NEWLUX Azul Secadry XXL Instructions

NEWLUX Azul Secadry XXL

SAFETY PRECAUTIONS

• Read the instructions in this manual carefully before using the portable dryer. Keep this manual for future reference.
• Check the voltage before connecting to the mains (AC 220-240V, 50/60Hz). Connecting it to the wrong voltage may damage it.
• Do not share the power supply with other electrical appliances with high power consumption.
• To avoid electric shock, please do not immerse the appliance, plug, or power cord in water or other liquids.
• Do not leave this appliance unattended while in operation.
• Designed for indoor use only. This product may not be used outdoors, in the bathroom, or in wet areas.
• Keep the appliance away from flammable materials and chemicals.
• This appliance is not intended for children or persons with impaired physical, sensory, or mental capabilities or those who lack sufficient experience or knowledge, please avoid using it without supervision or instruction from a person who can ensure its safe operation.
• Before putting the laundry into the dryer, for safety, the laundry should be well wrung out and/or spun dry, not dripping. This will prevent them from wetting the floor and the appliance and will shorten the drying time and therefore save energy.
• Do not touch or cover the air outlet when the device is in operation.  Drain clothes thoroughly before inserting them into the structure.
• Do not open when in operation, as the UV light may damage the eyes.
• If the power cable is damaged, it must be replaced by the Official Technical Service or an authorized company.
• Do not keep the device switched on for more than 360 minutes at a time. In case you need to switch it on after this time, leave a 30-minute pause between each cycle.
• To avoid a decrease in drying efficiency, the air inlet filter should always be checked and cleaned.
• To keep the device at its best performance, clean the filter screen at the air inlet at least every 15 days.
• It is suitable for drying clothes with high-temperature resistance, higher than 75°C.

WARNING! Never cover the air vent. Wring the clothes well before putting them into the device, ensuring that they do not drip. Avoid direct contact with UV rays with your skin and eyes.

PARTS AND COMPONENTS

Accessories: Exterior cover or case

Diagram of the product circuit

INSTALLATION

1. On a flat surface, assemble the upper and lower shelf, connecting the pieces, following the drawing shown below:

   • Upper shelf
     

   • Connect the horizontal tubes (C) directly to the hole in the plastic shelf (A).

   • Lower fixed shelf

   • Connect to the lower shelf (A) the horizontal tubes (C) and the four wheels (F) and (G) directly into the hole in the shelf.

2. Connect the lower vertical tubes (E) to the four corners of the lower shelf (A), following the drawing.

3. To assemble the structure, connect the lower vertical tubes (E) and the plastic shelves of the intermediate level (A), as shown in the drawing. Repeat the same process with the upper vertical tubes (D) and (E) and connect the upper shelf (A) (previously assembled in step 1). Finally, connect the 8 intermediate horizontal hanging tubes (B) to the intermediate and lower shelves.

4. With the structure finally assembled, gently place the outer cover on top of the structure from top to bottom. Place the main device (I) in the center of the fixed lower shelf. Close the outer cover to finish assembling the tumble dryer.

5. Dismantling: to dismantle the device, follow the assembly steps in the reverse order.

OPERATING INSTRUCTIONS

1. Connect the supply plug to the electrical current, more than 10A.
2. Place the items of clothing on the shelfs, which have firstly been  wrung out and are not dripping. Close the outer cover.

• 1H PREDETERMINED MODE : After connecting to the power supply the device will turn on. Press the ON/OFF switch to turn on the device. The default time is 1 hour (60 min.) of drying mode.
• TIMER : Press the TIMER button to select the desired drying time. The programming time increases by 10 minutes at a time until it reaches 180 minutes.
• STERILISATION MODE: The UV sterilization function is activated 20 minutes before the previously selected time is up
• WARNING: UNDER NO CIRCUMSTANCES SHOULD THE COVER BE OPENED DURING OPERATION as this could cause skin or eye injuries.

MAINTENANCE AND CLEANING

1. Turn off and unplug the device from the electrical current. Wait until the device becomes cold before starting cleaning.
2. Clean the whole surface and parts with a soft cloth, if necessary you can lightly dampen it with water and soap. The surface must be cleaned to avoid discoloration and damage.
3. If you are not going to use the device for a long period, keep it clean in a dry place with no humidity.
   • Do not submerge the device or its parts in water. Do not use solvents, bleach, or corrosive substances to clean the device.

SOLVING PROBLEMS

TECHNICAL SPECIFICATIONS

• Structural material : Stainless steel 201 (Diameters 25 mm and 19 mm) and PP
• Fabric material: Oxford fabric 210 72 gr
• Dimensions: 700x450x1650 mm.
• Power : 1200W Ceramic PTC heating system
• Drying time : 60 to 180 minutes. 4 wheels, 2 with brake.
• Lamp : Power 1.7W (3W adapter), current 360mA. Voltage radiation intensity 429 μW/cm2 Maximum supported weight 15Kg
• Recommended drying load : < 10Kg of laundry
• Drying capacity >9m
• Input voltage : 220-240V – 50/60Hz
• Product weight : 4 Kg

References

• NewluxGroup – Productos de diseño, honestos, innovadores y de calidad

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>