PROLED L6OP004 Flex Strip Opal Berlin Instruction Manual
- October 27, 2023
- PROLED
Table of Contents
Installation manual
PROLED FLEX STRIP OPAL
BERLIN / HAMBURG / LONDON /LIVERPOOL / MILAN / SIDE VIEW L6OPxxx
Characteristics:
- SMD CHIP MONO (white, neutral white, warm white, super warm white, ultra warm white) as well as RGB.
- Power supply 24 VDC.
- Homogenous light. No single points visible.
- Safety class IP54. Suitable for wet room.
- Operating temperature range -10° C till +45° C.
- CE compliant with applicable European directives.
Warning:
- For indoor use only.
- Please ensure that the packaging is disposed of in a safe environment.
- We do recommend that a qualified electrician should be used to install the products.
- Do not look at the lighted lamp directly.
Safety indices:
Be sure to have a qualified electrician complete installation. The customer is not entitled to claim for any lights installed without observing European safety directives. The manufacturer is then discharged from liability when damage is caused by improper use or installation. For indoor use only. Protection class IP40.
Preinstallation:
Please follow the sequence of installation step by step. Non-observance can
lead to damage of the flex strip.
- Switch off the electricity at the mains before commencing installation or lamp change and (if a fuse box is installed) remove the appropriate circuit fuse to avoid accidental switching on of the mains supply.
- Connect the flex strip to the power supply 24 VDC output (secondary side).
- Connect connector (primary side) of power supply to mains (220-240VAC).
- If a dimmer is used, than it must be placed between power supply and the flex strip.
Installation possibilites:
-
Please keep in mind, that following strain is not allowed:
-
Minimum bending diameter at FLEX STRIP OPAL LONDON, LIVERPOOL & MILAN
-
Minimum bending diameter at FLEX STRIP OPAL BERLIN, HAMBURG & SIDE VIEW
Installation:
-
Installation with short profiles
Short fixing profiles must be in level. It is recommended to use at least two short fixing profiles each meter. -
Procedure during mounting and demounting
| Simultaneously install from both ends
---|---
| Installation from one side is not allowed
| Min. 2 Persons needed at a length of more than 2m.
| Please use tools when removing strip out of profile. Do not bend more than 15°
| Pulling on strip is not allowed and results in strip damages.
| Min. 2 Persons needed at a length of more than 2m. -
Preparing of strip
Cut straight, along the cutting marks.
| Put the cable through end cap. Fill in 1/3 – 1/2 end cap with glue
---|---
| Put the end cap on the strip. Laid flat for 2 hours.
| Put glue on the strip.
Place end cap on the strip Laid flat for 2 hours.
The glue is dry after 24 hours
Energy efficiency class of the light source:
Products listed in this manual contain a light source of following efficiency class, listed according to the item codes:
Item code | Efficiency class of light source |
---|---|
L6OP0xx | G |
L6OP0xx2G | F |
L6OP1xx | G |
L6OP1xx2G | F |
L6OP2xx | G |
L6OP2xx2G | F |
L6OP30x | F |
L6OP326 | G |
L6OP336 | G |
L6OP3xx2G | F |
L6OP4xx | G |
L6OP4xxDx | G |
L6OP4xx2G | F |
L6OP5xx | G |
ATTENTION:
Installation and commissioning may only be performed by qualified persons.
National installation regulations must be observed.
Luminaires must be disconnected from mains before any work.
The product is a “containing product” according to directive (EU) 2019/2020
and (EU) 2019/2015.
The light source is an integral part of the containing product. Separating of
light source and containing product results in irreversible damage. Exchange
of the light source with commonly available tools is not useful for this
product.
03.22 Technical amendments reserved
MBN GmbH, Balthasar-Schaller-Str. 3, 86316 Friedberg – Germany
www.proled.com
Documents / Resources
|
PROLED L6OP004 Flex Strip Opal
Berlin
[pdf] Instruction Manual
L6OP004, Flex Strip Opal Berlin, L6OP004 Flex Strip Opal Berlin, Strip Opal
Berlin, Opal Berlin
---|---