FORTIN F250 Evo-All Push to Start Ford Vehicle Installation Guide

FORTIN F250 Evo-All Push to Start Ford Vehicle

STAND ALONE INSTALLATION

NOTES

• The vehicles OEM remote will still operable during remote start.

MANDATORY INSTALL

HOOD PIN

• HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.

Notice: the installation of safety elements are mandatory. The hood pinis an essential security element andmust be installed.

THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

PARTS REQUIRED (NOT INCLUDED)

Notice: the installation of safety elements are mandatory. The hood pin and the valet switch are essential security elements and must be installed.

STAND ALONE CONFIGURATION

REMOTE STARTER FUNCTIONALITY

• All doors must be closed.
• Press the OEM remote’s Lock button 3x to remote-start (or remote-stop) the vehicle.
• The vehicle will START.

REMOTE STARTER WARNING CARD

CUT THIS WARNING CARD AND STICK IT ON A VISIBLE PLACE: or use the package RSPB, Sold separately.

WARNING

REMOTE STARTER
THE VEHICLE CAN BE STARTED BY EITHER: PRESSING THE LOCK BUTTON ON THE OEM REMOTE 3 TIMES  CONSECUTIVELY OR BY ASMARTPHONE. TURN ON THE SAFETY SWITCH LOCATED UNDER THE  DASHBOARD BEFORE WORKING ON THE VEHICLE.

THE REMOTE START WILL NOT OPERATE IF

• Hood is open or switch is not present
• Check Engine light is ON  Low fuel light is ON
• Vehicle battery voltage is too low

CAUTION

• The remote start is limited to two consecutive command Start or Stop.
• To use the remote again ignition must be turned ON and OFF.

AUTOMATIC TRANSMISSION WIRING CONNECTION

DCRYPTOR PROGRAMMING PROCEDURE

1. Press and hold Insert the  programming button: the 4-Pin (Data-Link) connector.
   • The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
2. Release the programming button when the LED is BLUE.
3. If the LED is not solid BLUE disconnect the 4-Pin connector (Data-Link) and go back to step 1.
4. Insert the required remaining connectors.
5. Do not press the brake pedal. Press the Push-to-Start button once to turn on the ignition.
   • The BLUE LED will turn OFF.
   • The BLUE, YELLOW and RED LEDs will alternated.
   • The RED and YELLOW LEDs will alternated.
   • Make sure that the DELs are flashing RED and YELLOW before continuing programming.
   • Press the Push-to-Start button once to turn off the ignition.
   • The RED and YELLOW LEDs alternate. KEY BYPASS PROGRAMMING PROCEDURE
6. Disconnect all the connectors and after the Data-Link (4-pins) connector.
7. Use the tool: FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.
   • Parts required (not included)
8. AFTER DCRYPTOR PROGRAMMING COMPLETED Go back to the vehicle and reconnect the 4-Pin (Data-Link) connector and after, all the remaining connector.
   • The BLUE LED will turn ON.
9. Do not press the brake pedal. Press the Push-to-Start button once to turn on the ignition.
   • The BLUE, YELLOW and RED LEDs will alternated.
   • The BLUE LED will flash rapidly.
10. Press the Push-to-Start button once to turn off the ignition.
    • The BLUE will turn OFF.

The module is now programmed.

OPTIONAL RF-KIT PROGRAMMING

PROGRAM BYPASS OPTION

OPTIONAL FORTIN RF KIT SERIES 4 OR SERIES 9 PROGRAMMING

• The module must be programmed on the vehicle.
• MAKE SURE THE IGNITION KEY HAS BEEN IN THE OFF POSITION FOR AT LEAST 5 SECONDS.

REMOTE STARTER FUNCTIONALITY

Notice: Updated Firmware and Installation Guides Updated firmware and installation guides are posted on our web site regularly. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) before the installation of this product.

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer-safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever about the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or in any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by a qualified technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

TECH SUPPORT

• Tél: 514-255-HELP (4357)
• 1-877-336-7797

ADDENDUM GUIDE

• www.fortinbypass.com

References

• The domain name off.la is for sale
• wah damn solid

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>