RXD
6 A(+)
7 IR OUT
8 B(-)

VISCA Network Construction:

SERIAL PORT CONFIGURATION

Parameter Value Parameter Value
Baud rate 2400/4800/9600/115200 Stop Bit 1bit
Start Bit 1 bit Check Bit None
Date Bit 8 bit

VISCA PROTOCOL

Part1 Camera Return Command

Ack/Completion Message

| Command Packet| Note
ACK| z0 41 FF| Returned when the command is accepted.
Completion| z0 51 FF| Returned when the command has been executed.

z = camera address+8

Error Messages

| Command Packet| Note
Syntax Error| z0 60 02 FF| Returned when the command format is different or when a command with illegal command parameters is accepted
Command Not Executable|

z0 61 41 FF

| Returned when a command cannot be executed due to current conditions. For example, when commands controlling the focus manually are received during auto focus.

Part 2 Camera Control Command

Command type| function| command|
---|---|---|---
Address Set| Broadcast| 88 30 01 FF| Address setting
IF_Clear| Broadcast| 88 01 00 01 FF| I/F Clear
Command Cancel| | 8x 21 FF|


CAM_Power

| On| 8x 01 04 00 02 FF| ****

Power ON/OFF

Off| 8x 01 04 00 03 FF
CAM_Zoom| Stop| 8x 01 04 07 00 FF|
Tele(Standard)| 8x 01 04 07 02 FF
Wide(Standard)| 8x 01 04 07 03 FF
Tele(Variable)| 8x 01 04 07 2p FF| ****

p = 0(low)~7(high)

Wide(Variable)| 8x 01 04 07 3p FF
Direct| 8x 01 04 47 0p 0q 0r 0s FF| pqrs: Zoom Position  (0(wide) ~0x4000(tele))
Direct with speed| 8x 0A 04 47 0t 0p 0q 0r 0s FF| t: spd  0~7
pqrs: Zoom Position  (0(wide) ~0x4000(tele))
CAM_DZoom| ON| 8x 01 04 06 02 FF|
OFF| 8x 01 04 06 03 FF
Combine Mode| 8x 01 04 36 00 FF| Combine with optical zoom control
Separate Mode| 8x 01 04 36 01 FF| Separate with optical zoom control
Stop| 8x 01 04 06 00 FF| Enable In separate mode
Tele (Variable)| 8x 01 04 06 2p FF| Enable In separate mode
Wide (Variable)| 8x 01 04 06 3p FF| Enable In separate mode
Direct| 8x 01 04 46 0p 0q 0r 0s FF| Enable In separate mode
| Stop| 8x 01 04 08 00 FF|
Command type| function| command|
CAM_Focus| Far(Standard)| 8x 01 04 08 02 FF|
| Near(Standard)| 8x 01 04 08 03 FF|
| Far (Variable)| 8x 01 04 08 2p FF| p=0 (Low) to 7 (High)
| Near (Variable)| 8x 01 04 08 3p FF| p=0 (Low) to 7 (High)
| Direct| 8x 01 04 48 0p 0q 0r 0s FF| pqrs: Focus Position
| Auto Focus| 8x 01 04 38 02 FF|
| Manual Focus| 8x 01 04 38 03 FF|
| One Push AF| 8x 01 04 18 01 FF|
CAM_Zoom Focus| Direct| 8x 01 04 47 0p 0q 0r 0s 0t 0u 0v 0w FF| pqrs: Zoom Position  (0(wide)~ 0x4000(tele))

tuvw: Focus Position

CAM_WB| Auto| 8x 01 04 35 00 FF|
| Indoor| 8x 01 04 35 01 FF|
| Outdoor| 8x 01 04 35 02 FF|
| One Push| 8x 01 04 35 03 FF|
| ATW| 8x 01 04 35 04 FF|
| Manual| 8x 01 04 35 05 FF|
| Sodium lamp| 8x 01 04 35 08 FF|
| fluorescent| 8x 01 04 35 09 FF|
| One Push Trigger| 8x 01 04 10 05 FF|
CAM_R Gain| Reset| 8x 01 04 03 00 FF| Manual Control of R Gain
| Up| 8x 01 04 03 02 FF|
| Down| 8x 01 04 03 03 FF|
| Direct| 8x 01 04 43 00 00 0p 0q FF| pq: R Gain  (0~0xFF)
CAM_B gain| Reset| 8x 01 04 04 00 FF| Manual Control of B Gain
| Up| 8x 01 04 04 02 FF|
| Down| 8x 01 04 04 03 FF|
| Direct| 8x 01 04 44 00 00 0p 0q FF| pq: B Gain  (0-0xFF)
CAM_AE| Full Auto| 8×01 04 39 00 FF| Automatic Exposure mode
| Manual| 8x 01 04 39 03 FF| Manual Control mode
| Shutter Priority| 8x 01 04 39 0A FF| Shutter Priority
Automatic Exposure mode
| Iris Priority| 8x 01 04 39 0B FF| Iris Priority Automatic Exposure mode
| Bright| 8x 01 04 39 0D FF| Bright Mode (Manual control)
CAM_Shutter| Reset| 8x 01 04 0A 00 FF| Shutter Setting
| Up| 8x 01 04 0A 02 FF|
Command type| function| command|
| Down| 8x 01 04 0A 03 FF|
| Direct| 8x 01 04 4A 00 00 0p 0q FF| pq: Shutter Position  (0~0x15)
CAM_Iris| Reset| 8x 01 04 0B 00 FF| Iris Setting(0~0xD)
| Up| 8x 01 04 0B 02 FF|
| Down| 8x 01 04 0B 03 FF|
| Direct| 8x 01 04 4B 00 00 0p 0q FF| pq: Iris Position (0~ 0x11)
CAM_Gain| Reset| 8x 01 04 0C 00 FF| Gain  Setting  (0~0x0F)
| Up| 8x 01 04 0C 02 FF|
| Down| 8x 01 04 0C 03 FF|
| Direct| 8x 01 04 0C 00 00 0p 0q FF| pq: Gain  Positon (0~0x0E)
CAM_Bright| Reset| 8x 01 04 0D 00 FF| Bright  Setting
| Up| 8x 01 04 0D 02 FF|
| Down| 8x 01 04 0D 03 FF|
| Direct| 8x 01 04 4D 00 00 0p 0q FF| pq: Bright l Positon  (0~0x1B)
CAM_WDR| On| 8x 01 04 3D 02 FF| Exposure Compensation ON/OFF
| Off| 8x 01 04 3D 03 FF|
| Direct| 8x 01 04 D3 pq FF| pq: ExpComp Position (0~0x6)
CAM_Back Light(BLC)| On| 8x 01 04 33 02 FF| BackLight On
| Off| 8x 01 04 33 03 FF| BackLight Off
CAM_Sharpness| Reset| 8x 01 04 02 00 FF| Aperture Control
| Up| 8x 01 04 02 02 FF|
| Down| 8x 01 04 02 03 FF|
| Direct| 8x 01 04 42 00 00 0p 0q FF| pq: Aperture Gain (0~0x0F)
CAM_Memory(preset)| Reset| 8x 01 04 3F 00 pp FF|

pp: Preset Number(=0 to 127) Corresponds to 0 to 9 on the Remote Commander

| Set| 8x 01 04 3F 01 pp FF|
| Recall| 8x 01 04 3F 02 pp FF|
CAM_LR_Reverse| On| 8x 01 04 61 02 FF|

Image Flip Horizontal ON/OFF

| Off| 8x 01 04 61 03 FF|
CAM_Picture Flip| On| 8x 01 04 66 02 FF|

Image Flip Vertical ON/OFF

| Off| 8x 01 04 66 03 FF|
CAM_RS485Ctl| On| 8x 01 06 A5 02 FF|
| Off| 8x 01 06 A5 03 FF|
CAM_Saturation| Saturation| 8x 01 04 A1 00 00 0p 0q FF| pq:saturation level 0x00~0x0f
CAM_Contrast| Contrast| 8x 01 04 A2 00 00 0p 0q FF| pq:Contrast level 0x00~0x0f
Command type| function| command|

CAM_Speed By Zoom

| On| 8x 01 06 A0 02 FF|
| Off| 8x 01 06 A0 03 FF|
CAM_PT Speed| PT Speed| 8x 01 04 C1 00 00 0p 0q FF| pq: PT speed  0x05~0x18
CAM_Zoom Speed| Zoom Speed| 8x 01 04 D1 00 00 0p 0q FF| pq: Zoom speed 0x01~0x07

CAM_Zoom Display

| On| 8x 01 06 C2 02 FF|
| Off| 8x 01 06 C2 03 FF|
CAM_Freeze| Freeze| 8x 01 04 75 0p FF| p: Freeze switch 3=OFF, 2=ON
CAM_Preset Freeze Set| Preset Freeze Set| 8x 01 04 76 0p FF| p: Preset Freeze switch 3=OFF, 2=ON
CAM_Preset Speed Set| Preset Speed Set| 8x 01 7E 01 0B pp qq FF| pp: Preset NO.
qq: Preset Speed 2~24 default:15
CAM_Preset Speed Adj| Preset Speed Adj| 8x 01 7E 01 1B 0p FF| p: Adjustment of direction
3=down, 2=up
CAM_IR address| IR address| 8x 01 06 D8 0p FF| p:IR address 1~4
CAM_Gamma| Gamma set| 8x 01 04 5B 0p FF| P:Gamma NO. (0~4)
CAM_2D
Noise Reduction| Direct| 8x 01 04 A5 0p FF| (0~0x01)
CAM_3D
Noise Reduction| Direct| 8x 01 04 53 0p FF| (0~0x05)
FLICK| 50HZ| 8x 01 04 23 01 FF|
| 60HZ| 8x 01 04 23 02 FF|
| OFF| 8x 01 04 23 00 FF|
Video System Set(Factory)| | 8x 01 06 35 00 pp FF| pp:  Video format 1080P60 0x00

1080P50          0x01

1080I60           0x02

1080I50           0x03

1080P30          0x04

1080P25          0x05

720P60            0x06

720P50            0x07

720P30            0x08

720P25            0x09

1080P5994      0x0E

1080I5994       0x0F

1080P2997      0x10

720P5994        0x13

720P2997        0x14

1080P24          0x11

1080P2398      0x12

Video System Set(Sony)| | 8x 01 04 24 72 0p 0q FF| pq:  Video format 1080P60 0x2e

1080P50          0x2f

1080I60           0x01

1080I50           0x04

1080P30          0x06

1080P25          0x08

720P60            0x09

720P50            0x0c

720P30            0x0e

720P25            0x11

1080P5994      0x13

1080I5994       0x02

1080P2997      0x07

720P5994        0x0a

Command type| function| command|
| | | 720P2997        0x0f

1080P24          0x2a

1080P2398      0x2b

CAM_ID Write| | 8x 01 04 22 0p 0q 0r 0s FF| pqrs: Camera ID (=0000 to FFFF)
DHCP control| DHCP off| 8x 01 04 AE 00 FF| DHCP off
| DHCP on| 8x 01 04 AE 01 FF| DHCP on
IP address control| IP set| 8x 01 04 AB 0p 0q 0r 0s 0m 0n 0x 0y FF| Set ip to :pq.rs.mn.xy
| Mask set| 8x 01 04 AC 0p 0q 0r 0s 0m 0n 0x 0y FF| Set mask to :pq.rs.mn.xy
| Gateway set| 8x 01 04 AD 0p 0q 0r 0s 0m 0n 0x 0y FF| Set gateway to : pq.rs.mn.xy
Mainstream| resolution|

8x 01 04 C2 00 0p 0q 0r 0s 0m 0n 0x 0y FF

| pqrs : Column(x size) mnxy: Line (y size) only support: 19201080  1280720 1024*576
| rate| 8x 01 04 C2 01 0p 0q 0r 0s 0m 0n 0x 0y FF| pqrsmnxy: bitrate (1024~16384kbps)
| Encode Mode| 8x 01 04 C2 02 0p 0q FF| Mode sel:0xpq 0x00:h264 0x01:h265
| Frame Rate| 8x 01 04 C2 03 0p 0q FF| Frame rate:0xpq (3~60)
| IDR| 8x 01 04 C2 04 0p 0q FF| IDR Setting:0xpq (3~120)
|

Stream Rate Mode

|

8x 01 04 C2 05 0p 0q FF

| Contor mode:0xpq 0x00:CBR

0x01:VBR

Sub stream|

resolution

| 8x 01 04 C3 00 0p 0q 0r 0s 0m 0n 0x 0y FF| pqrs : Column(x size) mnxy: Line (y size) only support: 640*360
| rate| 8x 01 04 C3 01 0p 0q 0r 0s 0m

0n 0x 0y FF

| pqrsmnxy: bitrate

(1024~2048kbps)

| Encode Mode| 8x 01 04 C3 02 0p 0q FF| Mode sel:0xpq 0x00:h264 0x01:h265
| Frame Rate| 8x 01 04 C3 03 0p 0q FF| Frame rate:0xpq (3~60)
| IDR| 8x 01 04 C3 04 0p 0q FF| IDR Setting:0xpq (3~120)
| Stream Rate Mode| 8x 01 04 C3 05 0p 0q FF| Contor mode:0xpq 0x00:CBR 0x01:VBR
Color adjust| Color adjust OFF| 8x 01 04 B6 00 FF| Color adjust off
| Color adjust ON| 8x 01 04 B6 01 FF| Color adjust on
| brightness balance

OFF

| 8x 01 04 B7 00 FF| Keep Brightness
| brightness balance

ON

| 8x 01 04 B7 01 FF| No keep Brightness
| Flare red| 8x 01 04 B8 dat FF| Flare mode red value

Default is 32

| Flare green| 8x 01 04 B9 dat FF| Flare mode green value

Default is 32

| Flare green| 8x 01 04 BA dat FF| Flare mode blue value

Default is 32

SYS_Menu| Menu On| 8x 01 06 06 02 FF| Turn on the menu
| Menu Off| 8x 01 06 06 03 FF| Turn off the menu
| Menu Back| 8x 01 06 06 10 FF| Menu step back
Command type| function| command|
| Menu OK| 8x 01 7E 01 02 00 01 FF| Menu ok
IR_Receive| On| 8x 01 06 08 02 FF| IR(remote commander)receive ON/OFF
| Off| 8x 01 06 08 03 FF|
| On/Off| 8x 01 06 08 10 FF|
Cam_Tally| RGB| x 01 7E 01 0A 00 0p FF| P=0:                 OFF

P=1:                 RED

P=2:                 GREEN

P=3:                 RED&GREEN

P=4:                 BLUE

P=5:                 RED&BLUE P=6:                        GREEN&BLUE

P=7:                 RED&GREEN&BLUE

Pan_tilt Drive| Up| 8x 01 06 01 VV WW 03 01 FF| VV: Pan speed 0x01 (low speed) to 0x18 (high speed)

WW: Tilt speed 0x01 (low speed) to 0x14 (high speed)

YYYY: Pan Position(TBD) ZZZZ: Tilt Position(TBD)

| Down| 8x 01 06 01 VV WW 03 02 FF|
| Left| 8x 01 06 01 VV WW 01 03 FF|
| Right| 8x 01 06 01 VV WW 02 03 FF|
| Up left| 8x 01 06 01 VV WW 01 01 FF|
| Up right| 8x 01 06 01 VV WW 02 01 FF|
| Down Left| 8x 01 06 01 VV WW 01 02 FF|
| Down Right| 8x 01 06 01 VV WW 02 02 FF|
| Stop| 8x 01 06 01 VV WW 03 03 FF|
| Absolute Position| 8x 01 06 02 VV WW

0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF

|
| Relative Position| 8x 01 06 03 VV WW

0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF

|
| Home| 8x 01 06 04 FF|
| Reset| 8x 01 06 05 FF|

Pan-tilt Limit Set

| Set| 8x 01 06 07 00 0W

0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF

| W:1 Up Right 0:Down Left YYYY: Pan Limit Position(TBD) ZZZZ: Tilt Limit Position(TBD)
| Clear| 8x 01 06 07 01 0W
07 0F 0F 0F 07 0F 0F 0F FF|

Part 3 Camera Lnquiry Command

Command type command return note
CAM_Power Inq 8x 09 04 00 FF y0 50 02 FF On
y0 50 03 FF Off(Standby)
CAM_Zoom Pos Inq 8x 09 04 47 FF y0 50 0p 0q 0r 0s FF pqrs: Zoom Position
CAM_DZoom On Off Inq 8x 09 04 06 FF y0 50 0p FF p 2: ON 3: OFF
CAM_DZoom Mode Inq 8x 09 04 36 FF y0 50 0p FF p 0:combination mode

1:separate mode
CAM_DZoom Posi Inq| 8x 09 04 46 FF| y0 50 0p 0q 0r 0s FF| pqrs: Zoom Position
CAM_Speed By Zoom Inq| 8x 09 06 A0 FF| y0 50 0p FF| p 2: ON 3: OFF
CAM_PT Speed Inq(IR)| 8x 09 04 C1 FF| y0 50 pp FF| pp: 0x05~0x18
CAM_Zoom Speed Inq(IR)| 8x 09 04 D1 FF| y0 50 0p FF| p:0x00~0x07
CAM_Focus Mode Inq| 8x 09 04 38 FF| y0 50 02 FF| Auto Focus
y0 50 03 FF| Manual Focus
pqrs: Focus Position
(0~0x01)

p: 0: off     1: on

(0~0x05)

p:0:off       1: auto 2~5: noise level

Auto
y0 50 01 FF| Indoor mode
y0 50 02 FF| Outdoor mode
y0 50 03 FF| OnePush mode
y0 50 04 FF| ATW
y0 50 05 FF| Manual
pq: R Gain
pq: B Gain
pq: saturation
pq: contrast
Full Auto
y0 50 03 FF| Manual
y0 50 0A FF| Shutter priority
y0 50 0B FF| Iris priority
y0 50 0D FF| Bright
p  0: OFF

1: 50HZ

2: 60HZ

pq: Shutter Position
pq: Iris Position
pq: Gain Position
pq: Bright Position
On
y0 50 03 FF| Off
p: WDR Position
pq: Aperture Gain
pp: Memory number q: 1=preset exist

0=preset not saved

On
y0 50 03 FF| Off
On
y0 50 03 FF| Off
On
y0 50 03 FF| Off
pqrs: Camera ID
mn pq rs tu vw FF|
pp: Video format
pp: Video format
On
y0 50 03 FF| Off
On
y0 50 03 FF| Off
ww: Pan Max Speed zz: Tilt Max Speed
wwww: Pan Position zzzz: Tilt Position
pqrs : Column(x size) mnxy: Line (y size) only support: 1920*1080

1280*720

1024*576

pqrsmnxy: bitrate (1024~16384kbps)
Mode sel:0xpp 0x00:h264

0x01: h265

Frame rate:0xpp

(3~60)

IDR Setting:0xpp

(3~120)

Contor mode:0xpp 0x00:CBR

0x01:VBR

pqrs : Column(x size) mnxy: Line (y size) only support:

640*360

pqrsmnxy: bitrate (1024~2048kbps)
Mode sel:0xpp 0x00:h264

0x01: h265

Frame rate:0xpp

(3~60)

IDR Setting:0xpp

(3~120)

Contor mode:0xpp 0x00:CBR

0x01:VBR

VISCA PAN TILT ABSOLUTE POSITION VALUE

Pan Angle VISCA Value Tilt Angle VISCA Value
-170 0xF670 -30 0xFE50
-135 0xF868 0 0x0000
-90 0xFAF0 30 0x01B0
-45 0xFD78 60 0x0360
0 0x0000 90 0x510
45 0x0288
90 0x0510
135 0x0798
170 0x0990

VISCA PAN TILT SPEED VALUE

Pan(Degree/Second) Pan(Degree/Second))
0 0.3
1 1
2 1.5
3 2.2
4 2.4
5 2.6
6 2.8
7 3.0
8 3.2
9 3.4
10 3.8
11 4.5
12 6
13 9
14 15
15 19
16 25
17 32
18 38
19 45
20 58
21 75
22 88
23 105
24 120

PELCO-D Protocol Command List

| Function| Byte1| Byte2| Byte3| Byte4| Byte5| Byte6| Byte7|
---|---|---|---|---|---|---|---|---|---
| Up| 0xFF| Address| 0x00| 0x08| Pan Speed| Tilt Speed| SUM|
| Down| 0xFF| Address| 0x00| 0x10| Pan Speed| Tilt Speed| SUM|
| Left| 0xFF| Address| 0x00| 0x04| Pan Speed| Tilt Speed| SUM|
| Right| 0xFF| Address| 0x00| 0x02| Pan Speed| Tilt Speed| SUM|
| Up left| 0xFF| Address| 0x00| 0x0C| Pan Speed| Tilt Speed| SUM|
| Up right| 0xFF| Address| 0x00| 0x0A| Pan Speed| Tilt Speed| SUM|
| Down Left| 0xFF| Address| 0x00| 0x14| Pan Speed| Tilt Speed| SUM|
| Down Right| 0xFF| Address| 0x00| 0x12| Pan Speed| Tilt Speed| SUM|
| Zoom In| 0xFF| Address| 0x00| 0x20| 0x00| 0x00| SUM|
| Zoom Out| 0xFF| Address| 0x00| 0x40| 0x00| 0x00| SUM|
| Focus Far| 0xFF| Address| 0x00| 0x80| 0x00| 0x00| SUM|
| Focus Near| 0xFF| Address| 0x01| 0x00| 0x00| 0x00| SUM|
| Set Preset| 0xFF| Address| 0x00| 0x03| 0x00| Preset ID| SUM|
| Stop| 0xFF| Address| 0x00| 0x00| Pan Speed| Tilt Speed| SUM|
| Clear Preset| 0Xff| Address| 0x00| 0x05| 0x00| Preset ID| SUM|
| Call Preset| 0Xff| Address| 0x00| 0x07| 0x00| Preset ID| SUM|
| Query Pan Position| 0Xff| Address| 0x00| 0x51| 0x00| 0x00| SUM|
| Query Pan Position

Response

| 0Xff| Address| 0x00| 0x59| Value High

Byte

| Value Low

Byte

| SUM|
| Query Tilt Position| 0Xff| Address| 0x00| 0x53| 0x00| 0x00| SUM|
| Query Tilt Position Response| 0Xff| Address| 0x00| 0x5B| Value High Byte| Value Low Byte| SUM|
| Query Zoom Position| 0Xff| Address| 0x00| 0x55| 0x00| 0x00| SUM|
| Query Zoom Position Response| 0Xff| Address| 0x00| 0x5D| Value High Byte| Value Low Byte| SUM|
Function| Byte1| Byte2| Byte3| Byte4| Byte5| Byte6| Byte7| Byte8
Up| 0Xa0| Address| 0x00| 0x08| Pan Speed| Tilt Speed| 0Xaf| XOR
Down| 0Xa0| Address| 0x00| 0x10| Pan Speed| Tilt Speed| 0Xaf| XOR
Left| 0Xa0| Address| 0x00| 0x04| Pan Speed| Tilt Speed| 0Xaf| XOR
Right| 0Xa0| Address| 0x00| 0x02| Pan Speed| Tilt Speed| 0Xaf| XOR
Up left| 0Xa0| Address| 0x00| 0x0C| Pan Speed| Tilt Speed| 0Xaf| XOR
Up right| 0Xa0| Address| 0x00| 0x0A| Pan Speed| Tilt Speed| 0Xaf| XOR
Down Left| 0Xa0| Address| 0x00| 0x14| Pan Speed| Tilt Speed| 0Xaf| XOR
Down Right| 0Xa0| Address| 0x00| 0x12| Pan Speed| Tilt Speed| 0Xaf| XOR
Zoom In| 0Xa0| Address| 0x00| 0x20| 0x00| 0x00| 0Xaf| XOR
Zoom Out| 0Xa0| Address| 0x00| 0x40| 0x00| 0x00| 0Xaf| XOR
Focus Far| 0Xa0| Address| 0x00| 0x80| 0x00| 0x00| 0Xaf| XOR
Focus Near| 0Xa0| Address| 0x01| 0x00| 0x00| 0x00| 0Xaf| XOR
Stop| 0Xa0| Address| 0x00| 0x00| Pan Speed| Tilt Speed| 0Xaf| XOR
Set Preset| 0xA0| Address| 0x00| 0x03| 0x00| Preset ID| 0xAF| XOR
Clear Preset| 0xA0| Address| 0x00| 0x05| 0x00| Preset ID| 0xAF| XOR
Call Preset| 0xA0| Address| 0x00| 0x07| 0x00| Preset ID| 0xAF| XOR
Query Pan Position| 0xA0| Address| 0x00| 0x51| 0x00| 0x00| 0xAF| XOR
Query Pan Position

Response

| ****

0xA0

| ****

Address

| ****

0x00

| ****

0x59

| Value High Byte| Value Low Byte| ****

0xAF

| ****

XOR

Query Tilt

Position

| 0xA0| Address| 0x00| 0x53| 0x00| 0x00| 0xAF| XOR
Query Tilt

Position Response

| ****

0xA0

| ****

Address

| ****

0x00

| ****

0x5B

| Value High Byte| Value Low Byte| ****

0xAF

| ****

XOR

Query Zoom Position| 0xA0| Address| 0x00| 0x55| 0x00| 0x00| 0xAF| XOR
Query Zoom

Position Response

| ****

0xA0

| ****

Address

| ****

0x00

| ****

0x5D

| Value High Byte| Value Low Byte| ****

0xAF

| ****

XOR

| | | | | | | | | | | | | | | | |

OSD MENU

  1. Under working mode, press the MENU key on the IR remote controller, to enter the OSD menu as bellow:

  2. After enter the main menu, use the navigate UP/DOWN key to select the main menu. Once been selected, the main menu will change to blue background, and the right side will show all sub menu options.

  3. Press the navigate RIGHT key to enter sub menu; use UP/DONW key to select the sub menu; use LEFT/RIGHT key to select parameter.

  4. Press the MENU key again to return to previous menu. Press the MENU key continuously to exit the OSD menu.

  5. OSD Menu Setting List

SYSTEM

| PROTOCOL| Optional item:VISCA、PLC.P、PLC.D| Default:VISCA
---|---|---|---
ADDRESS| VISCA:1~7                 PLC.P/PLC.D:1~255| Default:1
BAUD RATE| Optional item:2400、4800、9600、115200| Default:9600
PTL LOCK| Protocol lock: once set, above protocol setting will be locked| Default:OFF
RS485| RS485 ON/OFF| Default:ON
VISCA| Optional Item: OVER ALL、OVER IP、OVER COM| Default:OVER ALL
LANGUAGE| Optional Item: Chinese、English| Default:English

EXPOSURE

| EXPOSURE

MODE

|

AUTO、MANUAL、SHUTTER、IRIS、BRIGHT

|

Default:AUTO

---|---|---|---

SHUTTER

| Shutter speed: 1/30~1/10000, only valid under MANUAL and

SHUTTER mode

|

Default:AUTO

IRIS

| Iris setting: CLOSE~F1.8, only valid under MANUAL and IRIS

mode

|

Default:AUTO

GAIN| Gain setting: 0dB~30dB , only valid under MANUAL mode| Default:AUTO
EBRIGHT| Bright setting: 0~27, only valid under BRIGHT priority mode.| Default:AUTO
BRIGHT| 0~15| Default:8
WD MODE| ON/OFF| Default:OFF
WD LEVEL| WDR Level| Default:1
BLC| ON/OFF| Default:OFF

IMAGE

|

WB MODE

| Optional:ATW、MANUAL、AUTO、INDOOR、OUTDOOR、 PUSH|

Default:ATW

---|---|---|---
R GAIN| Red gain level: 0~255, only valid under manual white balance mode| Default:AUTO
B GAIN| Blue gain level:0~255 , only valid under manual white balance mode| Default:AUTO
FLICK| Anti-Flicker setting:50/60HZ, to reduce the video flicker| Default:50HZ
DZOOM| ON/OFF| Default:OFF
FOCUS| Select focus mode| Default:AUTO

QUALITY

|

2D NR

| 2D noise reduction: the bigger value is, the less noise on image

is, the lower resolution is.

|

Default:OFF

---|---|---|---

3D NR

| 3D noise reduction: OFF/AUTO/0~4, the bigger value is, the less motion noise on image is. High value will cause image

smear.

|

Default:AUTO

SHARPNESS

| Sharpness setting: 0~15, the higher value is, edge of the image

will be sharpen

|

Default:3

CONTRAST| Set contrast level| Default:8
SATURATION| Set saturation.| Default:8
GAMMA| Select gamma level| Default:0

AF SENSITIVITY

|

Optional:LOW/NORMAL/HIGH

| Default:

NORMAL

PTZ

|

SPEEDBYZ

| Speed By Zoom: proportional speed, the bigger the zoom is, the

slower the speed is

|

Default:ON

---|---|---|---
FLIP.HOR| Flip horizontal| Default:OFF
FLIP VER| Flip vertical| Default:OFF
PT SPD| Pan Tilt speed| Default:18
ZOOM SPD| Zoom speed| Default:5
MENU MIR| Optional Item: NORMAL、MIRROR| Default:NORMAL
PRE FRZ| Open/Close Video Freeze when running presets| Default:OFF
PRE PTSPD| Preset head speed: 2~24| Default:15
PRE ZSPD| Preset zoom speed: 1~7| Default:5

FORMAT

| 1080P59.94| 1080P50|

After selecting the system, press OK to switch the system. If it is the currently selected system, it will not be activated

---|---|---|---
1080I59.94| 1080I50
1080P29.97| 1080P25
720P59.94| 720P50
720P29.97| 720P25
1080P60| 1080P30
720P60| 720P30
1080I60| 1080P24

IP

| DHCP| ON/OFF|

Using up/down/left/right navigation button to select item to set, and using number button to set parameter.

Press menu button to return.

---|---|---|---
IP| 192.168.001.188
MASK| 255.255.255.000
GW (Gateway)| 192.168.001.001
MAIN| Default:19201080
BITRATE| Default:04096k
SUB| Default:1280
720
BITRATE| Default:02048k

RESET

| SYS RESET| Reset communication parameter to default
---|---|---
CAM RESET| Reset camera parameter to default
PT RESET| Reset pan/tilt parameter to default
ALL RESET| Reset all parameter to default

INFO

| IR ADDR| Camera IR control address
---|---|---
USB| USB firmware version
CLIENT| Default client end protocol: VISCA
MODEL NO.| Model number
ARM VER| ARM firmware version
FPGA VER| FPGA firmware version
CAM VER| Camera version
RELEASE| Software release date

Set IP Address in Menu
In order to facilitate customer debugging, the camera has the support menu to set IP address. The specific methods are as follows:

  1. Press “MENU” to open the menu interface, select “network parameters” in the menu to call up the IP setting interface:

  2. Right click the remote control to enter the IP setting interface, and select the parameters to be set by using the navigation up and down keys, and then select the IP address, mask, gateway:

  3. Short press the number key to set the corresponding parameters. After setting the current parameters, press the “MENU” key again to complete the current parameter setting;

  4. To exit the menu, just press the “MENU” key again.

UVC CONTROL

  1.  Only run the client software after the USB3.0 camera has completed self-configuration (the IR indicator in blue color and will not flash); otherwise may cause black video issue.
  2. Make sure the USB3.0 camera is recognized by the PC Device Manager.
  3. Make sure the interval of video format switching more than 3 seconds, otherwise black video maybe caused.
  4. Make sure the interval of control command sending from the server (via USB) to the camera no less than 250ms.
  5. Support standard UVC interface.
    PU_BRIGHTNESS_CONTROL| 81 01 04 4d 00 00 0p 0q FF
    ---|---
    PU_CONTRAST_CONTROL| 81 01 04 A2 00 00 0p 0q FF
    PU_SATURATION_CONTROL| 81 01 04 A1 00 00 0p 0q FF
    PU_SHARPNESS_CONTROL| 8x 01 04 42 00 00 0p 0q FF
    PU_GAMMA_CONTROL| 8x 01 04 5B 0p FF
    PU_WHITE_BALANCE_TEMPERATURE_CONTROL| 8x 01 04 35 0X FF
    PU_BACKLIGHT_COMPENSATION_CONTROL| 81 01 04 33 02/03 FF
    PU_POWER_LINE_FREQUENCY_CONTROL| 8x 01 04 AA 00/01/02 FF
    CT_ZOOM_ABSOLUTE_CONTROL| 8x 01 04 47 0p 0q 0r 0s FF
    CT_PANTILT_ABSOLUTE_CONTROL| 8x 01 06 02 VV WW 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z F
    CT_PANTILT_RELATIVE_CONTROL| 8x 01 06 01 pp qq rr ss FF
    CT_ZOOM_RELATIVE_CONTROL| 8x 01 04 07 pp FF

WEB SETTING

It is not necessary to install additional video player plug-in to preview the local screen on the web interface.
The web interface supports Google Chrome, Firefox, IE, Safari, Opera, 360, QQ and other browsers, adaptability is very good.

Login
Run browser, input IP address (defaulted IP address is 192.168.1.188), to enter login interface, can select Language (Chinese or English), input admin and password to login as following: (Default Username: admin

Real-time Preview:

telycam-TLC-300-IP-12NDI-FHD-PTZ-Video-Camera- \(19\)

The preview interface is shown above. On the right side.with options to control camera pan, tilt, zoom, focus, focus mode, pan ti lt speed, focus speed, zoom speed, preset position control, etc. At the bottom of the image, you can select the volume switch and vol ume level, as well as the full-size view and picture-in-picture mode.

Parameter Setting
Click “Setting” to enter into parameter setting interface as following:

telycam-TLC-300-IP-12NDI-FHD-PTZ-Video-Camera- \(19\)

“Video Encode”: can set image encode mode, main stream and sub stream resolution/bit rate/frame rate, bit rate control way, and I frame interval etc as above image.

“video Transmission”: RTMP and NDI settings are available, as shown in the following figure:

“Audio Settings” : the audio enable can be off / on, the encoding mode can be selected, and the parameters such as sampling rate and bit rate can be adjusted, as shown in the following figure:

telycam-TLC-300-IP-12NDI-FHD-PTZ-Video-Camera- \(23\)

“Image Parameter”can set focus, exposure, white balance, image, image quality, noise-reduction, as following picture.

Focus including focus mode, default focal distance, digital zoom etc

telycam-TLC-300-IP-12NDI-FHD-PTZ-Video-Camera- \(25\)

Exposure includes exposure mode, shutter speed, gain, iris, brightness, and anti-flicker.

telycam-TLC-300-IP-12NDI-FHD-PTZ-Video-Camera- \(26\)

White Balance includes white balance mode, red gain, blue gain.

telycam-TLC-300-IP-12NDI-FHD-PTZ-Video-Camera- \(26\)

Image includes mirror, flip, backlight compensation, Gamma, WDR(wide dynamic range).

telycam-TLC-300-IP-12NDI-FHD-PTZ-Video-Camera- \(28\)

Image Quality includes brightness, sharpness, contrast, saturation.

telycam-TLC-300-IP-12NDI-FHD-PTZ-Video-Camera- \(29\)

Noise reduction includes 2D/3D reduction. There is on/off option for 2D, and off/auto/1~4 six options.

telycam-TLC-300-IP-12NDI-FHD-PTZ-Video-Camera- \(30\)

“Ethernet” includes DHCP mode, IP address, Net mask, Gateway, HTTP Port, RTSP Port, Visca Over IP. Default parameter as following:

DHCP OFF Gateway 192.168.1.1 RTSP Port 554
IP address 192.168.1.188 DNS 192.168.1.1 RTSP Encrypt ON
Netmask 255.255.255.0 HTTP Port 80 Visca Over IP 52381

“Firmware upgrade”: it is for camera program upgrade, currently only for ISP part update. How to update:
As following picture, click “clicking to upload file” icon, open dialog box, select to open the file, and click “upgrade” to start. DO NOT power off or do other operation when upgrading, reboot the camera after 5 min when upgrade finished.
Then login web end to select “reset all” to reset the camera completely.

telycam-TLC-300-IP-12NDI-FHD-PTZ-Video-Camera- \(31\)

Reset to default: reset the camera to default setting

  • Reset simply: reset camera image parameter
  • Reset Completelyall: reset camera Ethernet and image parameter, language and protocol will not be reset.
  • Reboot: Reboot ISP part of camera

Account Setting: is used for setting camera account and password
Input the account firstly, then input same password twice, click set to finish Please remember account and password, otherwise you may be not able to login.

telycam-TLC-300-IP-12NDI-FHD-PTZ-Video-Camera- \(34\)

System Time: Set the time zone and NTP enable.

telycam-TLC-300-IP-12NDI-FHD-PTZ-Video-Camera- \(34\)

VIEW RTSP VIDEO VIA VLC

Default RTSP main streaming address: rtsp://192.168.1.188/stream/main
Default RTSP sub streaming address: rtsp://192.168.1.188/stream/sub
Default RTMP main streaming address: rtmp://192.168.1.188:1935/app/rtmpstream0 Default RTMP sub streaming address: rtmp://192.168.1.188:1935/app/rtmpstream1

  1. Run VLC Media Player.
  2. Media->network stream, to enter into “open media” interface.
  3. Input RTSP address in URL as following:
  4. Click play to view the real time image.
    Note: If there is much image lag, select “more option” to enter into following setting, change buffer time smaller (VLC default buffer time is 1000ms).

telycam-TLC-300-IP-12NDI-FHD-PTZ-Video-Camera- \(37\)

NewTek Tools Guide

Image Preview

  • Download the NewTek NDI Tools via https://ndi.tv/tools/ and install it.

  • Find out the NDI 4.5 Tools/Studio Monitor via Windows toolbars, and then open it, as bellow:telycam-TLC-300-IP-12NDI-FHD-PTZ-Video-Camera- \(38\)

  • Right click on the Studio Monitor screen, select the preview device:

  • Pan Tilt Control
    Refer to above picture, once open the video via Studio Monitor, it will show up the control panel on the right side, to control camera pan, tilt, zoom, focus, preset, focus.

  • Run WEB via Studio Monitor

Refer to above picture, once open the video via Studio Monitor, there will show up a setting icon at the lower right corner, single click this iron to enter WEB UI.

  • 4. How to use NDI tools to Virtual Input CAMERA

    • find out the NDI 4.5 Tools/Virtual Input via Windows toolbars, open it, then it will show up the NDI Virtual Input icon at the Windows toolbars, as bellow picture shows:

    • Right click on the NDI Virtual Input icon, to select the virtual device name:
      telycam-TLC-300-IP-12NDI-FHD-PTZ-Video-Camera- \(44\)

    • Take Zoom for example, select NewTek NDI Video as video camera, as bellow picture shows:
      This also work for other applications, such as GotoMeeting,Skype for Business, Hangouts.

VISCA OVER IP

VISCA over IP means VISCA protocol transmit via IP, to reduce RS232/RS485 cable layout (the controller must support IP communication function)
Communication port spec:

  • Control port: RJ45 Gigabit LAN
  • IP protocol: IPv4
  • Transmit protocol: UDP
  • IP address: set via web end or OSD menu
  • Port address: 523 81
  • Confirm send/transmission control: depend on applied program
  • Applied range: in the same segment, not suitable for bridge network
  • Turn on camera: In the menu, set VISCA option to OVER IP

How to use VISCA over IP
VISCA Command
It means commands from controller to peripheral equipment, when peripheral equipment receives commands, then return ACK. When commands executed, will return complete message. For different commands, camera will return different message.

VISCA Inquiry
It means inquiry from controller to peripheral equipment when peripheral equipment receives this kind of commands, it will return required message.

VISCA Reply
It means ACK, complete message, reply or error reply, it is sent from peripheral equipment to controller.
Command for mat: the following is message head and valid message format.

Note: LAN output way is big endian, LSB is in the front.

Payload type:
Data definition as following:

Name Value (Byte 0) Value (Byte 0) Value (Byte 0)
VISCA command 0x01 0x00 Stores the VISCA command.
VISCA inquiry 0x01 0x10 Stores the VISCA inquiry.
VISCA reply 0x01 0x11 Stores the reply for the VISCA command and VISCA

inquiry, or VISCA device setting command.
VISCA device setting command| 0x01| 0x20| Stores the VISCA device setting command.
Control command| 0x02| 0x00| Stores the control command.
Control reply| 0x02| 0x01| Stores the reply for the control command.

Payload length
Valid data length in Payload (1~16), is command length.
For example, when valid data length is 16

byte
Byte 2 : 0x00
Byte 3 : 0x10
Controller will save sequence number of each command, when one command sent, the sequence number of the command will add 1, when the sequence number becomes the max value, it will change to 0 for next time. The peripheral equipment will save sequence  number of each command, and return the sequence number to the controller.

Payload
According to Payload type, the following data will be saved.

  • VISCA command
    Save VISCA command packet

  • VISCA inquiry
    Save VISCA message packet

  • VI SCA reply
    Save VISCA return packet

  • VISCA device setting command
    Save VISCA equipment setting command packet.

  •  Control command
    The following data is saved in control command payload

Name Value Description
RESET 0x01 Resets the sequence number to 0.

The value that was set as the sequence number is ignored.

ERROR| 0x0Fyy| yy=01:Abnormality in the sequence number.
yy=02:Abnormality in the message(message type).

Controlled reply
The following data is saved in return command payload of control command.

Message Value Description
ACK 0x01 Reply for RESET.

Delivery confirmation
VISCA over IP uses UDP as transmission communication protocol, UDP communication message transmission is not stable, it is necessary to confirm delivery and resent in application.
Generally, when controller sends a command to peripheral equipment, controller will wait for the return message then send the next command, we can detect and confirm if the peripheral equipment receive the commands from return message’s lag time. If controller shows it is overtime, it is regarded as error transmission.
If controller shows it is overtime, resend the commands to check peripheral’s status, resent command sequence number is same as last command, the following chart list the received message and status after resending the commands.

Lost message| Recelved message for retransmission| Status after retransmission| Correspondence after retransmission
---|---|---|---
Command| ACK message| Command is performed by retransmission.| Continue processing.
Completion message For the command| ERROR(Abnormality in the sequence number.)| Command has been performed.

If only the ACK message is lost, the completion message returns.

| If the result by the completion message is needed, retransmit by updating the sequence number.
Completion message for the command| ERROR(Abnormality in the sequence number.)| Command has been performed.| If the result by the completion message is needed, retransmit by updating the sequence number.
Inquiry| Reply message| Inquiry is performed by retransmission.| Continue processing.
Reply message for the inquiry| ERROR(Abnormality in the sequence number.)| Inquiry has been performed.| If the result by the reply message is needed, retransmit by updating the sequence number.
Error message| Error message| Command is not performed. If the error cause eliminates, normal reply is return(ACK, reply message)| Eliminate the error cause. If normal reply returns, continue processing.
Inquiry of the VISCA device setting command| Reply message of the VISCA device setting command| Inquiry has been performed by retransmission.| Continue processing.
Reply message of the VISCA device setting command| ERROR(Abnormality in the sequence number.)| Inquiry has been performed.| If the result by the reply message is needed, retransmit by updating the sequence number.

Sequence chart as following

telycam-TLC-300-IP-12NDI-FHD-PTZ-Video-Camera- \(48\)

Sequence chart when command lost

telycam-TLC-300-IP-12NDI-FHD-PTZ-Video-Camera- \(49\)

Sequence chart when returned message lost

Note: Do not set IP address, sub net mask, gateway parameter in VISCA over IP command, otherwise, it will cause network breaks off. Due to change these parameter, network will be in off status.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals