PROLED L65XT00 Flex Strip XTREME MONO User Manual

PROLED L65XT00 Flex Strip XTREME MONO User Manual

Unpacking

Reel Packaging
Note: Two people are needed to uncoil the light.

Technical Data

1. 1. Dimensions  13,5 x 6 mm
2. Min. bend diameter 50 mm
3. The product IP rate is ultimately in line with properly applied IP-rated connectors
4. Working ambient temperature -20°C – 45°C.
5. This product contains a light source of Energy class G
6. The light source in the containing product can not be replaced.

Note
Max. length per power input: Indoor (constant temperature) singel end max. 10 m, double end max. 20 m. Outdoor (because of temperature fluctuations and different thermal expansion coefficients of the materials) max. 7m

Light colour

| Cuttable all

| LEDs per segment

| LED power

---|---|---|---
White

| 8,33 cm| 7| 12 W/m
Neutral White

| 8,33 cm| 7| 12 W/m
Warm White

| 8,33 cm| 7| 12 W/m

Cautions

1.  Before making any cuts, installation, maintenance or connection, be sure the mains is disconnected!
2.  Note: all connector joints must be connected correctly to achieve IP67 rating.
3.  Please operate this flex light by instructions, and confirm the work voltage, it must match with product requirements.
4.  Please confirm the polarity of the connector before insertion front connection cable.
5.  Connect and cut this product correctly. Any wrong operation will damage this product.
6.  Use a qualified DC power supply.
7.  Please use and bend this flex strip Xtreme correctly. See the figures on the right.
8.  Do not operate light when ambient temperature exceeds the range of specified temperature in User Manual.
9.  Do not energize the light over 30 minutes in coil packaging.

Cutting instructions

Note

1.  Place the Flex Strip Xtreme horizontally when cutting it.
2.  Use only factory-recommended cutter.
3.  Cut the Flex Strip Xtreme according to the following instructions. The incorrect operation will damage the Flex Strip Xtreme.

IP67 connector

Please ignore these steps, if the front connector has been assembled before delivery.

Components of Front Connector
Note:
The Flex Strip Xtreme ends are marked with either an 01 or an 02. Always make sure to use an identically labeled connector for the

**Installation Steps

**

Inducing a Cavity for Feed Connector

Insert the inducer to the backside of PCB around 10~12mm, and move the inducer up and down 3~5 times gently to create a small cavity.

Inserting the Feed Connector

Treatment of Anti-skidding Clip

Installation of Anti-Skidding Clip

Please energize the Flex Strip Xtreme to check its functionality and do waterproof reliability testing after connector assembly.

IP67 End cap

Please ignore these steps, if the End Cap has been assembled before delivery.

Components of End Cap

Tools

Installation Steps

Inducing a Cavity for Feed Connector

Inserting the Feed Connector

Treatment of Anti-skidding Clip

Installation of Anti-Skidding Clip Fit the anti-skidding clip to the end of the Flex Strip Xtreme so that it wraps tightly and its brim is aligned with the cut edge on both sides. Installation of U Steel Plate and PC Cover

Press the tail plug and tube downwards at the same time till the bottom.

IP40 connector

Please ignore these steps, if the front connector has been assembled before delivery.

1.  Never wet the assembly units or assemble them with wet hands.
2.  Please use the tools correctly.
3.  Please pay attention to personal security when using tools.

Components of Front Connector

The Flex Strip Xtreme ends are marked with either an 01 or an 02. Always make sure to use an identically labeled connector .

Installation Steps

Inducing a Cavity for Feed Connector

Inserting the Feed Connector

Treatment of Anti-skidding Clip

Installation of U Steel Plate and PC Cover

Please energize the Flex Strip Xtreme to check its functionality and do waterproof reliablity testing after connector assembly.

IP67 End cap

Please ignore these steps, if the End Cap has been assembled before delivery.

Components of End Cap

Installation Steps

Inserting the Feed Connector

Treatment of Anti-skidding Clip

Fit the anti-skidding clip to the end of the Flex Strip Xtreme so that it wraps tightly and its brim is aligned with the cut edge on both sides.

Diagram of wiring

1.  This Flex Strip Xtreme must be used in conjunction with 24 VDC power supply
2.  Always observe proper polarity
3.  Ensure to add 20% buffer when sizing power supply
4.  Ensure that the power cable carried current is no greater than 80% of it‘s capacity
5.  To minimize voltage drop and keep light consistency, position power supply nearest to the power feed end of Flex Strip Xtreme and keep the power line as short as possible.

Max. length per power input: Indoor (constant temperature) singel end max. 10 m, double end max. 20 m. Outdoor (because of temperature fluctuations and different thermal expansion coefficients of the materials) max. 7m

Mounting Profiles

Installation Guide

Correct Installation of Standard Aluminum Profile

Requirements and Cautions for Installation of Mounting Profile

Bending in the Process of Installation

Troubleshooting

The whole Flex Strip Xtreme doesn’t work.

• Check power supply is plugged in, switched on and receiving power.
• Check all Flex Strip Xtreme, dimmer or controller connections, connection from the power supply to Flex Strip Xtreme. Check polarity of all wire connections.
• Make sure power supply output voltage is 24V DC.
• Check front connector is inserted into backside of PCB and properly assembled.

Light emitting appear dim or dull at one end

• Check whether the output voltage of the power supply i lower than that of Flex Strip Xtreme.
• Adjust the dimming level to the maximum.
• Power from both ends or shorten Flex Strip Xtreme length to prevent voltage drop.

Light emitting appear excessive brightness

• Check whether the output voltage of power supply is higher than that of Flex Strip Xtreme.
• Check whether the power grid is stable.

If the first segment doesn’t work

• Cut not in indicated cutting line or not in a straight line. Cut out and remove the first segment.
• Damage caused to the first LED when inserting the front connector to the right side of PCB. Cut out the first segment and properly assemble connector.
• Water ingress due to poor connector assembly could cause a short circuit of first segment. Replace length with a new one. External impact damage inside LEDs. Only use your hands to install Flex
• Strip Xtreme into aluminum profile.

Flex Strip Xtreme is flashing on and off.

• Check the power supply to ensure it supports the length you are using. Select the appropriate strength or install an additional power supply to support your installation.
• Check power supply output voltage is stable.
• Check front connector is properly installed with good contact with the copper PCB.
• Check proper controller is connected for Flex Strip Xtreme working

References

• PROLED: proled.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>