BORMANN BSM1305 Electrical Tool Instruction Manual
- September 19, 2024
- BORMANN
Table of Contents
BORMANN BSM1305 Electrical Tool
Technical Specifications
Technical data
Model:| BSM1305
Rated Voltage:| 230V/50 Hz
Input power:| 1300 W
Diameter:| 120×100 mm
No load speed:| 900-3200 rpm
Includes:
| ****
Polishing Brush
FAQs
Q: Can I use the BSM1305 for grinding tasks?
A: Yes, the BSM1305 can be used for grinding tasks with the appropriate disc/wheel attachments. Ensure you follow all safety precautions and guidelines provided in the manual.
Q: How do I adjust the speed on the BSM1305?
A: The speed can be adjusted using the speed controller located on the tool. Refer to the manual for detailed instructions on adjusting the speed based on your application needs.
SAFETY INSTRUCTIONS
Warning : Read the manual carefully before use. Failure to follow the warnings and instructions may result in tool damage, physical injury and/or damage to property. Store the manual in a safe place for future reference.
Symbols
Specific Safety Instructions
This electrical tool will be used exclusively following the prescriptions and according to its purpose. Exclusively use accessories specifically approved by the manufacturer for their use with this electrical tool. The rotation speed of the tool used will be the value indicated on the electronic equipment at the very least. The external dimensions and the thickness of the tool used will correspond to the measurements indicated on the electronic equipment. The grinding drum and shroud, or other types of accessory, will fit correctly onto the corresponding spindle of the electrical tool. Do not use damaged accessories. Check the application tool before each use in order to determine if it shows detachments or fissures and, in the case of grinding plates, the presence of fissures or excess wear. If the electric tool or the application tool falls to the floor, check if they are damaged or directly use an undamaged tool. Once the application tool has been checked and is in position, keep yourself and others outside the rotation plane, leaving the equipment running for one minute at maximum speed. Use personal protection equipment. Use integral face protection and eye protection (protective glasses) in accordance with the regulations. If necessary, use a dust mask, ear protection (headphones), protective gloves, special footwear, or an apron that keeps small particles caused by grinding away from your body. Ensure other persons nearby are outside your work area. Anyone accessing the work area must be provided the adequate protection equipment. Do not leave the electrical tool running while moving it from one place to another. Regularly clean the ventilation slits of the electrical tool. Do not use the electrical tool near flammable substances. Do not use application tools requiring liquid coolants. Backward movement and corresponding safety measures. Backlash is a sudden reaction to a jammed or blocked processing tool, such as a grinding plate, a rotating brush, etc. Jamming or blocking will cause the rotating processing tool to stop suddenly. This causes an uncontrolled acceleration of the electrical equipment at the point it becomes blocked, in the rotation sense opposite to that of the tool. A backlash is the consequence of an improper or inadequate use of the electrical tool. It may be avoided by means of the preventive measures, as described below. Hold the electrical tool firmly and place your bodyand arms in a position allowing you to offset the backlashes. Should it exist, always use the additional handle in order to have greater control in the case of backlashes or reactions during start-up. The operator can control the backlash or reaction forces by using the appropriate precautionary measures. Never move your hand close to the application tool while it is rotating. The tool can move onto your hand in the case of a backlash. Avoid your body from entering the area in which the electronic equipment eventually moves during backlashes. A backlash pushes the electrical tool in the opposite direction to the movement of the grinding disc at the point where it becomes blocked.
Work taking particular care near corners, sharp tubes, etc
Avoid the tool bouncing off the piece being processed and becoming jammed. The rotating application tool tends to get jammed on comers, sharp edges or when bouncing off the piece being processed. This leads to a loss of control or a backlash.
Special safety indications for roughing
Exclusively use approved roughing elements for this electrical tool with its corresponding protection cover. Roughing elements not approved for this electrical tool cannot be covered adequately therefore not being safe.The protection cover will be firmly assembled on the electrical tool and adjusted in such a way maximum safety is achieved. That is to say, the smallest portion of the uncovered grinding agent will be facing the operator. The protection cover has the task of protecting the operator from bit becoming detached and from any eventual contact with the grinding element. The grinding elements will be used exclusively for their designated uses.
Other safety indications
Always hold the electrical tool with both hands on the corresponding surfaces (motor casing and handle). Hold smaller pieces to be processed in order to avoid their involuntary displacement. The power supply network voltage and the voltage indications on the characteristics plate must coincide.
- The manufacturer reserves the right to make minor changes to product design and technical specifications without prior notice unless these changes significantly affect the performance and safety of the products. The parts described/illustrated in the pages of the manual that you hold in your hands may also concern other models of the manufacturer’s product line with similar features and may not be included in the product you just acquired.
- To ensure the safety and reliability of the product and the warranty validity, all repair, inspection or replacement work, including maintenance and special adjustments, must only be carried out by technicians of the authorized service department of the manufacturer.
- Always use the product with the supplied equipment. Operation of the product with non-provided equipment may cause malfunctions or even serious injury or death. The manufacturer and the importer shall not be liable for injuries and damages resulting from the use of non-conforming equipment.
STARTUP
Description
- Switch
- Brush cover
- Speed controller
- Ventilation grilles
- Handle
- Protective housing
- Disc/Drum/wheel (optional)
- Cable
- Gear head
- Spindle lock button
OPERATION
Start-up
Disconnect the power supply plug before performing any work on the electrical equipment.
Prior to start-up
Unpack the electrical tool check the volume handed over is complete and determine if any damage occurred during its transport.
- Press the switch, keeping it pressed down.
- If you want to stop the tool, release the switch.
Rotation speed controller
- To adjust the working speed, turn up or turn down the speed controller.
Tool Change
Wheel Change
- Disconnect the plug from the power supply.
- Press the spindle locking button and keep it pressed down.
- Loosen the screws with a wrench and remove the drum.
- Replace the drum with the wheel that you need, screw back the nut tightly. Ensure that it is well-assembled before being plugged.
Adjustment Operation
Protection cover adjustment
The burnishing machine will always be used with the protection cover in place.
- Loosen the cover adjustment screw
- Adjust the protection cover in a position that is appropriate for the task to be performed and in the corresponding work position
- Adjust the screw once more.
General Use Instructions
Processing of flat surfaces
- Hold the electrical tool with both hands.
- For a decorative finishing of the surface: Carefully base the electrical tool on the surface to be processed, performing a straight-line movement forward and then back.
MAINTENANCE AND CLEANING INSTRUCTIONS
Disconnect the power supply plug before performing any work on the electrical equipment.
Cleaning
Conducting dust may be deposited inside the casing when processing metals. This may have an influence on the protection insulation! Start the machine using a differential circuit breaker (maximum operating current 30 mA). Regularly clean the equipment and the ventilation slits. Cleaning frequency will depend on the material and the intensity of use. Periodically clean the lower part of the casing and the motor with dry compressed air.
ENVIRONMENTAL DISPOSAL
In order to avoid damages on transportation, the tool has to be delivered in solid packaging. Packaging as well as the unit and accessories are made of recyclable materials and can be disposed of accordingly. The tool’s plastic components are marked according to their material, which makes it possible to remove environmentally friendly and differentiated because of available collection facilities.
Only for EU countries
Do not dispose of electric tools together with household waste material! In observance of European Directive 2002/96/EC on waste electrical and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.
WARRAΝΤΥ
The power tools have been manufactured according to strict standards, set by our company, which are aligned with the respective European quality standards. The power tools of our company are provided with a warranty period of 24 months for non-professional use, 12 months for professional use, and 12 months for chargers and batteries. The warranty is valid from the date of purchase of the product. Proof of the warranty right is the purchase document of the tool (retail receipt or invoice). Under no circumstances shall the company cover the relevant cost of spare parts and respective required working hours unless a copy of the purchase document is presented. In case the repair has to be done by our service department the cost of transportation (to and from) is entirely borne by the sender (client). The tools must be sent for repair to the company or to an authorized workshop in the appropriate way and means of transport.
WARRANTY EXEMPTIONS AND RESTRICTIONS
- Spare parts that wear out naturally as a consequence of being used (brushes, cables, switches, chargers, chokes, etc.).
- Tools damaged as a result of non-compliance with the instructions of the manufacturer.
- Tools poorly maintained.
- Use of improper lubricants or accessories.
- Tools are given to third entities free of charge.
- Damage due to an electrical connection at a voltage other than that indicated on the appliance plate.
- Connection to a non-earthed power supply.
- Change in current voltage.
- Damage resulting from the use of salty water (e.g., washing machines, pumps).
- Damage or malfunction resulting from improper cleaning procedure of the tool.
- Contact of the tool with chemicals, or damage as a result of moisture or corrosion.
- Tools that have been modified or opened by unauthorized personnel.
- Tools used for rent.
The warranty covers only the free-of-charge replacement of the component that presents a manufacturing defect or material failure. In case of a lack of a specific spare part, the company reserves the right to replace the tool with another corresponding model. After all warranty procedures have been concluded, the warranty period of the tool shall not be extended or renewed. Replacement of a spare part with a repair charge is covered by a 1-year warranty of good operation, subject to compliance with the warranty terms. The spare parts or tools thatare replaced remain in the possession of our company. Requirements, other than those mentioned in this warranty form, regarding power tools repair or damage thereof, do not apply. Greek law and relative regulations apply to this warranty.
The instructions manual is also available in digital format on our website www.nikolaoutools.com. Find it by entering the product code in the Search field.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>