TELYCAM TLC-1000-U3S USB3.0 HD Video Camera User Manual
- June 12, 2024
- Telycam
Table of Contents
- SAFETY GUIDES
- ACCESSORIES
- QUICK START
- PRODUCT HIGHLIGHTS
- PRODUCT SPEC
- CAMERA INTERFACE
- CAMERA DIMENSION(MM)
- IR REMOTE CONTROLLER
- LEARNING FUNCTION
- VISCA IN (RS232) PORT
- VISCA PROTOCOL
- PELCO-D PROTOCOL
- PELCO-P PROTOCOL
- OSD MENU
- UVC CONTROL
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
TELYCAM TLC-1000-U3S USB3.0 HD Video Camera
SAFETY GUIDES
- Before operation, please fully read and follow all instructions in the manual. For your safety, always keep this manual with the camera.
- The camera power input range is 100-240VAC(50-60Hz),ensure the power supply input within this rate before powering on.
- The camera power voltage is 12VDC, rated currency is 1.5A. We suggest you use it with the original power supply adapter supplied by the factory.
- Please keep the power cable, video cable and control cable in a safe place. Protect all cables especially the connectors.
- Operational environment: 0℃-50℃, humidity less than 90%.To avoid any danger, do not put anything inside the camera, and keep away from the corrosive liquid.
- Avoid stress, vibration and damp during transportation, storage and installation.
- Do not dismantle the camera housing and cover. For any service, please contact authorized technicians.
- RF cable and control cable should be individually shielded, and cannot be substituted with other cables. Do not direct the camera lens towards strong light, such as the sun or the intensive light.
- Use a dry and soft cloth to clean the camera housing. Applied with neutral cleaning agent when there is need to clean. To avoid damage on the camera lens, never use strong or abrasive cleaning agents on the camera housing.
- Do not move the camera by holding the camera head. To avoid mechanical trouble, do not rotate the camera head by hand.
- Put the camera on fixed and smooth desk or platform, avoid leaned installation.
- Power Supply Polarity(Drawing).
Note:
The camera video may be affected when the electromagnetic fields is at specific frequency
ACCESSORIES
Check all bellow items when open the package:
Camera········································································
1
Power Adapter································································
1
Power Cable··································································
1
RS232 Control Cable························································ 1
USB3.0 Cable……………………………………………………..…. 1
Remote Controller··························································· 1
User Manual··································································
1
Double-sided Adhesive…………………………………………..….. 1
QUICK START
-
Check all cable connections before power on.
-
DIP Switch Setting (at the bottom of the camera):
Function(ARM)| SW-1| SW-2| Instruction
1| OFF| OFF| Updating mode
2| ON| OFF| Debugging mode
3| OFF| ON| Undefined
4| ON| ON| Working mode
Function| SW-3| SW-4| Instruction
1| OFF| OFF| Working mode
2| ON| OFF| Undefined
3| OFF| ON| Undefined
4| ON| ON| Undefined
Function(USB)| SW-5| SW-6| Instruction
1| OFF| OFF| Working mode
2| ON| OFF| Updating mode
3| OFF| ON| Undefined
4| ON| ON| Updating mode
PRODUCT HIGHLIGHTS
- Smart and fashion design, ideal for cloud-based conferencing.
- Adopts advanced DSP, 1/2.8 inch 5MP image sensor, and high quality 10X 62.5degree FOV optical lens, provides fluent and crystal image quality.
- Fast switching between different video formats: less than 1 second.
- 10X Optical Zoom + 12XDigital Zoom.
- Fast and accurate focus performance.
- Easy firmware upgrade-(field-up gradable).
- USB3.0 super speed output, USB2.0 compatible.
- Effective RS232/485 serial control.
- Up to 128 presets.
- Compatible with the majority of videoconferencing software (UVC1.5 protocol standard).
- With powerful functional remote controller.
- IR transfer/IR pass function: except receiving the camera remote controller signal, the camera can also receive other codec’s IR remote control signal, and pass these IR control signal to the codec’s IR receiver (via VISCA IN port).
- Multi-language OSD menu: English, Chinese.
PRODUCT SPEC
Video Format| USB3.0| 1080P30/25, 720P60/50/30/25/15, 720576P30, 704576P30,
640480P30/25, 352288P30, 320240P30, 176144P30, 160120P30
---|---|---
USB2.0| 720P15, 720576P30, 704576P30, 640480P30/25, 352288P30, 320240P30,
176144P30, 160120P30
Video Port| USB3.0&USB2.0
Sensor| 1/2.8 inch high quality 5MP CMOS sensor
Lens| F4.7~47.mm(10X), F1.8 – 14, Field of view: 62.5°(wide)-6.43°(tele)
Pan/tilt Rotation| Pan:±170°; Tilt:-30°~+90°, support up-side down
installation
Pan/tilt Speed| Pan: 0.1°-120°/s; Tilt: 0.1°-80°/s
Preset| 10 via IR remote setting, 128 via VISCA control, preset accuracy :0.1°
Control Port| RS232/RS485 , USB3.0/USB2.0
Min. Lux| 0.01 Lux
White Balance| ATWB/MANUAL/SOD./FL./AEB/IDR./ODR./PUSH
Focus| AUTO/MANUAL/PUSH
Iris| AUTO/MANUAL/IRIS
Shutter| AUTO/MANUAL/SHUT
WDR| Supported
BLC| Supported
2D Noise Reduction| Supported
3D Noise Reduction| Supported
Input Voltage| 12VDC
Dimension| 148mm×132mm×162mm
Net weight| 0.9KGS(2LBS)
CAMERA INTERFACE
- Camera Lens
- Camera Base
- IR Receiver Pane
- Indicator Light
- Dial Switch
- Tripod Screw Hole
- Installation Hole
- Power Indicator light(red)
- 12VDC Power Input
- RS232(VISCA IN) Port
- USB3.0 Port
CAMERA DIMENSION(MM)
IR REMOTE CONTROLLER
LED Function Instruction
Press any button and shows in red color: Current selection is to control the
camera.
Press any button and shows in green color: Current selection is to control the
codec.
Press any button and shows in blue color: Current selection is to control the
TV.
Power button
Red button : in normal work mode, short press one time, camera will enter
standby mode; short press again, the camera will start self-configuration and
go to HOME position; it will go to No.0 preset position if that was set.
Green button : Codec power button(need to learn the button coding).
Blue button : TV power button( need to learn the button coding).
Menu button:
Enter the OSD menu.
Focus (Left): +/-
Manual focus, only valid under manual focus model.
Zoom (Right): +/-
Control the lens zoom rate.
Navigate : Up/Down/Left/Right
In normal working mode, use navigate key to control pan/tilt.
Confirm/Home button:
In normal working mode, short press to let the camera go back to Home
position.
Number buttons:
Set Preset: Long press(3seconds) the number button to save preset.
Clear Preset : +number button to clear the relative preset.
Long press(3seconds) the Clear button to clear all preset.
Run Preset : Short press the number button to run the relative preset.
LEARNING FUNCTION
-
Press the green button, the LED indicator light will show in green color for 1 second, means switch to video terminal/codec control mode.
-
Single Button Coding: long press(3 seconds) Home +number”1″ button simultaneously, the green indicator LED will light, enter button learning mode, press the buttons which need to be learned, LED will start flickering(1HZ), now can start button learning: get the codec remote point to the camera remote’s infrared tube( about 10 cm distance), then press the button which need to be learned, the LED re-flickering when learning finishes ; press other buttons which also need to be learned; Press the Home+”0″ buttons simultaneously to exit and save all remote data.
If the button learning fails, the camera will enter normal working mode after 15 seconds, LED will extinguish. -
All Button Coding: long press (3 seconds) Home+number”2″ button simultaneously, the green indicator LED will start flickering(1HZ), to enter all button learning mode: get codec remote point to the camera remote’s infrared tube( about 10cm distance), to start all button coding mode, the LED will extinguish when learning finished. If the button learning fails, the camera will enter normal working mode after 15 seconds, LED will extinguish.
-
All Button Sending Mode: long press (3 seconds) the Menu+ number “3” button simultaneously, the remote will enter all button sending mode.
-
Similar operation for the TV control mode learning.
VISCA IN (RS232) PORT
No. | Function |
---|---|
1 | DTR |
2 | DSR |
3 | TXD |
4 | GND |
5 | RXD |
6 | A |
7 | IR OUT |
8 | B |
VISCA IN &RS485 Connection
Camera VISCA IN | RS485 |
---|---|
1 | DTR |
2 | DSR |
3 | TXD |
4 | GND |
5 | RXD |
6 | A(+) |
7 | IR OUT |
8 | B(-) |
VISCA IN &DB9 Connection
Camera VISCA IN | Windows DB-9 |
---|---|
1 | DTR |
2 | DSR |
3 | TXD |
4 | GND |
5 | RXD |
6 | A(+) |
7 | IR OUT |
8 | B(-) |
SERIAL PORT CONFIGURATION:
Parameter | Value | Parameter | Value |
---|---|---|---|
Baud rate | 2400/4800/9600/115200 | Stop Bit | 1bit |
Start Bit | 1 bit | Verify Bit | None |
Date Bit | 8 bit |
VISCA PROTOCOL
Part1 Camera Return Command
Ack/Completion Message
| Command Packet| Note
ACK| z0 41 FF| Returned when the command is accepted.
Completion| z0 51 FF| Returned when the command has been executed.
z = camera adderss+8
Error Messages
| Command Packet| Note
Syntax Error| z0 60 02 FF| Returned when the command format is different or
when a command with illegal command parameters is accepted
Command Not Executable| z0 61 41 FF| Returned when a command cannot be
executed due to current conditions. For example, when commands controlling the
focus manually are received during auto focus.
Part2 Camera Control Command
Command | Function | Command Packet | Note |
---|---|---|---|
Address Set | Broadcast | 88 30 01 FF | Address setting |
IF_Clear | Broadcast | 88 01 00 01 FF | I/F Clear |
CAM_Power | On | 8x 01 04 00 02 FF | Power ON/OFF |
Off | 8x 01 04 00 03 FF | ||
CAM_Zoom | Stop | 8x 01 04 07 00 FF | |
Tele(Standard) | 8x 01 04 07 02 FF | ||
Wide(Standard) | 8x 01 04 07 03 FF | ||
Tele(Variable) | 8x 01 04 07 2p FF | p = 0(low)~7(high) | |
Wide(Variable) | 8x 01 04 07 3p FF | ||
Direct | 8x 01 04 47 0p 0q 0r 0s FF | pqrs: Zoom Position |
(0(wide) ~0x4000(tele))
CAM_Focus| Stop| 8x 01 04 08 00 FF|
Far(Standard)| 8x 01 04 08 02 FF
Near(Standard)| 8x 01 04 08 03 FF
Direct| 8x 01 04 48 0p 0q 0r 0s FF| pqrs: Focus Position
One Push AF| 8x 01 04 18 01 FF|
CAM_Zoom Focus| Direct| 8x 01 04 47 0p 0q 0r 0s 0t 0u 0v 0w FF| pqrs: Zoom
Position (0(wide)~ 0x4000(tele))
tuvw: Focus Position
CAM_WB| Auto| 8x 01 04 35 00 FF|
Indoor| 8x 01 04 35 01 FF|
Outdoor| 8x 01 04 35 02 FF|
One Push| 8x 01 04 35 03 FF|
| ATW| 8x 01 04 35 04FF|
Manual| 8x 01 04 35 05 FF|
Sodium Lamp| 8x 01 04 35 08 FF|
Fluorescent lamp| 8x 01 04 35 09 FF|
CAM_R Gain| Reset| 8x 01 04 03 00 FF| Manual Control of R Gain
Up| 8x 01 04 03 02 FF
Down| 8x 01 04 03 03 FF
Direct| 8x 01 04 43 00 00 0p 0q FF| pq: R Gain (0~0xFF)
CAM_B gain| Reset| 8x 01 04 04 00 FF| Manual Control of B Gain
Up| 8x 01 04 04 02 FF
Down| 8x 01 04 04 03 FF
Direct| 8x 01 04 44 00 00 0p 0q FF| pq: B Gain (0-0xFF)
CAM_AE| Full Auto| 8x 01 04 39 00 FF| Automatic Exposure mode
Manual| 8x 01 04 39 03 FF| Manual Control mode
Shutter Priority| 8x 01 04 39 0A FF| Shutter Priority mode
Iris Priority| 8x 01 04 39 0B FF| Iris Priority mode
Bright| 8x 01 04 39 0D FF| Bright mode(Manual control)
CAM_Shutter| Reset| 8x 01 04 0A 00 FF| Shutter Setting
Up| 8x 01 04 0A 02 FF
Down| 8x 01 04 0A 03 FF
Direct| 8x 01 04 4A 00 00 0p 0q FF| pq: Shutter Position
(0~0x15)
CAM_Iris| Reset| 8x 01 04 0B 00 FF| Iris Setting
Up| 8x 01 04 0B 02 FF
Down| 8x 01 04 0B 03 FF
Direct| 8x 01 04 4B 00 00 0p 0q FF| pq: Iris Position (0~ 0x11)
CAM_Gain| Reset| 8x 01 04 0C 00 FF| Gain Setting
Up| 8x 01 04 0C 02 FF
Down| 8x 01 04 0C 03 FF
Direct| 8x 01 04 0C 00 00 0p 0q FF| pq: Gain Position (0~0x0E)
CAM_Bright| Reset| 8x 01 04 0D 00 FF| Bright Setting
Up| 8x 01 04 0D 02 FF
Down| 8x 01 04 0D 03 FF
Direct| 8x 01 04 4D 00 00 0p 0q FF| pq: Bright l Position ()
CAM_WDR| On| 8x 01 04 3D 02 FF| WDR ON/OFF
| Off| 8x 01 04 3D 03 FF|
Direct| 8x 01 04 D3 0p FF| pq: WDR Position (1~0x06)
CAM_BackLight| On| 8x 01 04 33 02 FF| BackLight On
Off| 8x 01 04 33 03 FF| BackLight Off
CAM_Sharpness| Reset| 8x 01 04 02 00 FF| Sharpness Control
Up| 8x 01 04 02 02 FF
Down| 8x 01 04 02 03 FF
Direct| 8x 01 04 42 00 00 0p 0q FF| pq: Aperture Gain (0~0x04)
CAM_Preset| Reset| 8x 01 04 3F 00 0p FF| p: Preset Number(=0 to 127)
Corresponds to 0 to 9 on the Remote Commander
Set| 8x 01 04 3F 01 0p FF
Recall| 8x 01 04 3F 02 0p FF
CAM_LR_Reverse| On| 8x 01 04 61 02 FF| Image Flip Horizontal ON/OFF
Off| 8x 01 04 61 03 FF
CAM_Picture Flip| On| 8x 01 04 66 02 FF| Image Flip Vertical ON/OFF
Off| 8x 01 04 66 03 FF
CAM_Mount Mode| UP| 8x 01 04 A4 02 FF| Mount Up
Down| 8x 01 04 A4 03 FF| Mount Down
CAM_Saturation| Direct| 8x 01 04 A1 00 00 00 0p FF| (0~0x0E)
CAM_2D
Noise Reduction
| Direct| 8x 01 04 53 0p FF| (0~0x05)
CAM_3D
Noise Reduction| Direct| 8x 01 04 54 0p FF| (0~0x03)
CAM_New Bright| Direct| 81 01 04 A4 00 00 0p 0q FF| (0~0x0F)
CAM_Constrast| Direct| 81 01 04 A2 00 00 0p 0q FF| (0~0x0F)
CAM_Gamma| Direct| 8x 01 04 5B 0p FF| (0~0x04)
FLICK| Off| 81 01 04 23 00 FF|
50HZ| 81 01 04 23 01 FF|
60HZ| 81 01 04 23 02 FF|
SYS_Menu| Menu On| 8x 01 06 06 02 FF| Turn on the menu
Menu Off| 8x 01 06 06 03 FF| Turn off the menu
IR_Transfer| Transfer On| 8x 01 06 1A 02 FF| Receive IR(remote commander) CODE
from
VISCA communication ON/OFF
Transfer Off| 8x 01 06 1A 03 FF
IR_Receive| On| 8x 01 06 08 02 FF| IR(remote commander)receive ON/OFF
Off| 8x 01 06 08 03 FF
On/Off| 8x 01 06 08 10 FF
Pan_tilt Drive| Up| 8x 01 06 01 VV WW 03 01 FF| VV: Pan speed 0x01 (low speed)
to 0x18 (high speed) WW: Tilt speed 0x01 (low speed) to 0x14 (high speed)
YYYY: Pan Position(TBD) ZZZZ: Tilt Position(TBD)
Down| 8x 01 06 01 VV WW 03 02 FF
Left| 8x 01 06 01 VV WW 01 03 FF
Right| 8x 01 06 01 VV WW 02 03 FF
Up left| 8x 01 06 01 VV WW 01 01 FF
Up right| 8x 01 06 01 VV WW 02 01 FF
Down Left| 8x 01 06 01 VV WW 01 02 FF
Down Right| 8x 01 06 01 VV WW 02 02 FF
Stop| 8x 01 06 01 VV WW 03 03 FF
Absolute Position| 8x 01 06 02 VV WW
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
Relative Position| 8x 01 06 03 VV WW
0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF
Home| 8x 01 06 04 FF
Reset| 8x 01 06 05 FF
Pan-tilt Limit Set| Set| 8x 01 06 07 00 0W 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF| W:1 Up
Right 0:Down Left YYYY: Pan Limit Position(TBD) ZZZZ: Tilt Limit Position(TBD)
Clear| 8x 01 06 07 01 0W 07 0F 0F 0F 07 0F 0F 0F FF
Part3 Inquiry Command
Command | Command Packet | Return Packet | Note |
---|---|---|---|
CAM_Power Inq | 8x 09 04 00 FF | y0 50 02 FF | On |
y0 50 03 FF | Off(Standby) | ||
CAM_Zoom Pos Inq | 8x 09 04 47 FF | y0 50 0p 0q 0r 0s FF | pqrs: Zoom Position |
CAM_Focus Mode Inq | 8x 09 04 38 FF | y0 50 02 FF | Auto Focus |
y0 50 03 FF | Manual Focus | ||
CAM_Focus Pos Inq | 8x 09 04 48 FF | y0 50 0p 0q 0r 0s FF | pqrs: Focus Position |
CAM_WB Mode Inq | 8x 09 04 35 FF | y0 50 00 FF | Auto |
y0 50 01 FF | Indoor mode | ||
y0 50 02 FF | Outdoor mode | ||
y0 50 03 FF | One Push mode | ||
y0 50 04 FF | ATW | ||
y0 50 05 FF | Manual | ||
CAM_R Gain Inq | 8x 09 04 43 FF | y0 50 00 00 0p 0q FF | pq: R Gain |
CAM_B Gain Inq | 8x 09 04 44 FF | y0 50 00 00 0p 0q FF | pq: B Gain |
CAM_AE Mode Inq | 8x 09 04 39 FF | y0 50 00 FF | Full Auto |
y0 50 03 FF | Manual | ||
y0 50 0A FF | Shutter priority | ||
y0 50 0B FF | Iris priority | ||
y0 50 0D FF | Bright | ||
CAM_Shutter Pos Inq | 8x 09 04 4A FF | y0 50 00 00 0p 0q FF | pq: Shutter |
Position
CAM_Iris Pos Inq| 8x 09 04 4B FF| y0 50 00 00 0p 0q FF| pq: Iris Position
CAMGain Posi Inq| 8x 09 04 4C FF| y0 50 00 00 0p 0q FF| pq: Gain Position
CAM Bright Posi Inq| 8x 09 04 4D FF| y0 50 00 00 0p 0q FF| pq: Bright
Position
CAM_Exp Comp Mode Inq| 8x 09 04 3E FF| y0 50 02 FF| On
y0 50 03 FF| Off
CAM_Exp Comp Pos Inq| 8x 09 04 4E FF| y0 50 00 00 0p 0q FF| pq: Exp Comp
Position
CAM_Aperture Inq| 8x 09 04 42 FF| y0 50 00 00 0p 0q FF| pq: Aperture Gain
CAM_Memory Inq| 8x 09 04 3F FF| y0 50pp FF| pp: Memory number last operated.
SYS_Menu Mode Inq| 8x 09 06 06 FF| y0 50 02 FF| On
| | y0 50 03 FF| Off
CAM_LR_Reverse Inq| 8x 09 04 61 FF| y0 50 02 FF| On
| | y0 50 03 FF| Off
CAM_Picture Flip Inq| 8x 09 04 66 FF| y0 50 02 FF| On
| | y0 50 03 FF| Off
CAM_Version Inq| 8x 09 00 02 FF| y0 50 ab cd
mn pq rs tu vw FF
|
IR_Transfer| 8x 09 06 1A FF| y0 50 02 FF| On
y0 50 03 FF| Off
IR_Receive| 8x 09 06 08 FF| y0 50 02 FF| On
y0 50 03 FF| Off
IR_Receive Return| | y0 07 7D 01 04 00 FF| Power ON/OFF
y0 07 7D 01 04 07 FF| Zoom tele/wide
y0 07 7D 01 04 38 FF| AF On/Off
y0 07 7D 01 04 33 FF| CAM_Backlight
y0 07 7D 01 04 3F FF| CAM_Memory
y0 07 7D 01 06 01 FF| Pan_tilt Drive
Pan-tilt Pos Inq| 8x 09 06 12 FF| y0 50 0w 0w 0w 0w 0z 0z 0z 0z FF| wwww: Pan
Position zzzz: Tilt Position
Note:【x】 means the camera address ;【y】=【x + 8】.
VISCA PAN TILT ABSOLUTE POSITION VALUE
Pan Angle | VISCA Value | Tilt Angle | VISCA Value |
---|---|---|---|
-170 | 0xF670 | -30 | 0xFE50 |
-135 | 0xF868 | 0 | 0x0000 |
-90 | 0xFAF0 | 30 | 0x01B0 |
-45 | 0xFD78 | 60 | 0x0360 |
0 | 0x0000 | 90 | 0x510 |
45 | 0x0288 | ||
90 | 0x0510 | ||
135 | 0x0798 | ||
170 | 0x0990 |
VISCA PAN TILT SPEED VALUE
Pan(degree/second) | tilt(degree/second) |
---|---|
0 | 0.3 |
1 | 1 |
2 | 1.5 |
3 | 2.2 |
4 | 2.4 |
5 | 2.6 |
6 | 2.8 |
7 | 3.0 |
8 | 3.2 |
9 | 3.4 |
10 | 3.8 |
11 | 4.5 |
12 | 6 |
13 | 9 |
14 | 15 |
15 | 19 |
16 | 25 |
17 | 32 |
18 | 38 |
19 | 45 |
20 | 58 |
21 | 75 |
22 | 88 |
23 | 105 |
24 | 120 |
Shutter speed | |
--- | --- |
21 | 1/10000 |
20 | 1/6000 |
19 | 1/4000 |
18 | 1/3000 |
17 | 1/2000 |
16 | 1/1500 |
15 | 1/1000 |
14 | 1/725 |
13 | 1/500 |
12 | 1/350 |
11 | 1/250 |
10 | 1/180 |
9 | 1/125 |
8 | 1/100 |
7 | 1/90 |
6 | 1/60 |
5 | 1/30 |
4 | 1/15 |
3 | 1/8 |
2 | 1/4 |
1 | 1/2 |
0 | 1/1 |
Gain | 0 |
1 | 2dB |
2 | 4dB |
3 | 6dB |
4 | 8dB |
5 | 10dB |
6 | 12dB |
7 | 14dB |
PELCO-D PROTOCOL
Function| Byte1| Byte2| Byte3| Byte4| Byte5|
Byte6| Byte7
---|---|---|---|---|---|---|---
Up| 0xFF| Address| 0x00| 0x08| Pan Speed| Tilt Speed| SUM
Down| 0xFF| Address| 0x00| 0x10| Pan Speed| Tilt Speed| SUM
Left| 0xFF| Address| 0x00| 0x04| Pan Speed| Tilt Speed| SUM
Right| 0xFF| Address| 0x00| 0x02| Pan Speed| Tilt Speed| SUM
Up left| 0xFF| Address| 0x00| 0x0C| Pan Speed| Tilt Speed| SUM
Upright| 0xFF| Address| 0x00| 0x0A| Pan Speed| Tilt Speed| SUM
Down Left| 0xFF| Address| 0x00| 0x14| Pan Speed| Tilt Speed| SUM
Down Right| 0xFF| Address| 0x00| 0x12| Pan Speed| Tilt Speed| SUM
Zoom In| 0xFF| Address| 0x00| 0x20| 0x00| 0x00| SUM
Zoom Out| 0xFF| Address| 0x00| 0x40| 0x00| 0x00| SUM
Focus Far| 0xFF| Address| 0x00| 0x80| 0x00| 0x00| SUM
Focus Near| 0xFF| Address| 0x01| 0x00| 0x00| 0x00| SUM
Set Preset| 0xFF| Address| 0x00| 0x03| 0x00| Preset ID| SUM
Clear Preset| 0xFF| Address| 0x00| 0x05| 0x00| Preset ID| SUM
Call Preset| 0xFF| Address| 0x00| 0x07| 0x00| Preset ID| SUM
Query Pan Position| 0xFF| Address| 0x00| 0x51| 0x00| 0x00| SUM
Query Pan Position
Response
| 0xFF| Address| 0x00| 0x59| Value High
Byte
| Value Low
Byte
| SUM
Query Tilt Position| 0xFF| Address| 0x00| 0x53| 0x00| 0x00| SUM
Query Tilt Position
Response
| 0xFF| Address| 0x00| 0x5B| Value High
Byte
| Value Low
Byte
| SUM
Query Zoom Position| 0xFF| Address| 0x00| 0x55| 0x00| 0x00| SUM
Query Zoom Position
Response
| 0xFF| Address| 0x00| 0x5D| Value High
Byte
| Value Low
Byte
| SUM
PELCO-P PROTOCOL
Function | Byte1 | Byte2 | Byte3 | Byte4 | Byte5 | Byte6 | Byte7 | Byte8 |
---|---|---|---|---|---|---|---|---|
Up | 0xA0 | Address | 0x00 | 0x08 | Pan Speed | Tilt Speed | 0xAF | XOR |
Down | 0xA0 | Address | 0x00 | 0x10 | Pan Speed | Tilt Speed | 0xAF | XOR |
Left | 0xA0 | Address | 0x00 | 0x04 | Pan Speed | Tilt Speed | 0xAF | XOR |
Right | 0xA0 | Address | 0x00 | 0x02 | Pan Speed | Tilt Speed | 0xAF | XOR |
Up left | 0xA0 | Address | 0x00 | 0x0C | Pan Speed | Tilt Speed | 0xAF | XOR |
Upright | 0xA0 | Address | 0x00 | 0x0A | Pan Speed | Tilt Speed | 0xAF | XOR |
Down Left | 0xA0 | Address | 0x00 | 0x14 | Pan Speed | Tilt Speed | 0xAF | XOR |
Down Right | 0xA0 | Address | 0x00 | 0x12 | Pan Speed | Tilt Speed | 0xAF | XOR |
Zoom In | 0xA0 | Address | 0x00 | 0x20 | 0x00 | 0x00 | 0xAF | XOR |
Zoom Out | 0xA0 | Address | 0x00 | 0x40 | 0x00 | 0x00 | 0xAF | XOR |
Focus Far | 0xA0 | Address | 0x00 | 0x80 | 0x00 | 0x00 | 0xAF | XOR |
Focus Near | 0xA0 | Address | 0x01 | 0x00 | 0x00 | 0x00 | 0xAF | XOR |
Set Preset | 0xA0 | Address | 0x00 | 0x03 | 0x00 | Preset ID | 0xAF | XOR |
Clear Preset | 0xA0 | Address | 0x00 | 0x05 | 0x00 | Preset ID | 0xAF | XOR |
Call Preset | 0xA0 | Address | 0x00 | 0x07 | 0x00 | Preset ID | 0xAF | XOR |
Query Pan Position | 0xA0 | Address | 0x00 | 0x51 | 0x00 | 0x00 | 0xAF | XOR |
Query Pan Position Response | 0xA0 | Address | 0x00 | 0x59 | Value High Byte | Value | ||
Low Byte | 0xAF | XOR | ||||||
Query Tilt Position | 0xA0 | Address | 0x00 | 0x53 | 0x00 | 0x00 | 0xAF | XOR |
Query Tilt Position Response | 0xA0 | Address | 0x00 | 0x5B | Value High Byte | |||
Value Low Byte | 0xAF | XOR | ||||||
Query Zoom Position | 0xA0 | Address | 0x00 | 0x55 | 0x00 | 0x00 | 0xAF | XOR |
Query Zoom Position Response | 0xA0 | Address | 0x00 | 0x5D | Value High Byte | |||
Value Low Byte | 0xAF | XOR |
OSD MENU
-
under working mode, press the menu button on the IR remote, to enter the OSD menu.
-
Use the navigate button to select the main menu. Once been selected, the main menu will change to grey color background, and the right side will show all parameters under this sub menu.
-
Press the right navigate button to enter sub menu, use up and down navigate button to select parameter.
-
To return to the previous menu level, use the navigation up and down keys to select the return line, and then press the navigation right key to return to the previous level.
-
Press the menu button again to exit the OSD menu.
-
OSD Menu List& Defaulted Setting
CAMERA SET| LANGUAGE| ENGLISH/CHINESE|
---|---|---|---
PROTOCOL| VISCA/PELCO-P/PELCO-D| VISCA
ADDRESS| VISCA:1~7 PELCO-P/D:0~255| 1
BAUD RATE| 2400/9600/115200| 9600
PARITY BIT| NONE|
RETURN| Return to previous menu|
VIDEO MODE| It will cause video freeze if switch video mode via OSD menu; Only recommend to change video mode via UVC control.
---|---
| RETURN| Return to previous menu|
FOCUS| FOCUS MODE| AUTO/MANU/PUSH| AUTO
---|---|---|---
SENSITIVITY| Focus Sensitivity setting: LOW/MID/HIGH| MID
FOCUS LIMIT| The target distance: 1.5M/2M/3M/6M/10M| 1.5M
D_ZOOM| Digital Zoom: OFF/ON| OFF
ZOOM SPEED| Set zoom speed level:0~7| 7
LENS INIT| Lens focus parameter frequency setting, choose EXE to start the lens focus reset|
OFF
DIS ZOOM RATIO| Display zoom value during zooming control| OFF
RETURN| Return to previous menu|
WB MODE| WB MODE| Set White Balance mode| ATW
---|---|---|---
B_GAIN| Set blue gain under manual mode| 52
R_GAIN| Set red gain under manual mode| 58
RETURN| Return to previous menu|
EXPOSURE| EXP MODE| AUTO、MANUAL、BRIGHT、SHUTTER、IRIS| AUTO
---|---|---|---
SHUT TIME| Set shutter speed: 1/8~1/10000 Only available under MANU or SHUT
mode| 1/100
IRIS| Set iris value: 0~13, only available under MANU or IRIS mode| 10
GAIN| Set gain value: 0~15, only available under MANU mode| 0
BRIGHT| Set bright value: 0~27 , only available under BRI. mode| 11
SLOW SHUT| Slow shutter set: OFF/ON| OFF
FLICK| 50HZ/60HZ/OFF| 50Hz
RETURN| Return to previous menu|
PICTURE| BRIGHTNESS| Set brightness value: 0~15| 6
---|---|---|---
SHARPNESS| Set sharpness value::0~15| 3
CONSTRAST| Set contrast value: 0~15| 7
SATURATION| Set saturation value: 0~15, the higher value, the stronger color|
9
| MIRROR| Left/right flip: ON/OFF| OFF
---|---|---|---
PIC FLIP| Up/down flip: ON/OFF| OFF
FREEZE| ON/OFF| OFF
DEFOG| Set image permeability| 2
RETURN| Return to previous menu|
IMAGE ENHANCE| 2D NR| ON/OFF| OFF
---|---|---|---
3D NR| OFF/AUTO/1~4| AUTO
D_WDR| Set dynamic level : OFF/1~6| 1
GAMMA| Set gamma: 0~4| 0
BACKLIGHT| ON/OFF| OFF
HIGHLIGHT| ON/OFF| OFF
RETURN| Return to previous menu|
MASK| MASK SWITCH| Privacy zone function: ON/OFF| OFF
---|---|---|---
COLOUR| Set mask zone color: WHITE/YELLOW/GRAY/GREEN/VIOLET/RED| WHITE
INDEX| Set mask zone number: 1~8| 1
INDEX SWITCH| Set index zone: ON/OFF| OFF
ROW START| Set current mask zone’s row start position| 0
ROW END| Set current mask zone’s row end position| 479
LINE START| Set current mask zone’s line start position| 0
LINE END| Set current mask zone’s line end position| 539
RETURN| Return to previous menu|
D/N MODE| D/N MODE| Set D/N mode: DAY/NIGHT/AUTO| DAY
---|---|---|---
DAY TO NIGHT| Set day to night brightness threshold value: 15~200| 48
NIGH TO DAY| Set night to day brightness threshold value: 5~190| 8
SWITCH DELAY| Set switch delay between different mode, to avoid repeat
switching under AUTO mode: 1~60s|
5
GAIN LIMIT| Gain limit under low light:2/4/6/8/11/16/32/64/128/256/320/511|
511
RETURN| Return to previous menu|
CAMERA INF.| IMAGE VER.| Image firmware version
---|---|---
IMAGE DATE| Image firmware release date: YY/MM/DD
CONTROL VER.| Control firmware version
CONTROL DATE| Control firmware release date: YY/MM/DD
BAUDRATE| Current baud rate value
PARITY BIT| Current control protocol parity bit value
RETURN| Return to previous menu
RESET| REEST to defaulted value (except the Language): ON/OFF
---|---
UVC CONTROL
- Only run the client software after the USB3.0 camera has completed self-configuration(the IR indicator in blue color and will not flash); otherwise may cause black video issue.
- Make sure the USB3.0 camera is recognized by the PC Device Manager.
- Make sure the interval of video format switching more than 1 seconds, otherwise black video maybe caused.
- Make sure the interval of control command sending from the server(via USB) to the camera no less than 250ms.
- Support standard UVC interface.
UVC Property | Corresponded VISCA Command |
---|---|
PU_BACKLIGHT_COMPENSATION_CONTROL | 8x 01 04 33 02 FF |
CY_FX_UVC_PU_BRIGHTNESS_CONTROL | 8x 01 04 A4 00 00 0p 0q FF |
CY_FX_UVC_PU_CONTRAST_CONTROL | 8x 01 04 A2 00 00 0p 0q FF |
CY_FX_UVC_PU_SATURATION_CONTROL | 8x 01 04 A1 00 00 0p 0q FF |
CY_FX_UVC_PU_SHARPNESS_CONTROL | 8x 01 04 42 00 00 0p 0q FF |
CY_FX_UVC_PU_GAMMA_CONTROL | 8x 01 04 5B 0p FF |
CY_FX_UVC_PU_WHITE_BALANCE_TEMPERATURE_CONTROL | 8x 01 04 35 0p FF |
CY_FX_UVC_PU_BACKLIGHT_COMPENSATION_CONTROL | 8x 01 04 33 0p FF |
CY_FX_UVC_PU_GAIN_CONTROL | 8x 01 04 49 00 00 0p 0q FF |
CY_FX_UVC_PU_POWER_LINE_FREQUENCY_CONTROL | 8x 01 04 AA 0p FF |
PU_GAIN_CONTROL | 8x 01 04 49 00 00 00 0p FF |
CT_ZOOM_ABSOLUTE_CONTROL | 8x 01 04 47 0p 0q 0r 0s FF |
CT_PANTILT_ABSOLUTE_CONTROL | 8x 01 06 02 VV WW 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z FF |
CT_PANTILT_RELATIVE_CONTROL | 8x 01 06 01 pp qq rr ss FF |
CT_ZOOM_RELATIVE_CONTROL | 8x 01 04 07 pp FF |
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>