FETCO GRS-1200 Single Hopper Commercial Coffee Grinder

OVERVIEW

• GRS-1201 Commercial Coffee Grinder
• GRS-1202 Commercial Coffee Grinder

*NM denotes Spanish language labeling and user guide

Features

• FETCO slicing type grinding burrs
• Self-adjusting brew basket holder
• Fully automatic, with digital timer control
• Front accessible & Service Friendly
• Motor overload protection
• Export versions: 200-240Vac; 50Hz motor

Contact Information
FETCO®
Food Equipment Technologies Company 600 Rose Road

fetco.com

Lake Zurich • IL • 60047-1560 • USA
© 2018-2024 Food Equipment Technologies Company

• Internet: www.fetco.com
• Phone: 800-338-2699 (US & Canada) 847-719-3000
• Fax: 847-719-3001
• Email: sales@fetco.com
• techsupport@fetco.com

Specifications

• Hopper Capacity: GRS-1201: 15 lbs. / 6.8 kg.
• GRS-1202: 5 lbs. / 2.3 kg. each
• Timer Range: 5-60 sec .
• *Grind Rate:** 16oz. / 450g per minute
• Grind Setting Default: Medium
• Brew Basket Size: 7” to 9” diameter

Electrical

• North America: 120 VAC, 60 Hz single phase 475 Watts
• Motor: 5.7 amps, 370 Watts, 0.67 HP
• The grinder is IPX-1 Motor is IP 44 NEMA 5-15P plug/cord
• Export: 230 VAC, 50 Hz single phase 250 Watts
• Motor: 3.8 amps, 370 Watts, 0.74 HP IP 44 (motor only) Grinder is IPX-1 Motor is IP 44
• Plug/cord configuration set per country electrical-see below

Sound Rating
Normal 72-75db Momentary pulse for GRS-1202 hopper actuator: 85db

Grind rate is determined at medium grind with medium size, average to dark roast beans

Dimensions & Utility Connections

Model| Minimum height for top opening| Height| Width| Depth| Weight| Shipping Weight| Shipping Dimensions
---|---|---|---|---|---|---|---
GRS-1201| 40 1/8 (+) in.

1019(+) mm

| 28 3/4 in. 729mm| 9 1/8in. 233mm| 16 3/8in.

416 mm

| 51lb 23kg| 67lb 31kg| 31”HX12WX19D

788mmHX305mmWx483mmD

GRS-1202| 40 1/8 (+) in.

1019(+) mm

| 28 3/4 in. 729mm| 9 1/8in. 233mm| 16 3/8in.

416 mm

| 52lb 24kg| 67lb 31kg| 31”HX12WX19D

788mmHX305mmWx483mmD

Electrical plug/cord configuration

Starting the Grind

1. Place whole coffee beans in a hopper
2. Prepare a brew basket with the correct size filter.
3. Slide the prepared brew basket completely into the holder
4. Turn the power switch “ON”
5. Select a batch & press the corresponding BATCH button in to start
6. The STOP button will illuminate, Batch Selector button will illuminate
7. Countdown time will display. Default time setting is 20;13;7 seconds (6,4,2.5 oz)
8. The selected BATCH button will slowly pulsate to indicate grinding is in progress.
9. All other BATCH buttons will remain unlit during the grind cycle.
10. When the grind cycle is finished, the STOP button will extinguish ..
11. Remove the filled brew basket and proceed to brew

GRS-1202 only-Solenoid Delay

1. Closes hopper guillotine and leaves motor running to empty grind chamber (If activated)
2. Factory default is ACTIVATED with 20 SECOND delay.
   The GRS-1202 solenoid delay feature prevents mixing the coffee types in the two hoppers (such as regular in one hopper and decaffeinated in the other)

Enter Programming
There are 6 menu groups-A-F plus EXIT (G). (“E” level has not been added as of January 2024) See the following pages for the batch parameter definitions and all settings for the grinder

Layout for Programing Menu GRS-1220 series

Factory default settings for grinder outputs

Notes
A1:00| Grind Enabled Left 1 (large)| (Screen does not display)| 5-60 sec| 1sec| Always Enabled
A1.20| Grind Time| 20sec (+20sec-see B1)

6oz or 170grams

| 5-60 sec| 1sec| Adjustable 5-60 sec or 2oz/50g to 16oz/450g
A2.00| Grind Enabled Left-1 (large)| YES| YES/NO| On,Off| Can be turned Off/On
A2.20| Grind Time| 13sec (+20sec-see B1)

(4oz or 114grams)

| 5-60 sec| 1sec| Adjustable 5-60 sec or 2oz/50g to 16oz/450g
A3.00| Grind Enabled Left -2 (medium)| YES| YES/NO| On,Off| Can be turned Off/On
A3.20| Grind Time| 7sec. (+20sec-see B1)

(2.5oz or 70grams)

| 5-60 sec| 1sec| Adjustable 5-60 sec or 2oz/50g to 16oz/450g
A4.00

(GRS-1202 only)

| Grind Enabled Right-1 (large)| (Screen does not display)| 5-60 sec| 1sec| Always Enabled

A4.20

|

Grind Time

| 20sec (+20sec-see B1)

6oz or 170grams

|

5-60 sec

|

1sec

| Always Enabled Adjustable 5-60 sec or 2oz/50g to 16oz/450g
A5.00

(GRS-1202 only)

| Grind Enabled Right-2 (medium)| YES| YES/NO| On,Off| Can be turned Off/On
A5.20| Grind Time| 13sec (+20sec-see B1)

(4oz or 114grams)

| 5-60 sec| 1sec| Adjustable 5-60 sec or 2oz/50g to 16oz/450g
A6.00

(GRS-1202 only)

| Grind Enabled Right-3 (small)| YES| YES/NO| On,Off| Can be turned Off/On
A6.20| Grind Time| 7sec. (+20sec-see B1)

(2.5oz or 70grams)

| 5-60 sec| 1sec| Adjustable 5-60 sec or 2oz/50g to 16oz/450g
A90| Copy Batch| | Select batch 1-6| |
A92| Paste To| | Select batch 1-6| |
Batch Size| Typical Coffee Dosage| Timer setting
---|---|---
Ounces| Grams
½ Gallon| 2 – 4 oz.| 57 – 113 grams| 6.7 – 13.3 sec.
2.5 – 3.0 Liters| 2 – 4.5 oz.| 57 – 128 grams| 6.7 – 15 sec.
1 Gallon| 4 – 8 oz.| 113 – 227 grams| 13.3 – 27 sec.
1.5 Gallons| 6 – 12 oz.| 170 – 340 grams| 20 – 40 sec.
2 Gallons| 8 – 16 oz.| 227 – 454 grams| 27 – 53 sec.
3 Gallons| 12 – 24 oz.| 340 – 680 grams| 40 – 80 sec.
6 Gallons| 39 – 51 oz.| 1.1 – 1.44 kg.| 130 -170 sec.

Weights are approximate based on medium grind with medium size, average to dark roast Arabica beans. Expect more variation when the timer is ten seconds or less

Notes

B1

|

Motor Delay*

|

20 seconds

|

0-60 seconds

|

1 sec.

| GRS-1202 only. Shuts hopper/grinder is ON to

empty grind chamber

B2| Solenoid Delay| 1 second| 0-2 seconds| 1 sec.| Timer to pause hopper opening from motor start
B3| Customer Name| OFF| ON/OFF| | Activates B4 name
B4| Customer Name| Enter letters| | |
B5| Demo Mode| OFF| ON/OFF| | Operate keys alone
*GRS-1202 dual hopper only. Delay starts after timed grind is completed and shuts off the coffee hopper while the motor runs to completely empty the grind chamber. This prevents cross contamination from the contents of the two hoppers
C Service Inputs| | Peripheral communication and keypad
---|---|---
POSITION| Program Items| Factory set Default| Programming Range| Increments| Notes
C1| USB Drive| OFF| ON/OFF| | Shows active USB
C2| Keyboard Test| | | | Reboot when complete
D Service Outputs| | Test motor, solenoids and set screen & button brightness
---|---|---
POSITION| Program Items| Factory set Default| Programming Range| Increments| Notes
D1| Motor Output| OFF| OFF/ON| | Shows motor ON/OFF

D2

| Lt Solenoid

Left solenoid GRS-1202 only

|

OFF

| OFF/ON| | Activate hopper solenoid and hopper solenoid SSR

D3

| Rt Solenoid

Right solenoid GRS-1202 only

|

OFF

| OFF/ON| | Activate hopper solenoid and hopper solenoid SSR
D4| LCD Brightness| 90%| 20% to 100%| 5%| This is DISPLAY brightness
D5| LED Brightness| 60%| 20% to 100%| 5%| This is BUTTON brightness
F Service Menu| | Set Model Type, Software & View Codes and Settings
---|---|---
POSITION| Program Items| Factory set Default| Programming Range| Increments| Notes
F1| Firmware Version| 4.0240118a| January 2024| | Software to program and operate all grinder functions

F2

|

Bootloader Version

|

2.2.220811

|

January 2024

| | Embedded BIOS to operate and update the firmware

(BIOS basic input/output system)

F3| Select Model| Sold as GRS-1201 or GRS-1202| GRS-1201/GRS-1202| | Factory set

Reset if board is serviced

F8| Backup to USB| NO| Follow prompts| | Save programmed settings
F9| Restore From USB| NO| Applies settings from USB| | Insert USB Will need reboot
F10| Restore Defaults| NO| NO/YES| | Restores settings to factory
F11| Error Log| Lists error codes| 1: ;2: ;3: (1= newest)| Newest first| See chart for error code definitions
F12| Erase Error Log| NO| | Toggle +/- YES or NO| FACTORY USE ONLY. DO NOT RESET
F13| Service Phone #| 800-338-2699| | | Factory technical support

H Save & Exit Saving changes and exiting PROGRAMMING
The grinder will save changes only from the “H” menu. DO NOT reboot grinder or toggle ON/OFF-Exit as below.

To exit programming & how to save control setting changes

• HOW TO SAVE CHANGES AND EXIT-The grinder is in PROGRAMMING mode.
• A convenient way to access the steps is to remember to scroll to EXIT→YES and scroll to SAVE →YES Programming changes must be saved as shown below. Do not turn the grinder off programming will be lost.

Exit Programming & Save
Control Setting Changes

NOTE : User-programmed settings will be erased and overwritten to factory default settings by the following three programming changes

• When setting the grinder model →The software sets equipment to grinder defaults: (SETTING F3)
• When loading from USB (Reprograms settings): (SETTING F9)
• When restoring defaults (Reloads to defaults ): (SETTING E10)

Grinder service and maintenance

INSTALLATION, ADJUSTMENT AND SERVICE……….
THESE SECTIONS ARE FOR PROFESSIONAL USE ONLY!

The danger of fire or electric shock-do, not open panels. No user-serviceable parts inside.
All adjustments and services to be performed by authorized professional personnel.

Grind Adjustment

Empty the hopper(s).

• GRS 12001: Scoop out as many beans as possible. Lift the window up and sweep out the remaining beans.
• GRS-1202: Remove both hoppers and dump the beans out. Place both hoppers back in grinder.

1. Press one of the large portion switches. This will clear the grinding chamber of any remaining beans.
2. Remove the front cover. There are 2 screws in front and 2 underneath near the coffee outlet.
3. Using a 7/8” or 22 mm wrench turn the retaining nut counterclockwise at least one turn.
4. Using a 3/8” to 1/2” standard screwdriver turn the adjustment screw clockwise for a finer grind, counterclockwise for a coarser grind. Note: Do not exceed more than a 1/4 turn in either direction.
5. Turn retaining nut clockwise, locking adjustment screw in place.
6. Grind a small amount of coffee beans to test the setting. Repeat the above steps if necessary.

To reset the grind setting to the factory default:

• Follow steps 1 – 4 of the grind adjustment procedure.
• Turn the adjustment screw clockwise until the grinding discs touch, then back off slightly.
• Using a marker, mark the twelve o’clock position of the adjustment screw.
• Turn the screw counterclockwise to just past the four o’clock position.
• Turn retaining nut clockwise locking adjustment screw in place.
• Test by grinding a small batch.

Note : It may be necessary to adjust the grind time to compensate for the new grind setting.
A finer grind will produce less ground coffee per minute and a coarser grind will produce more ground coffee per minute

Parts Diagrams

GRINDER ASSEMBLY, GRS-1202 BILL OF MATERIALS DRAWING NO.1101.00612.00

GRINDER ASSEMBLY, GRS-1202 BILL OF MATERIALS DRAWING NO.1101.00612.00

| QTY| PART NO| DESCRIPTION

1| 1| 1111.00117.00| BODY, WELDMET, GRS-1202
2| 4| 1029.00009.00| FASTENER, PUSH IN, 9/32″ HD. DIA X .165″ LG,
3| 4| 1073.00006.00| FOOT, GRINDER
4| 8| 1083.00019.00| WASHER, #10 SCREW SIZE, SPRING LOCK
5| 4| 1082.00031.00| SCREW, #10-32 X 5/8″, PAN HD PHIL, MACHINE
6| 1| 1083.00011.00| WASHER, #8 SCREW SIZE, INTERNAL TOOTH LOCK
7| 1| 1084.00006.00| NUT, 8-32 18-8 HEX MACHINE SCREW
8| 1| 1021.00005.00| ROD, VIBRATION DAMPENING, GR-2
9| 1| 1082.00130.00| SCREW, TRUSS, HD, SELF TAPPING #8 X .500 SS
10| 2| 1102.00034.00| SOLENOID ASSEMBLY, 120VAC, GR-2
11| 4| 1083.00026.00| WASHER, #10 SCREW SIZE, FLAT
12| 4| 1084.00014.00| NUT, HEX, #10-32, MACHINE SCREW
13| 1| 1067.00001.00| CAPACITOR, 120VAC VERSION, 40uF, 450VAC, 50-60Hz
| | 67005| CAPACITOR, 230VAC VERSION, 18uF, 450VAC, 50Hz (EXPORT VERSION ONLY)
| | 1067.00005.00| CAPACITOR, 120VAC VERSION, 80uF, 450VAC, 50-60Hz (JAPAN VERS.-2 REQD.)
14| 1| 1083.00025.00| WASHER, M8 SCREW SIZE, SPRING LOCK
15| 1| 1084.00018.00| NUT, HEX, M8 SCREW SIZE
16| 1| 1065.00003.00| CONNECTOR, POWER INLET, 15A, 250VAC
17| 1| 1058.00024.00| SWITCH, POWER, DOUBLE POLE, 16A, 125/250 VAC
18| 4| 1081.00006.00| SPACER, 6MM OD x 3.2MM ID x 5MM LG, Z/P
19| 1| 1052.00001.00| POWER SUPPLY, 90-264VAC/24VDC, 1.8A
20| 4| 1029.00012.00| SPACER, .25″ HEX X 1″ LG, FEM #4-40 THREAD
21| 2| 1052.00056.00| RELAY, SOLID STATE, PANEL MTG. EL240A30-24P
22| 6| 1081.00042.00| STANDOFF, 1/4″ HEX
23| 1| 1052.00033.00| RELAY, SOLID STATE, 50A/480VAC, W/BUILD IN VARISTOR
24| 2| 1023.00044.00| MANIFOLD, GR-2
25| 4| 1083.00010.00| WASHER, #12 SCREW W/NEOPRENE-BONDED SEAL
26| 4| 1082.00017.00| SCREW, TRUSS HD. PHIL. MACHINE, # 6-32 X 1/2 LG.
27| 2| 1102.00033.002| HOPPER, ASSEMBLY, GR-2 [ORDER AS A066]
28| 1| 1102.00038.00| GRINDING MOTOR AND PLATE ASSY, 120V/60Hz
28| 1| 1102.00185.00| COMPLETE GRINDING MOTOR ASSEMBLY, 230VAC/50Hz
29| 2| 1083.00022.00| WASHER, 3/8″ SCREW SIZE, FLAT
30| 2| 1083.00020.00| WASHER, SPRING LOCK, 3/8 SCREW, 18-8 SS
31| 2| 1082.00032.00| SCREW, 3/8″-16 X 3/4″ LG, HEX HEAD CAP
32| 1| 1058.00055.00| USB CONNECTOR
33| 1| 1401.00203.00| WIRING DIAGRAM, GRS-1200, L-N-PE, UNIVERSAL
34| 1| 1402.00125.00| HARNESS, GRS-1200, UNIVERSAL
35| 1| 1402.00125.01| HARNESS, GRS-1202, ADDITIONAL
36| 1| 1041.00035.00| LABEL, EXACTOR PLUS GRINDING SYSTEM
37| 1| 1112.00023.00| BASE COVER WELDMENT, GR/GRF
38| 10| 1082.00033.00| SCREW, PAN HD PHIL. MACH., W/DUAL ACT WASHER,

6-32×3/8LG.

39| 1| 1001.00035.00| COVER, REAR, GR-2
| | |
40| 1| 1102.00534.00| ASSEMBLY, FRONT PANEL, GRS-1202
41| 1| 1102.00533.00| COVER, GRS-1200 SERVICE ASSEMBLY, W/O RAILS
42| 1| 1023.00041.00| HOLDER, BREW BASKET, GR-1/2
43| 1| 1046.00035.00| LABEL, WARNING “TO REDUCE RISK OF ELECTRIC SHOCK OR FIRE”
| 1| 1063.00003.00| CORD, POWER, AMERICAN, 120VAC, 13A, 6FT LG.
| 1| 1063.00027.00| CORD, ENGLAND, 6.5FT
| 1| 1063.00026.00| CORD, AUSTRALIAN, 6.5FT
| 1| 1063.00025.00| CORD, EUROPEAN, 6.5FT
| 1| 1063.00028.00| CORD, SOUTH AFRICA , 6.5FT

GRINDER ASSEMBLY, GRS-1201 BILL OF MATERIALS DRAWING NO.1101.00613.00

| QTY| PART NO| DESCRIPTION

1| 1| 1111.00118.00| WELDMENT BODY, GRINDER; COMPLETE, GRS-1201,120VAC
2| 4| 1073.00006.00| FOOT, GRINDER
3| 4| 1083.00019.00| WASHER, #10 SCREW SIZE, SPRING LOCK
4| 4| 1082.00031.00| SCREW, #10-32 X 5/8″, PAN HD PHIL, MACHINE
5| 1| 1083.00011.00| WASHER, #8 SCREW SIZE, INTERNAL TOOTH LOCK
6| 1| 1084.00006.00| NUT, 8-32 18-8 HEX MACHINE SCREW
7| 1| 1021.00005.00| ROD, VIBRATION DAMPENING, GR-2
8| 1| 1082.00130.00| SCREW, TRUSS, HD, SELF TAPPING #8 X .500 SS
9| 1| 1028.00001.00| WINDOW, GR-1
10| 1| 1067.00001.00| CAPACITOR, 120VAC VERSION, 40uF, 450VAC, 50-60Hz
| | 67005| CAPACITOR, 230VAC VERSION, 18uF, 450VAC, 50Hz (EXPORT VERSION ONLY)
| | 1067.00005.00| CAPACITOR, 120VAC VERSION, 80uF, 450VAC, 50-60Hz (JAPAN VERS.-2 REQD.)
11| 1| 1083.00025.00| WASHER, M8 SCREW SIZE, SPRING LOCK
12| 1| 1084.00018.00| NUT, HEX, M8 SCREW SIZE
13| 1| 1058.00024.00| SWITCH, POWER, DOUBLE POLE, 16A, 125/250 VAC
14| 8| 1081.00006.00| SPACER, 6MM OD x 3.2MM ID x 5MM LG, Z/P
15| 1| 1058.00055.00| USB CONNECTOR
16| 1| 1402.00125.00| HARNESS, GRS-1200, UNIVERSAL
17| 1| 1052.00001.00| POWER SUPPLY, 90-264VAC/24VDC, 1.8A
18| 4| 1029.00012.00| SPACER, .25″ HEX X 1″ LG, FEM #4-40 THREAD
19| 1| 1052.00033.00| RELAY, SOLID STATE, 50A/480VAC, W/BUILD IN VARISTOR
20| 2| 1081.00042.00| STANDOFF, 1/4″ HEX
21| 1| 1102.00038.00| GRINDING MOTOR AND PLATE ASSY, 120V/60Hz
22| 2| 1083.00022.00| WASHER, 3/8″ SCREW SIZE, FLAT
23| 2| 1083.00020.00| WASHER, SPRING LOCK, 3/8 SCREW, 18-8 SS
24| 2| 1082.00032.00| SCREW, 3/8″-16 X 3/4″ LG, HEX HEAD CAP
25| 1| 1023.00148.00| FUNNEL, HOPPER, GR-1
26| 2| 1083.00010.00| WASHER, #12 SCREW W/NEOPRENE-BONDED SEAL
27| 2| 1082.00023.00| SCREW, #8-32 X 3/8 TRUSS HD PHIL., MACHINE
28| 1| 1001.00020.00| COVER, REAR, GR-1/GRF-2
29| 1| 1401.00203.00| WIRING DIAGRAM, GRS-1200, L-N-PE, UNIVERSAL
30| 8| 1082.00033.00| SCREW, PAN HD PHIL. MACH., W/DUAL ACT WASHER,

6-32×3/8LG.

31| 1| 1112.00023.00| BASE COVER WELDMENT, GR/GRF
| | |
32| 1| 1102.00536.00| ASSEMBLY, FRONT PANEL, GRS-1201
33| 1| 1102.00533.00| COVER, GRS-1200 SERVICE ASSEMBLY, W/O RAILS
34| 1| 1023.00041.00| HOLDER, BREW BASKET, GR-1/2
35| 1| 1046.00035.00| LABEL, WARNING “TO REDUCE RISK OF ELECTRIC SHOCK OR FIRE”
36| 1| 1041.00035.00| LABEL, EXACTOR PLUS GRINDING SYSTEM
37| 1| 1065.00003.00| CONNECTOR, POWER INLET, 15A, 250VAC
38| 1| 1084.00051.00| NUT, HEX LOCKWASHER, #8-32, 18-8 ST. STL.
| 1| 1063.00003.00| CORD, POWER, AMERICAN, 120VAC, 13A, 6FT LG.
| 1| 1063.00027.00| CORD, ENGLAND, 6.5FT
| 1| 1063.00026.00| CORD, AUSTRALIAN, 6.5FT
| 1| 1063.00025.00| CORD, EUROPEAN, 6.5FT
| 1| 1063.00028.00| CORD, SOUTH AFRICA , 6.5FT

ONLY
2| 1| 1112.00035.00| GUIDE COFFEE FLOW, WELDMENT, GR
3| 1| 1083.00016.00| WASHER, #8 SCREW SIZE, FLAT
4| 1| 1084.00015.00| LOCKNUT, #8-32 SCREW SIZE, HEX THIN NYLON INSERT
5| 2| 1014.00005.00| DISC, GRINDING, 64 MM DIA (One burr attached to a complete rotating disc flange)
5| | 1000.00085.00| KIT: DISC, GRINDING, 64 MM DIA ( Kit of two burrs)
| | 1000.00141.00| KIT: DISC, GRINDING, 64 MM DIA ( Kit of two burrs and #22 burr puller)**
6| 1| 1085.00002.00| SPRING, GRINDER AUGER, 6 MM PITCH
7| 3| 1082.00026.00| SCREW, M4 X 10, PAN HEAD, SLOTTED
8| 1| 1102.00032.00| FRONT GRINDING DISC ASSEMBLY, GR (Flange and burr assembled)
9| 1| 1013.00021.00| WASHER, GR1/GR2 COUNTERSUNK
10| 1| 1082.00027.00| SCREW, M5 X 10, FLAT HEAD, SLOTTED
11| 1| 1102.00036.00| SHAFT AND BEARING ASSEMBLY
12| 1| 1015.00005.00| COVER , GRINDING CHAMBER HSG, MACHINED
13| 1| 1084.00016.00| NUT, M16x1 JAM
14| 4| 1083.00017.00| WASHER, M5, SERRATED BELLEVILLE
15| 4| 1082.00028.00| SCREW, M5 X 12, HEX HEAD
16| 4| 1083.00023.00| WASHER, 1/4″ SCREW SIZE, FLAT
17| 4| 1083.00021.00| WASHER, 1/4″ SCREW SIZE, SPRING LOCK
18| 4| 1084.00017.00| NUT, HEX, 1/4″-20
19| 1| 1102.00035.00| PLATE ASSEMBLY, GRINDER MOTOR
20| 1| 1102.00037.00| COMPLETE GRINDING MOTOR ASSEMBLY, 120VAC/60Hz
20| 1| 1000.00078.00| COMPLETE GRINDING MOTOR ASSEMBLY, 230VAC/50Hz
21| 1| 1087.00003.00| PIN, SLOTTED SPRING, M3x14mm
22| | 1105.00005.00| Burr Puller, (not included, sold only as an aftermarket accessory)
23| 3| 1082.00026.00| SCREW, M4 X 10, PAN HEAD, SLOTTED
24| 1| 1102.00031.00| ROTATING DISC, FLANGE & WASHER, ASSEMBLY, GR
25| 1| 1083.00015.00| RUB WASHER, 1.25″OD X 0.900″ID, FLAT (-requires RED Loctite®)

GRS-1202 Hopper Assembly, Part # 1109.00019.00 [ORDER AS A066]

GRS-1202 Hopper Assembly, Part # 1109.00019.00 [ORDER AS A066]

Wiring Diagram

Go to fetco.com for the latest versions of all information

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>