MOEN UTS244201BG Brushed Gold Colinet Pressure Balanced Instructions
- June 3, 2024
- Moen
Table of Contents
MOEN UTS244201BG Brushed Gold Colinet Pressure Balanced
Dimension
Parts List
- A. Shower Arm Flange
- B. Shower Arm
- C. Showerhead
- D. Tub Spout
- E. *Tub Spout Escutcheon
- F. Installation sleeve with pressure balance puck and adapter
- F1. Install sleeve
- F2. Adapter
- F3. Inlet Seal (x2)
- F4. Bottom Seal
- F5. Outer Seal
- F6. Pressure balance puck
- G. Cartridge
- H. Adjustable Temperature Limit Stop
- I. Cartridge Nut
- J. Sleeve
- K.Mounting Plate
- L. Snap Ring
- M. Screws (x2)
- N. Escutcheon
- O. Handle
- P. Set Screw
- Q. Hex Wrench (3/32”)
- R. Grease Pack
- S. Hot & Cold Button
- T. Handle Cap
- U. Adapter
*Certain models
Installation Overview Steps
- Shower Arm Installation
- Showerhead Installation
- Tub Spout Installation
- Valve Body Preparation
- Cartridge Installation
- 8A 4 Port Valve
- 8B 3 Port Valve
Setting Temperature Limit
- Check Temperature
- 12 Adjust Temperature Limit
- 13-20 Trim Installation
Typical Installation Example
Optional Back-to-Back Installation
OPTION
- Wrap thread seal tape around shower arm (B) threads.
- Thread shower arm into connection in wall.
OPTION
- Slide Shower arm flange (A) onto shower arm (B).
- Wrap shower arm (B) with thread seal tape
OPTION
- Place Spout Escutcheon (E) onto Tub Spout (D) . Aligning notch as shown. (Separate escutcheon for some models).
OPTION
- Install tub spout (D) upside down onto pipe.
- Barely tighten tub spout set screw with 5/32” hex wrench.
OPTION
- Rotate tub spout (D) right side up.
- Secure spout by tightening tub spout set screw
Remove flush plug before applying grease
Apply grease to outer o-ring and inside of valve bore using grease pack (R
).
For 4 port control valves
- Align tab on Installation sleeve (F) facing up and place in line with valve. Push Adapter (F2) and pressure balance puck (F6) out of the installation sleeve (F1) into the valve until they bottom.
- Align 2 posts on cartridge (G) to mating feature in puck assembly and push cartridge into valve until it stops.
- Tighten cartridge nut (I) onto valve by turning it clockwise until hand tight, and then turn an additional ¼ turn with a wrench. Note: proper torque of nut to valve housing is 106-115 in-lbs (12-13Nm).
For 3 port control valves
- Push Adapter (F2) and pressure balance puck (F6) out of the installation sleeve (F1).
- Rotate Adapter (F2) 180 degrees and reattach to puck (F6).
- Insert parts F2 and F6 into installation sleeve F1 with the tab on the adapter up, aligning with the tab on the installation sleeve.
- Now follow steps in 8A to install the assembly into the valve
Use handle (O) to verify cartridge is closed. (Rotate clockwise to close.)
Turn on the hot and cold water supply and check for leaks.
Open handle to full hot to test hot water temperature. Close handle if desired water temperature has been met. Hot water temperature should not exceed 120°F.
Rotate the lever until the water is to the maximum desired temperature, not to exceed 120oF (49oC). Seasonal maintenance of the maximum outlet temperature may be required due to changes in groundwater temperature
Remove the handle (O).
Remove the adjustable temperature limit stop
Install the adjustable temperature limit stop (H) so it is in contact with the bottom of the stop on the left side of the cartridge (G), as shown in inset.
Slide sleeve (J) onto valve until it stops and orient markings downward.
Push mounting plate (K) onto sleeve until it bottoms on the wall and align holes to threaded holes in valve
- Orient the snap ring (L) to mounting plate (K) as shown with “FRONT” text facing forward and upright.
- Insert screws (M) (x2) through snap ring (L) and mounting plate (K) and secure to the valve until the mounting plate bottoms on the finished wall. Do not overtighten.
- Ensure the snap ring is centered on the sleeve for proper escutcheon placement, if off-center, loosen screws, reposition, and secure.
SOME MODELS
-
Apply a small amount of grease (R) to the backside of the button (S).
-
Push Hot/Cold button (S) into the escutcheon (N).
-
Orient slots in backside of escutcheon (N) with tabs on the top and bottom of snap ring (L).
-
Snap escutcheon (N) onto snap ring (L).
-
Ensure escutcheon (N) is centered on the sleeve (J) and markings are level.
For multi-piece handle designs
- Fully snap adapter (U) into the cartridge nut with arrows pointing up.
- Place handle (O) onto cartridge stem
Place the handle (O) onto cartridge stem
- Insert 3/32” hex wrench (Q) into set screw (P).
- Tighten set screw into handle (O)
SOME MODELS
- Apply a small amount of grease (R) to the backside of handle cap (T).
- Attach handle cap (T) to lever handle (O).
Installation complete.
Optional Back-to-Back Installation
For reversed valve installation (Hot plumbed to the right and cold plumbed to
the left side of the valve), rotate the pressure balancing puck (F6) and
cartridge (G) 180 degrees and reinstall into installation sleeve (F). Then
install into the valve, install the cartridge nut, and proceed to STEP 9
.
Moen Limited Lifetime Warranty
Moen products have been manufactured under the highest standards of quality
and workmanship. Moen warrants to the original consumer purchaser for as long
as the original consumer purchaser owns their home (the “Warranty Period” for
homeowners), that this product will be leak- and drip-free during normal use
and all parts and fi nishes of this product will be free from defects in
material and manufacturing workmanship. All other purchasers (including
purchasers for industrial, commercial and business use) are warranted for a
period of 5 years from the original date of purchase (the “Warranty Period”
for non-homeowners).
If this product should ever develop a leak or drip during the Warranty Period,
Moen will FREE OF CHARGE provide the parts necessary to put the product back
in good working condition and will replace FREE OF CHARGE any part or fi nish
that proves defective in material and manufac-turing workmanship, under normal
installation, use and service. Replacement parts may be obtained by calling
1-800-289-6636 (Canada
1-800-465-6130), or by writing to the
address shown. Proof of purchase (original sales receipt) from the original
consumer purchaser must accompany all warranty claims. Defects or damage
caused by the use of other than genuine Moen parts is not covered by this
warranty. This warranty is applicable only to products purchased after
December, 1995 and shall be effective from the date of purchase as shown on
purchaser’s receipt.
This warranty is extensive in that it covers replacement of all defective
parts and fi nishes. However, damage due to installation error, product abuse,
product misuse, or use of cleaners containing abrasives, alcohol or other
organic sol-vents, whether performed by a contractor, service company, or
yourself, are excluded from this warranty. Moen will not be responsible for
labor charges and/or damage incurred in installation, repair or replacement,
nor for any indirect, incidental or consequential damages, losses, injury or
costs of any nature relating to this product. Except as provided by law, this
warranty is in lieu of and excludes all other war-ranties, conditions and
guarantees, whether expressed or implied, statutory or otherwise, including
without restriction those of merchantability or of fi tness for use.
Some states, provinces and nations do not allow the exclu-sion or limitation
of incidental or consequential damages, so the above limitations or exclusions
may not apply to you. This warranty gives you specifi c legal rights and you
may also have other rights which vary from state to state, province to
province, nation to nation. Moen will advise you of the procedure to follow in
making warranty claims. Simply write to Moen Incorporated using the address
below. Explain the defect and include proof of purchase and your name,
address, area code and telephone number.
Moen Incorporated
25300 Al Moen Drive
North Olmsted, Ohio 44070-8022
U.S.A.
INS11041B – 07/21
©2021 Moen Incorporated
References
- MOEN | Bathroom & Kitchen Faucets
- Moen|Llaves para baño y cocina, cabezales, accesorios y más
- Register Your Product | Moen
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>