PROLED L6OP7QLx OPAL Quintopus Linear Installation Guide
- September 17, 2024
- PROLED
Table of Contents
PROLED L6OP7QLx OPAL Quintopus Linear
Product Information
Specifications
- Input Voltage: 220-240VAC
- Manufacturer: MBN GmbH
- Address: Balthasar-Schaller-Str. 3, 86316 Friedberg – Germany
- Website: www.proled.com
Product Usage Instructions
Safety Precautions
Before starting the installation process, please ensure to follow these safety
precautions:
- For indoor use only.
- Dispose of packaging in a safe environment.
- Do not use the luminaire if the cable is defective.
- Installation should be done by a qualified electrician.
- Avoid looking directly at the lighted lamp.
Installation Steps
Follow these steps carefully to ensure proper installation and avoid damage to
the LED:
- Switch off the electricity at the mains and remove the appropriate circuit fuse.
- Connect the light to a power supply or dimmer.
- Connect the primary side of the driver to the power supply (230VAC).
- Ensure all connections are tight with no loose strands.
- Check fire regulations compliance during installation.
- If unsure about any step, consult a qualified electrician.
Detailed Installation Sequence
Follow this specific sequence during installation to prevent LED damage:
- Install LED driver (not included).
- Install LED driver (not included) with input voltage of 220-240VAC.
FAQs
Q: Can the product be used outdoors?
A: No, this product is designed for indoor use only.
Q: What should I do if the cable is damaged?
A: Do not use the luminaire if the cable is defected. Contact a qualified electrician for repair or replacement.
Q: Can I cover the lamps with heat-insulating materials?
A: Do not cover the lamps with heat-insulating materials as it may cause overheating.
Characteristics
- OPAL SHAPE 2G Super Warm White, Warm White, Neutral White or RGB
- Power consumption 15 – 18,5 W/m
- Max. Light hose length 20 m (MONO)
- Metall housing rectangular
- Mounting ring colour is White, Black, or Gold
- Power supply 24 VDC
- Dimmable with a complying PWM dimmer and controller
- Operating temperature range -10° C till +45° C
- CE compliant with applicable European directives
Warning:
- For indoor use only
- Please ensure that the packaging is disposed of in a safe environment
- If the cable is defective, do not use luminaire
- We do recommend that a qualified electrician should be used to install the products
- Do not look at the lighted lamp directly
Safety indices
Be sure to have a qualified electrician complete the installation. The customer is not entitled to claim for any lights installed without observing European safety directives. The manufacturer is then discharged from liability when damage is caused by improper use or installation. If any luminaire is subsequently modified, the person responsible for the modification shall be considered as manufacturer. Do not cover lamps with heat-insulating materials. For indoor use only. Protection class IP20.
Installation
Please follow the sequence of installation step by step. Non-observance can lead to damage to LED.
- Switch off the electricity at the mains before commencing installation or lamp change and (if a fuse box is installed) remove the appropriate circuit fuse to avoid accidental switching on of the mains supply.
- Connect the light to a power supply (secondary side) or a dimmer
- Connect the primary side of the driver to the power supply (230VAC)
- Make sure all connections are tight with no loose strands
- Ensure fire regulations are not breached when fitting your lights
- If you are in any doubt regarding these instructions, consult a qualified electrician
Please follow the sequence, if not destroying of LED:
Remark to the energy efficiency class of the light source
This product contains a light source of energy efficiency class F:
Attention:
- This product counts as a „containing product“ according to directive (EU) 2019/2020 and (EU) 2019/2015.
- The light source is part of the containing product. A separation of the light source and the containing product using commonly available tools is possible with this product.
- Replacement of the light source using commonly available tools is possible with this product.
- The light source can be separated for testing purposes.
- Installation and commissioning may only be performed by qualified persons.
- National installation regulations must be observed.
- Luminaires must be disconnected from the mains before any work.
MBN GmbH
- Balthasar-Schaller-Str. 3, 86316 Friedberg – Germany
- www.proled.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>