ZEALAND 1500x1500x600 Workstation Coronet Beech Instruction Manual
- June 4, 2024
- ZEALAND
Table of Contents
ZEALAND 1500x1500x600 Workstation Coronet Beech
OVERVIEW
TOOLS REQUIRED
POZIDRIVE SCREW DRIVER
10MM SPANNER
WORKSTATION COMPONENTS| QUANTITY
---|---
|
MAIN TOP| 1
TOP ADD ON| 1
LEFT LEG| 1
RIGHT LEG| 1
CENTRE LEG| 1
LEFT HAND BRACE| 1
RIGHT HAND BRACE| 1
|
HARDWARE| QUANTITY
( PACKAGED WITH LEGS )|
CAMS (PRE FITTED IN FACTORY )| 20
CAM BOLTS| 20
SCREWS 1 1/4″| 2
BENCH TOP CONNECTORS| 3
-
STEP 1
PLACE TOP PANELS FACE DOWN ON A CLEAN SURFACE SUCH AS CARPET ENSURING THERE IS NO DIRT OR GRIT THAT MAY CAUSE SCRATCHES. -
STEP 2
LINE UP TOPS AND INSERT THE 3 BENCH TOP CONNECTORS, TIGHTEN CONNECTERS ENSURING THE TOPS ARE FLUSH ( ADJUST WHEN UPRIGHT IF REQUIRED ) IMPORTANT NOTE:
PLEASE ENSURE THAT THE JOIN IS COMPLETELY FLUSH ON THE FRONT FACE BEFORE TIGHTENING FULLY AS ATTEMPTING TO ADJUST THIS ONCE TIGHTENED COULD CAUSE DAMAGE TO THE MELAMINE FRONT FACE. -
STEP 3
USING A POZIDRIVE SCREWDRIVER INSERT 14 CAM BOLTS INTO THE 5MM DRILLED HOLES IN THE TOPS -
STEP 4
USING A POZIDRIVE SCREWDRIVER INSERT 2 CAM BOLTS INTO THE 5MM DRILLED HOLES IN THE LEFT HAND LEG -
STEP 5
USING A POZIDRIVE SCREWDRIVER INSERT 2 CAM BOLTS INTO THE 5MM DRILLED HOLES IN THE RIGHT HAND LEG -
STEP 6
USING A POZIDRIVE SCREWDRIVER INSERT 2 CAM BOLTS INTO THE 5MM DRILLED HOLES IN THE MIDDLE LEG -
STEP 7
PLACE THE LEFT HAND LEG PANEL AND CAMS ON TO THE TOP CAM BOLTS AND USING A POZIDRIVE SCREWDRIVER TIGHTEN CAMS UNTIL FULLY TIGHT -
STEP 8
PLACE THE MIDDLE LEG PANEL AND CAMS ON TO THE TOP CAM BOLTS AND USING A POZIDRIVE SCREWDRIVER TIGHTEN CAMS UNTIL FULLY TIGHT -
STEP 9
PLACE THE LEFT HAND LEG PANEL AND CAMS ON TO THE TOP AND LEG PANEL CAM BOLTS AND USING A POZIDRIVE SCREWDRIVER TIGHTEN CAMS UNTIL FULLY TIGHT -
STEP 10
PLACE THE RIGHT HAND LEG PANEL AND CAMS ON TO THE TOP CAM BOLTS AND USING A POZIDRIVE SCREWDRIVER TIGHTEN CAMS UNTIL FULLY TIGHT -
STEP 11
PLACE THE RIGHT HAND BRACE PANEL AND CAMS ON TO THE TOP AND LEG PANEL CAM BOLTS AND USING A POZIDRIVE SCREWDRIVER TIGHTEN CAMS UNTIL FULLY TIGHT -
STEP 12
USING A POZIDRIVE SCREWDRIVER INSERT 2 SCREWS THROUGH THE PREDRILLED HOLES AND FASTEN SECURELY IN TO THE MIDDLE LEG UNTIL FLUSH -
STEP 12
BEFORE TURNING THE WORKSTATION THE CORRECT WAY UP, PLEASE ENSURE ALL CAMS AND BENCH TOP CONNECTORS ARE FULLY TIGHTENED -
STEP 13
USING A 2ND PERSON TO HELP LIFT, TURN THE WORKSTATION OVER AND PLACE IN DESIRED POSITION, DO NOT DRAG ASSEMBLED WORKSTATION
YOU ARE NOW READY TO ENJOY YOUR WORKSTATION. THANK YOU, WE APPRECIATE YOU SUPPORTING OUR NEW ZEALAND MADE PRODUCT
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>