telycam TLC-300-U2-12 USB2.0 HD Video Camera User Manual

USB2.0 HD Video Camera
User Manual Version V1.1
J.BC.0205.0041

SAFETY GUIDES

1. Before operation, please fully read and follow all instructions in the manual. For your safety, always keep this manual with the camera.
2. The camera power input range is 100-240VAC(50-60Hz),ensure the power supply input within this rate before powering on.
3. The camera power voltage is 12VDC, rated currency is 1.5A. We suggest you use it with the original power supply adapter supplied by the factory.
4. Please keep the power cable, video cable and control cable in a safe place. Protect all cables especially the connectors.
5. Operational environment: 0℃-50℃, humidity less than 90%.To avoid any danger, do not put anything inside the camera, and keep away from the corrosive liquid.
6. Avoid stress, vibration and damp during transportation, storage and installation.
7. Do not detetch the camera housing and cover. For any service, please contact authorized technicians.
8. RF cable and control cable should be individually shielded, and cannot be substituted with other cables. Do not direct the camera lens towards strong light, such as the sun or the intensive light.
9. Use a dry and soft cloth to clean the camera housing. Applied with neutral cleaning agent when there is need to clean. To avoid damage on the camera lens, never use strong or abrasive cleaning agents on the camera housing.
10. Do not move the camera by holding the camera head. To avoid mechanical trouble, do not rotate the camera head by hand.
11. Put the camera on fixed and smooth desk or platform, avoid leaned installation.
12. Power Supply Polarity(Drawing)

ACCESSORIES

Check all bellow items when open the package:
Camera ······································································· 1
Power Adapter ······························································ 1
Power Cable ································································· 1
RS232 Control Cable ······················································· 1
USB2.0 Cable ······························································· 1
Remote Controller ·························································· 1
User Manual ································································· 1
Double-sided Adhesive ···················································· 1

QUICK START

1. Check all cable connections before power on.
2. DIP Switch Setting (at the bottom of the camera):

Function（ARM）

| SW-1| SW-2| Instruction
1| OFF| OFF| Updating mode
2| ON| OFF| Debugging mode
3| OFF| ON| Undefined
4| ON| ON| Working mode

Function （IR CODE TYPE）

| SW-3| SW-4| Instruction
1| OFF| OFF| Off(Close IR receiver)
2| ON| OFF| Undefined
3| OFF| ON| SEJIN 4PPM CODE
4| ON| ON| NEC CODE(standard)

Function （USB）

| SW-5| SW-6| Instruction
1| OFF| OFF| Undefined
2| ON| OFF| Working mode
3| OFF| ON| Updating mode
4| ON| ON| Undefined

PRODUCT HIGHLIGHTS

• Smart and fashion design, ideal for cloud-based conferencing
• Adopts advanced DSP，1/2.8 inch 5MP image sensor, and high quality 12X 72.5degree FOV optical lens, provides fluent and crystal image quality
• Fast switching between different video formats: less than 1 second
• 12X Optical Zoom + 12XDigital Zoom
• Fast and accurate focus performance
• Easy firmware upgrade-(field-upgradable)
• USB2.0 high speed output
• Effective RS232/485 serial control
• Up to 128 presets
• Compatible with the majority of videoconferencing software (UVC1.5 protocol standard)
• With powerful functional remote controller
• IR transfer/IR pass function: except receiving the camera remote controller signal, the camera can also receive other codec’s IR remote control signal, and pass these IR control signal to the codec’s IR receiver (via VISCA IN port).

PRODUCT SPEC

installation
Pan/tilt Speed| Pan: 0.1°-120°/s; Tilt: 0.1° -80°/s
Preset| 10 via IR remote setting, 128 via VISCA control, preset accuracy: 0.1°
Control Port| RS232, RS485, USB2.0
Min. Lux| 0.01lux
White Balance| Auto/Manual
Focus| Auto/Manual
Iris| Auto/Manual
Shutter| Auto/Manual
WDR| Supported
BLC| Supported
2D Noise Reduction| Supported
3D Noise Reduction| Supported
Input Voltage| DC12V
Dimension| 148mm×132mm×161mm
Net weight| 1.25KG（2.8LBS）

CAMERA INTERFACE

1.Camera Lens
2.Camera Base
3.IR Receiver Panel
4.Indicator Light
5.Dial Switch| 6. Tripod Screw Hole
7.Installation Hole
8.RS232(VISCA IN) Port
9.USB2.0 Port
10.DC12V Power Input
11.Power Indicator light(red)
---|---

CAMERA DIMENSION(MM)

IR REMOTE CONTROLLER

LED Function Instruction
Press any button and shows in red color: Current selection is to control the camera;
Press any button and shows in green color: Current selection is to control the codec;
Press any button and shows in blue color: Current selection is to control the TV;
Power button
Red button: in normal work mode, short press one time, camera will enter standby mode; short press again, the camera will start self-configuration and go to HOME position; it will go to No.0 preset position if that was set;
Green button: Codec power button(need to learn the button coding);
Blue button: TV power button( need to learn the button coding);

Focus (Left): +/-
Manual focus, only valid under manual focus model;
Zoom (Right): +/-
Control the lens zoom rate; Navigate : Up/Down/Left/Right
In normal working mode, use navigate key to control pan/tilt;
Confirm/Home button:
In normal working mode, short press to let the camera go back to Home position.
Menu button: show the camera version Number buttons
Set Preset: Long press(3seconds) the number button to save preset;
Clear Preset: Clear+number button to clear the relative preset; Long press(3seconds) the Clear button to clear all preset;
Run Preset: Short press the number button to run the relative preset.
LEARNING FUNCTION：

1. Press the green button, the LED indicator light will show in green color for 1 second, means switch to video terminal/codec control mode;

2. Single Button Coding: long press(3seconds) Home +number”1″ button simultaneously, the green indicator LED will light, enter button learning mode, press the buttons which need to be learned, LED will start flickering(1HZ), now can start button learning: get the codec remote point to the camera remote’s infrared tube( about 10cm distance), then press the button which need to be learned, the LED re-flickering when learning finishes ; press other buttons which also need to be learned; Press the Home+”0″ buttons simultaneously to exit and save all remote data.
   If the button learning fails, the camera will enter normal working mode after 15seconds, LED will extinguish.

3. All Button Coding: long press (3seconds) Home+number”2″ button simultaneously, the green indicator LED will start flickering(1HZ), to enter all button learning mode: get codec remote point to the camera remote’s infrared tube( about 10cm distance), to start all button coding mode, the LED will extinguish when learning finished. If the button learning fails, the camera will enter normal working mode after 15seconds, LED will extinguish.

4. All Button Sending Mode: long press (3seconds) the Menu+ number “3” button simultaneously, the remote will enter all button sending mode.

5. Similar operation for the TV control mode learning.

VISCA IN (RS232) PORT

No.|

Function

---|---
1| DTR
2| DSR
3| TXD
4| GND
5| RXD
6| A
7| IR OUT
8| B

VISCA IN &RS485 Connection

Camera VISCA IN

|

RS485

---|---
1| DTR|
2| DSR|
3| TXD|
4| GND| GND
5| RXD|
6| A(+)| A(+)
7| IR OUT|
8| B(-)| B(-)

VISCA IN &DB9 Connection

Camera VISCA IN

|

Windows DB-9

---|---
1| DTR| 6| DSR
2| DSR| 4| DTR
3| TXD| 2| RXD
4| GND| 5| GND
5| RXD| 3| TXD
6| A(+)| |
7| IR OUT| |
8| B(-)| |

SERIAL PORT CONFIGURATION:

VISCA PROTOCOL

Part1 Camera Return Command

Ack/Completion Message

|

Command Packet

|

Note

ACK| z0 41 FF| Returned when the command is accepted.
Completion| z0 51 FF| Returned when the command has been executed.

Part2 Camera Control Command

Error Messages

|

Command Packet

|

Note

Syntax Error| z0 60 02 FF| Returned when the command format is different or when a command with illegal command parameters is accepted
Command Not  Executable|

z0 61 41 FF

| Returned when a command cannot be executed due to current conditions. For example, when commands controlling the focus manually are received during auto focus.

Part2 Camera Control Command

Command

| Funnation| Command Packet|

Note

---|---|---|---
AddressSet| Broadcast| 88 30 01 FF| Address setting
IF_Clear| Broadcast| 88 01 00 01 FF| I/F Clear
CAM_Power| On| 8x 01 04 00 02 FF| Power ON/OFF
Off| 8x 01 04 00 03 FF
CAM_Zoom| Stop| 8x 01 04 07 00 FF|
Tele(Standard)| 8x 01 04 07 02 FF
Wide(Standard)| 8x 01 04 07 03 FF
Tele(Variable)| 8x 01 04 07 2p FF| p = 0(low)~7(high)
Wide(Variable)| 8x 01 04 07 3p FF
Direct| 8x 01 04 47 0p 0q 0r 0s FF| pqrs: Zoom Position (0(wide)~0x4000(tele))
CAM_Focus| Stop| 8x 01 04 08 00 FF|
Far(Standard)| 8x 01 04 08 02 FF
Near(Standard)| 8x 01 04 08 03 FF
Direct| 8x 01 04 48 0p 0q 0r 0s FF| pqrs: Focus Position
One Push AF| 8x 01 04 18 01 FF|
CAM_ZoomFocus| Direct| 8x 01 04 47 0p 0q 0r 0s 0t 0u 0v 0w FF| pqrs: Zoom Position    (0(wide)~ 0x4000(tele)) tuvw: Focus Position
CAM_WB| Auto| 8x 01 04 35 00 FF|
Indoor| 8x 01 04 35 01 FF|
Outdoor| 8x 01 04 35 02 FF|
OnePush| 8x 01 04 35 03 FF|
| Manual| 8x 01 04 35 05 FF|
---|---|---|---
Outdoor Auto| 8x 01 04 35 06 FF|
Sodium Lamp Auto| 8x 01 04 35 07 FF|
Sodium Auto| 8x 01 04 35 08 FF|
CAM_RGain| Reset| 8x 01 04 03 00 FF| Manual Control of R Gain
Up| 8x 01 04 03 02 FF
Down| 8x 01 04 03 03 FF
Direct| 8x 01 04 43 00 00 0p 0q FF| pq: R Gain     (0~0xFF)
CAM_Bgain| Reset| 8x 01 04 04 00 FF| Manual Control of B Gain
Up| 8x 01 04 04 02 FF
Down| 8x 01 04 04 03 FF
Direct| 8x 01 04 44 00 00 0p 0q FF| pq: B Gain     (0-0xFF)
CAM_AE| Full Auto| 8x 01 04 39 00 FF| Automatic Exposure mode
Manual| 8x 01 04 39 03 FF| Manual Control mode
Bright| 8x 01 04 39 0D FF| Bright mode(Manual control)
CAM_Shutter| Reset| 8x 01 04 0A 00 FF| Shutter Setting
Up| 8x 01 04 0A 02 FF
Down| 8x 01 04 0A 03 FF
Direct| 8x 01 04 4A 00 00 0p 0q FF| pq: Shutter Position     (0~0x15)
CAM_Iris| Reset| 8x 01 04 0B 00 FF| Iris Setting
Up| 8x 01 04 0B 02 FF
Down| 8x 01 04 0B 03 FF
Direct| 8x 01 04 4B 00 00 0p 0q FF| pq: Iris Position      (0~ 0x11)
CAM_Gain| Reset| 8x 01 04 0C 00 FF| Gain Setting
Up| 8x 01 04 0C 02 FF
Down| 8x 01 04 0C 03 FF
Direct| 8x 01 04 0C 00 00 0p 0q FF| pq: Gain Positon   (0~0x0E)
CAM_Bright| Reset| 8x 01 04 0D 00 FF| Bright Setting
Up| 8x 01 04 0D 02 FF
Down| 8x 01 04 0D 03 FF
Direct| 8x 01 04 4D 00 00 0p 0q FF| pq: Bright l Positon     ()
CAM_WDR| On| 8x 01 04 3D 02 FF| WDR ON/OFF
Off| 8x 01 04 3D 03 FF
Direct| 8x 01 04 D3 0p FF| pq: WDR Position (1~0x06)
CAM_BackLight| On| 8x 01 04 33 02 FF| BackLight On
---|---|---|---
Off| 8x 01 04 33 03 FF| BackLight Off
CAM_Aperture| Reset| 8x 01 04 02 00 FF| Aperture Control
Up| 8x 01 04 02 02 FF
Down| 8x 01 04 02 03 FF
Direct| 8x 01 04 42 00 00 0p 0q FF| pq: Aperture Gain   (0~0x04)
CAM_Memory| Reset| 8x 01 04 3F 00 0p FF| p: Memory Number(=0 to 127) Corresponds to 0 to 9 on the Remote Commander
Set| 8x 01 04 3F 01 0p FF
Recall| 8x 01 04 3F 02 0p FF
CAM_LR_Reverse| On| 8x 01 04 61 02 FF| Image Flip Horizontal ON/OFF
Off| 8x 01 04 61 03 FF
CAM_PictureFlip| On| 8x 01 04 66 02 FF| Image Flip Vertical ON/OFF
Off| 8x 01 04 66 03 FF
CAM_ColorGain| Direct| 8x 01 04 49 00 00 00 0p FF| (0~0x0E)
CAM_2D Noise Reduction| Direct| 8x 01 04 53 0p FF| 0：OFF
1：ON
CAM_3D Noise Reduction| Direct| 8x 01 04 54 0p FF| 0:OFF   1：AUTO
2~5：LEVEL
FLICK| 50HZ| 81 01 04 23 01 FF|
60HZ| 81 01 04 23 02 FF|
Freeze| Freeze On| 81 01 04 62 02 FF| Freeze On Immediately
Freeze Off| 81 01 04 62 03 FF| Freeze Off Immediately
Preset Freeze On| 81 01 04 62 22 FF| Freeze On When Running Preset
Preset Freeze Off| 81 01 04 62 23 FF| Freeze Off When Running Preset

IR_Transfer

| Transfer On| 8x 01 06 1A 02 FF| Receive IR(remote commander) CODE from VISCA communication ON/OFF
Transfer Off| 8x 01 06 1A 03 FF
Pan_tiltDrive| Up| 8x 01 06 01 VV WW 03 01FF| VV: Pan speed 0x01 (low speed) to 0x18 (high speed)

WW: Tilt speed 0x01 (low speed) to 0x14 (high speed)

YYYY: Pan Position(TBD) ZZZZ: Tilt Position(TBD)

Down| 8x 01 06 01 VV WW 03 02FF
Left| 8x 01 06 01 VV WW 01 03FF
Right| 8x 01 06 01 VV WW 02 03 FF
Upleft| 8x 01 06 01 VV WW 01 01 FF
Upright| 8x 01 06 01 VV WW 02 01FF
DownLeft| 8x 01 06 01 VV WW 01 02FF
DownRight| 8x 01 06 01 VV WW 02 02FF
| Stop| 8x 01 06 01 VV WW 03 03FF|
---|---|---|---
AbsolutePosition| 8x 01 06 02 VV WW 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
RelativePosition| 8x 01 06 03 VV WW 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
Home| 8x 01 06 04 FF
Reset| 8x 01 06 05 FF
Pan-tiltLimitSet| Set| 8x 01 06 07 00 0W 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF| W:1 UpRight 0:DownLeft YYYY: Pan Limit Position(TBD) ZZZZ: Tilt Limit Position(TBD)
Clear| 8x 01 06 07 01 0W 07 0F 0F 0F 07 0F 0F 0F FF

Part3 Inquiry Command

Command| Command Packet| Return Packet|

Note

---|---|---|---
CAM_PowerInq| 8x 09 04 00 FF| y0 50 02 FF| On
y0 50 03 FF| Off(Standby)
CAM_ZoomPosInq| 8x 09 04 47 FF| y0 50 0p 0q 0r 0s FF| pqrs: Zoom Position
CAM_FocusModeInq| 8x 09 04 38 FF| y0 50 02 FF| Auto Focus
y0 50 03 FF| Manual Focus
CAM_FocusPosInq| 8x 09 04 48 FF| y0 50 0p 0q 0r 0s FF| pqrs: Focus Position
CAM_WBModeInq| 8x 09 04 35 FF| y0 50 00 FF| Auto
y0 50 01 FF| Indoor mode
y0 50 02 FF| Outdoor mode
y0 50 03 FF| OnePush mode
y0 50 04 FF| ATW
y0 50 05 FF| Manual
CAM_RGainInq| 8x 09 04 43 FF| y0 50 00 00 0p 0q FF| pq: R Gain
CAM_BGainInq| 8x 09 04 44 FF| y0 50 00 00 0p 0q FF| pq: B Gain
CAM_AEModeInq| 8x 09 04 39 FF| y0 50 00 FF| Full Auto
y0 50 03 FF| Manual
y0 50 0A FF| Shutter priority
y0 50 0B FF| Iris priority
y0 50 0D FF| Bright
CAM_ShutterPosInq| 8x 09 04 4A FF| y0 50 00 00 0p 0q FF| pq: Shutter Position
CAM_IrisPosInq| 8x 09 04 4B FF| y0 50 00 00 0p 0q FF| pq: Iris Position
CAMGainPosiInq| 8x 09 04 4C FF| y0 50 00 00 0p 0q FF| pq: Gain Position
CAM BrightPosiInq| 8x 09 04 4D FF| y0 50 00 00 0p 0q FF| pq: Bright Position
CAM_ExpCompModeInq| 8x 09 04 3E FF| y0 50 02 FF| On
y0 50 03 FF| Off
CAM_ExpCompPosInq| 8x 09 04 4E FF| y0 50 00 00 0p 0q FF| pq: ExpComp Position
CAM_ApertureInq| 8x 09 04 42 FF| y0 50 00 00 0p 0q FF| pq: Aperture Gain
CAM_MemoryInq| 8x 09 04 3F FF| y0 50pp FF| pp: Memory number last operated.
SYS_MenuModeInq| 8x 09 06 06 FF| y0 50 02 FF| On
| | y0 50 03 FF| Off
CAM_LR_ReverseInq| 8x 09 04 61 FF| y0 50 02 FF| On
---|---|---|---
| | y0 50 03 FF| Off
CAM_PictureFlipInq| 8x 09 04 66 FF| y0 50 02 FF| On
| | y0 50 03 FF| Off
CAM_IDInq| 8x 09 04 22 FF| y0 50 0p 0q 0r 0s FF| pqrs: Camera ID
CAM_VersionInq| 8x 09 00 02 FF| y0 50 ab cd mn pq rs tu vw FF|
IR_Transfer| 8x 09 06 1A FF| y0 50 02 FF| On
y0 50 03 FF| Off
Pan-tiltMaxSpeedInq| 8x 09 06 11 FF| y0 50 ww zz FF| ww: PanMaxSpeed zz: Tilt Max Speed
Pan-tiltPosInq| 8x 09 06 12 FF| y0 50 0w 0w 0w 0w 0z 0z 0z 0z FF| wwww: PanPosition zzzz: Tilt Position

Note: 【x】 means the camera address ;【y】=【x + 8】.
VISCA PAN TILT ABSOLUTE POSITION VALUE

Pan Angle| VISCA Value| Tilt Angle|

VISCA Value

---|---|---|---
-170| 0xF670| -30| 0xFE50
-135| 0xF868| 0| 0x0000
-90| 0xFAF0| 30| 0x01B0
-45| 0xFD78| 60| 0x0360
0| 0x0000| 90| 0x510
45| 0x0288| |
90| 0x0510| |
135| 0x0798| |
170| 0x0990| |

VISCA PAN TILT SPEED VALUE

Pan(degree/second)

|

tilt(degree/second)

---|---
0| 0.3| 0| 0.3
1| 1| 1| 1
2| 1.5| 2| 1.5
3| 2.2| 3| 2.2
4| 2.4| 4| 3.6
5| 2.6| 5| 4.7
6| 2.8| 6| 6
7| 3.0| 7| 8
8| 3.2| 8| 10
9| 3.4| 9| 12
10| 3.8| 10| 15
11| 4.5| 11| 18
12| 6| 12| 23
13| 9| 13| 30
14| 15| 14| 39
15| 19| 15| 48
16| 25| 16| 59
17| 32| 17| 69
18| 38| 18| 80
19| 45| |
20| 58| |
21| 75| |
22| 88| |
23| 105| |
24| 120| |
Shutter speed| | 60/30mode| 50/25mode| Iris| |
---|---|---|---|---|---|---
21| 1/10000| 1/10000| 0| close
20| 1/6000| 1/6000| 1| F14
19| 1/4000| 1/3500| 2| F11
18| 1/3000| 1/2500| 3| F9.6
17| 1/2000| 1/1750| 4| F8
16| 1/1500| 1/1250| 5| F6.8
15| 1/1000| 1/1000| 6| F5.6
14| 1/725| 1/600| 7| F4.8
13| 1/500| 1/425| 8| F4
12| 1/350| 1/300| 9| F3.4
11| 1/250| 1/215| 10| F2.8
10| 1/180| 1/150| 11| F2.4
9| 1/125| 1/120| 12| F2
8| 1/100| 1/100| 13| F1.6
7| 1/90| 1/75| |
6| 1/60| 1/50| |
5| 1/30| 1/25| |
4| 1/15| 1/12| |
3| 1/8| 1/6| | |
2| 1/4| 1/3| | |
1| 1/2| 1/2| | |
0| 1/1| 1/1| | |
Gain| 0| 0dB| | Gain| 8| 16dB
1| 2dB| | 9| 18dB
2| 4dB| | 10| 20dB
3| 6dB| | 11| 22dB
4| 8dB| | 12| 24dB
5| 10dB| | 13| 26dB
6| 12dB| | 14| 28dB
7| 14dB| | 15| 30dB

PELCO-D PROTOCOL

Function| Byte1| Byte2| Byte3| Byte4| Byte5| Byte6|

Byte7

---|---|---|---|---|---|---|---
Up| 0xFF| Address| 0x00| 0x08| Pan Speed| Tilt Speed| SUM
Down| 0xFF| Address| 0x00| 0x10| Pan Speed| Tilt Speed| SUM
Left| 0xFF| Address| 0x00| 0x04| Pan Speed| Tilt Speed| SUM
Right| 0xFF| Address| 0x00| 0x02| Pan Speed| Tilt Speed| SUM
Up left| 0xFF| Address| 0x00| 0x0C| Pan Speed| Tilt Speed| SUM
Upright| 0xFF| Address| 0x00| 0x0A| Pan Speed| Tilt Speed| SUM
Down Left| 0xFF| Address| 0x00| 0x14| Pan Speed| Tilt Speed| SUM
Down Right| 0xFF| Address| 0x00| 0x12| Pan Speed| Tilt Speed| SUM
Zoom In| 0xFF| Address| 0x00| 0x20| 0x00| 0x00| SUM
Zoom Out| 0xFF| Address| 0x00| 0x40| 0x00| 0x00| SUM
Focus Far| 0xFF| Address| 0x00| 0x80| 0x00| 0x00| SUM
Focus Near| 0xFF| Address| 0x01| 0x00| 0x00| 0x00| SUM
Set Preset| 0xFF| Address| 0x00| 0x03| 0x00| Preset ID| SUM
Clear Preset| 0xFF| Address| 0x00| 0x05| 0x00| Preset ID| SUM
Call Preset| 0xFF| Address| 0x00| 0x07| 0x00| Preset ID| SUM
Query Pan Position| 0xFF| Address| 0x00| 0x51| 0x00| 0x00| SUM
Query Pan Position Response| 0xFF| Address| 0x00| 0x59| Value High Byte| Value Low Byte| SUM
Query Tilt Position| 0xFF| Address| 0x00| 0x53| 0x00| 0x00| SUM
Query Tilt Position Response| 0xFF| Address| 0x00| 0x5B| Value High Byte| Value Low Byte| SUM
Query Zoom Position| 0xFF| Address| 0x00| 0x55| 0x00| 0x00| SUM
Query Zoom Position Response| 0xFF| Address| 0x00| 0x5D| Value High Byte| Value Low Byte| SUM
Up| 0xA0| Address| 0x00| 0x08| Pan Speed| Tilt Speed| 0xAF| XOR
---|---|---|---|---|---|---|---|---
Down| 0xA0| Address| 0x00| 0x10| Pan Speed| Tilt Speed| 0xAF| XOR
Left| 0xA0| Address| 0x00| 0x04| Pan Speed| Tilt Speed| 0xAF| XOR
Right| 0xA0| Address| 0x00| 0x02| Pan Speed| Tilt Speed| 0xAF| XOR
Up left| 0xA0| Address| 0x00| 0x0C| Pan Speed| Tilt Speed| 0xAF| XOR
Upright| 0xA0| Address| 0x00| 0x0A| Pan Speed| Tilt Speed| 0xAF| XOR
Down Left| 0xA0| Address| 0x00| 0x14| Pan Speed| Tilt Speed| 0xAF| XOR
Down Right| 0xA0| Address| 0x00| 0x12| Pan Speed| Tilt Speed| 0xAF| XOR
Zoom In| 0xA0| Address| 0x00| 0x20| 0x00| 0x00| 0xAF| XOR
Zoom Out| 0xA0| Address| 0x00| 0x40| 0x00| 0x00| 0xAF| XOR
Focus Far| 0xA0| Address| 0x00| 0x80| 0x00| 0x00| 0xAF| XOR
Focus Near| 0xA0| Address| 0x01| 0x00| 0x00| 0x00| 0xAF| XOR
Set Preset| 0xA0| Address| 0x00| 0x03| 0x00| Preset ID| 0xAF| XOR
Clear Preset| 0xA0| Address| 0x00| 0x05| 0x00| Preset ID| 0xAF| XOR
Call Preset| 0xA0| Address| 0x00| 0x07| 0x00| Preset ID| 0xAF| XOR
Query Pan Position| 0xA0| Address| 0x00| 0x51| 0x00| 0x00| 0xAF| XOR
Query Pan Position Response| 0xA0| Address| 0x00| 0x59| Value High Byte| Value Low Byte| 0xAF| XOR
Query Tilt Position| 0xA0| Address| 0x00| 0x53| 0x00| 0x00| 0xAF| XOR
Query Tilt Position Response| 0xA0| Address| 0x00| 0x5B| Value High Byte| Value LowByte| 0xAF| XOR
Query Zoom Position| 0xA0| Address| 0x00| 0x55| 0x00| 0x00| 0xAF| XOR
Query Zoom Position Response| 0xA0| Address| 0x00| 0x5D| Value High Byte| Value Low Byte| 0xAF| XOR

IR TRANSFER(IR PASS)

1. Currently the camera support NEC code format. For customized with other codes, pls contact us.

2. Once the camera finish power configuration, enable the IR transfer function via sending COM command.

3. Get the targeted remote controller point to the camera IR receiver, press keys on the remote controller, then the camera will output the received IR code via VISCA IN port.

4. IR Transfer output format: XX XX XX XX FF
   XX XX XX XX: Remote Controller Code ……….. FF: End Code

5. The camera can save all setting, no need to re-set after power circle.

OSD MENU

1. under working mode, press the menu button on the IR remote, to enter the OSD menu; press the menu button again to exit and save modified parameters.             
2. Use the navigate button to select the main menu. As above picture, once been selected, the main menu will change to grey color background, and the right side will show all parameters under this sub menu.
3. In the second grade menu, press the up/down navigate button to select the sub menu, use left/right navigate button to set the parameter.
4. Select the last option “return” and press the right navigate button to get back to previous menu.
5. Press OSD button again to exit the menu.
6. OSD Menu List& Defaulted Setting.

CAMERA SET

| LANGUAGE| ENGLISH/CHINESE|
---|---|---|---
PROTOCOL| VISCA/PELCO-P/PELCO-D| Default: VISCA
ADDRESS| VISCA:1~7
PELCO-P/D:1~7| Default: 1
BAUD RATE| 2400/9600/115200| Default: 9600
PARITY BIT| NONE|
RETURN| Return to previous menu|
FOCUS| FOCUS MODE| AUTO/MANU/PUSH| Default: AUTO
---|---|---|---
SENSITIVITY| Focus Sensitivity setting: LOW/MID/HIGH| Default: MID
FOCUS LIMIT| The target distance: 1.5M/2M/3M/6M/10M| Default: 1.5M
D_ZOOM| Digital Zoom: OFF/ON| Default: OFF
ZOOM SPEED| Set zoom speed level:0~7| Default: 7
LENS INIT| Lens focus parameter frequency setting, choose EXE to start the lens focus reset| Default: OFF
DIS ZOOM RATIO| Display zoom value during zooming control| Default: OFF
RETURN| Return to previous menu|
WB MODE| WB MODE| Set White Balance mode| Default: ATW
---|---|---|---
B_GAIN| Set blue gain under manual mode| Default: 52
R_GAIN| Set red gain under manual mode| Default: 58
RETURN| Return to previous menu|
EXPOSURE| EXP MODE| AUTO、MANU、IRIS、SHUT、BRI.| Default: AUTO
---|---|---|---
SHUT TIME| Set shutter speed: 1/1~1/10000
Only available under MANU or SHUT mode| Default: 1/100
IRIS| Set iris value: 0~13, only available under MANU or IRIS mode| Default: 10
GAIN| Set gain value: 0~15, only available under MANU mode| Default: 0
BRIGHT| Set bright value: 0~27 , only available under BRI. mode| Default: 11
| SLOW SHUT| Slow shutter set: OFF/ON| Default: OFF
---|---|---|---
FLICK| 50HZ/60HZ/OFF| Default: 60HZ
RETURN| Return to previous menu|
PICTURE| BRIGHTNESS| Set brightness value: 0~15| Default: 8
---|---|---|---
SHARPNESS| Set sharpness value:：0~15| Default: 3
CONSTRAST| Set contrast value: 0~15| Default: 8
SATURATION| Set saturation value: 0~15, the higher value, the stronger color| Default: 9
MIRROR| Left/right flip: ON/OFF| Default: OFF
PIC FLIP| Up/down flip: ON/OFF| Default: OFF
FREEZE| ON/OFF| Default: OFF
DEFOG| Set image permeability| Default: 2
RETURN| Return to previous menu|
IMAGE ENHANCE| 2D NR| ON/OFF| Default: OFF
---|---|---|---
3D NR| OFF/AUTO/1~4| Default: AUTO
D_WDR| Set dynamic level : OFF/1~6| Default: OFF
GAMMA| Set gamma: 0~4| Default: 0
BACKLIGHT| ON/OFF| Default: OFF
HIGHLIGHT| ON/OFF| Default: OFF
RETURN| Return to previous menu|
MASK| MASK SWITCH| Privacy zone function: ON/OFF| Default: OFF
---|---|---|---
COLOUR| Set mask zone color: WHITE/YELLOW/GRAY/GREEN/VIOLET/RED| Default: WHITE
INDEX| Set mask zone number: 1~8| Default: 1
INDEX SWITCH| Set index zone: ON/OFF| Default: OFF
ROW START| Set current mask zone’s row start position| Default: 0
ROW END| Set current mask zone’s row end position| Default: 479
LINE START| Set current mask zone’s line start position| Default: 0
LINE END| Set current mask zone’s line end position| Default: 539
RETURN| Return to previous menu|
D/N MODE| D/N MODE| Set D/N mode: DAY/NIGHT/AUTO| Default: DAY
---|---|---|---
DAY TO NIGHT| Set day to night brightness threshold value| Default: 200
NIGH TO DAY| Set night to day brightness threshold value| Default: 25
SWITCH DELAY| Set switch delay between different mode, to avoid repeat switching under AUTO mode: 1~60s| Default: 1
GAIN LIMIT| Gain limit under low light:2/4/6/8/11/16/32/64/128/256/320/511| Default: 511
RETURN| Return to previous menu|
CAMERA INF.| IMAGE VER.| Image firmware version
---|---|---
IMAGE DATE| Image firmware release date: YY.MM.DD
CONTROL VER.| Control firmware version
CONTROL DATE| Control firmware release date: YY.MM.DD
BAUDRATE| Current baud rate value
PARITY BIT| Current control protocol parity bit value
FRAMERATE| Current video resolution and frame rate
RETURN| Return to previous menu
RESET| REEST to defaulted value (except the Language): ON/OFF
---|---

UVC CONTROL

| Control Requests| Control Selector
---|---|---
1| Brightness Control| PU_BRIGHTNESS_CONTROL
2| Contrast Control| PU_CONTRAST_CONTROL
3| Hue Control| PU_HUE_CONTROL
4| Saturation Control| PU_SATURATION_CONTROL
5| Sharpness Control| PU_SHARPNESS_CONTROL
6| Gamma Control| PU_GAMMA_CONTROL
7| White Balance Temperature Control| PU_WHITE_BALANCE_TEMPERATURE_CONTROL
8| Gain Control| PU_GAIN_CONTROL
9| Power Line Frequency Control| PU_POWER_LINE_FREQUENCY_CONTROL
10| Zoom (Absolute) Control| CT_ZOOM_ABSOLUTE_CONTROL
11| Zoom (Relative) Control| CT_ZOOM_RELATIVE_CONTROL
12| Pan Tilt (Absolute) Control| CT_PANTILT_ABSOLUTE_CONTROL
13| Pan Tilt (Relative) Control| CT_PANTILT_RELATIVE_CONTROL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>