ETERNICO AET-RLR8 LED Ring Light User Manual

LED Ring Light
AET-RLR8
User Manual

THANK YOU FOR CHOOSING US!

We value your trust. We hope that you will be happy with our product, and as excited about it as we are. We try to offer products of the highest quality that satisfy even the most demanding requirements. If you are satisfied, it would make us very happy if you chose us again the next time you make a purchase. We are environmentally conscious, therefore we use special eco- friendly packaging. Please recycle!
Recycling and Environmental Protection
We try to avoid using plastic packaging and film and only use them when they are absolutely necessary to protect the product. So how are we different? Packaging you can eat… Well, almost. 🙂
We use ink made from soybeans as opposed to classic petroleum-based ink.
The majority of our packaging is made from 100% recyclable paper.
****We limit the use of adhesives. If absolutely necessary, we make sure to choose only wa-ter-soluble ones.
We think globally, which means that we actively search for eco-friendly solutions. We keep an eye on trending technology and place findings of the scientific community into practice. We don’t just try to meet quotas and mandates, we aim to exceed them.

TECHNICAL PARAMETERS

OVERVIEW

LED light

1. LED light
2. Adapter for connecting external devices with 3/4 thread (holders, flashes, etc.)
3. USB cable with controller
4. Mobile phone holder
5. Mounting fastening ring

USB controller

USB controller

1 COLOR button| Press repeatedly to change the color of the white light (cold white -natural white – warm white).
---|---
2 RGB button| Press repeatedly to change the RGB light color. (up to 15 colors).
3 UP button| Press briefly to increase the brightness of the light by 10 %; press and hold to adjust the light intensity continuously.
4 DOWN button| Press briefly to lower the brightness of the light by 10 %; press and hold to adjust the light intensity continuously.
5 MODE button| Press briefly to select from 9 color modes; press and hold for 1 second to lock or unlock the currently set mode (color skip mode or flash mode cannot be locked).
6 ON/OFF button| Press briefly to turn the LED light on or off.

Note:
The LED light is equipped with the function of saving the last setting in memory. If you turn off the LED light with the ON / OFF button and do not disconnect it from the power supply, the LED light will turn on in the last setting made when the LED light is turned on again with the ON / OFF button.

Remote control

Remote control

1. Brightness dimming button
   Press briefly to lower the brightness of the light by 10 %; press and hold to adjust the light intensity continuously.

2. Brightness up button
   Press briefly to increase the brightness of the light by 10 %; press and hold to adjust the light intensity continuously.

3. RGB light color selection buttons (up to 15 colors)

4. OFF button
   LEDlight off

5. ON button
   LED light on

6. White light color selection buttons
   (cold white – natural white – warm white)

7. MODE button
   A short press will switch between the differ-ent light modes (skip color mode or flashing mode cannot be locked).

8. S ± button
   Speed setting in color flash mode; there are a total of 3 speeds to choose from.

Note: The remote control is supplied with a 3V battery type CR2025. For protection during transport and premature discharge, the battery is provided with a protective foil. Before using the re-mote control, remove the protective foil by pulling it out of the battery compartment.

Battery replacement
When the battery is empty and the remote control no longer works, the battery needs to be replaced.

1. Carefully push the latch on the bottom of the remote control to the right and remove the battery holder.

2. Remove the empty battery from the holder and insert a new one. Always observe the cor-rect polarity of the battery.
   It is marked on the holder.

3. Insert the holder with the new battery back into the remote control.
   Warning:
   Dispose of the used battery in accordance with local regulations. Do not dispose of the battery in mixed household waste. Do not throw the batteries in a fire. It could explode or leak electro-lyte. Do not short-circuit, disassemble or deform the battery.
   Use
   Plug the USB control into a USB-A port. The recommended power is at least 15 W.

SAFETY INFORMATION

• Read the safety and operatinginstructions. Failure to observe the safety and operating instructions can endanger people or damage the device. And it may void your warranty.
• This product is only suitable for household use.
• This product is not a toy. It may contain small components. Please keep away from children.
• Do not use or leave the product in a dusty or otherwise polluted environment.
• Do not leave the product in high or low ambient temperatures. Keep the product in a dry environment.
• Keep this product away from heat sources such as stoves or direct sunlight. No naked flame sources, such as lighted candles, should be placed on the product.
• Do not expose the product to dripping or splashing water or other liquids. Do not place containers filled with water, such as vases, on the product.
• Do not touch the product with wet hands.
• This product is not considered a light fixture. Make sure that continuous operation does not exceed six hours.
• Never look into the light for a long time. There is a risk of serious eye damage.
• Do not disassemble the product. Attempting to modify the power bank may damage the product and result in a serious injury.
• Do not immerse the product in water or other liquids or throw it into a fire.
• Do not leave the product unattended while it is in operation.
• Avoid turning the product on and off frequently and repeatedly.
• While the product is in operation, it may become hot. This is a normal occurrence. There-fore, make sure that there are no heat-sensitive objects / surfaces near the product.
• If you notice an unpleasant odor or smoke while using the product, unplug the product immediately and stop using it. Contact an authorized customer center.
• Avoid overloading the product. Avoid dropping the product.
• Do not place any objects on the product. There is a risk of irreversible damage to the product.
• This product does not contain parts repairable by the user. In the event of a malfunction or defect contact the nearest authorized service center. Check it regularly for damage.
• Use only a soft, clean, dry cloth to clean the surface.
• Do not use any chemical cleaners, abrasives, gasoline, thinners or other similar substances. Before cleaning, make sure that the product is disconnected from the power supply.
• Store the product in a dry and well-ventilated place. Do not place any objects on the prod-uct when in storage.

DISPOSAL OF USED BATTERIES

• Batteries contain materials harmful to the environment. Do not dispose of bat-teries in a regular community waste. Dispose of used batteries properly at col-lection points.

www.eternico.net
Co. Reg. No. 27082440
Alza.cz a.s., Jankovcova 1522/53, 170 00 Prague 7, Czech Republic © 2021 Alza.cz a.s.
All Rights Reserved.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>