Newlux W420 WindPure Roof Smart Instruction Manual

Newlux W420 WindPure Roof Smart

Product Information

• Model: Newlux WindPure Roof W420 Smart
• Type: Ceiling Fan
• Languages: English, Spanish, Italian, German, French, Portuguese

Product Usage Instructions

Safety Precautions

If the wires are damaged, do not use the fan. It must be replaced by the official technical service.

Assembly

1. Do not use the fan without having previously assembled it.
2. Attach the suspension bracket to the ceiling joist or to a suitable wooden support inserted between the ceiling joists. The bracket must be fastened with the two long screws supplied.
3. Install the down rod with an electric cable and connect it to the upper and lower brackets.

Receiver

1. Connect the power live wire (brown) to the L terminal of the receiver.
2. Connect the power neutral wire (blue) to the N terminal of the receiver.

Use and Operation

1. Use the provided balancing kit if the fan becomes unbalanced during operation.
2. Use the control panel to adjust the fan speed (low, medium, high), turn the light on/off, and set a timer (2H, 1H, 4H).

Maintenance and Cleaning

1. Refer to the user manual for specific maintenance and cleaning instructions.
2. Visit newluxgroup.com for additional information and support.

SAFETY PRECAUTIONS

Before you start

• Read the instructions in this manual carefully before using the device. Keep this manual for future reference.
• The installation work must be performed by a qualified wiring installer.
• Disconnect the mains at the fuse box.
• Do not leave the fan running unattended.
• Do not immerse the device in water or pour water over it.
• Do not place the fan near sources of heat.
• Do not allow children to handle the fan. It could be dangerous and must not be used by children.
• If the device has any damaged parts, do not use. Contact the seller or the Technical Service (SAT).
• Do not expose the device to sunlight or the elements.
• This device is designed exclusively for domestic use. Do not use for functions not indicated in this manual.
• The device must be handled only by designated Newlux service technicians. Do not disassemble or tamper with the product; there is a risk of fire, electrical shock or personal injury.
• This device must NOT be used by persons with a lack of experience and knowledge due to reduced physical, sensory or mental capabilities (including children), unless they are supervised or instructed in the use of the device by a person responsible for their safety.

WARNING

• If the wires are damaged, do not use the fan. It must be replaced by the official technical service.

Safety in use

• After removing the packing material, check the integrity of the fan.
• It is an electrical device, so appropriate safety precautions must be observed. Make sure the operating voltage of the fan corresponds to that of the electrical supply.
• The ceiling mounting hook must be capable of supporting a weight of 16 kg.
• The ceiling fan must be mounted at a minimum height of 2.4 m from the floor.
• Do not place any objects in the path of the blades.
• Once all electrical connections have been made, store all wires neatly.
• Make sure all screws and connections are tight and secure.
• Keep the fan away from textiles (e.g. fabrics, curtains and sofas).
• When mounting the fan, make sure that the safety cable is coiled on the mounting hook on the cell.
• Do not use flammable materials or aerosols near the device.
• If the fan fails or malfunctions, turn it off and contact the dealer or Technical Services (TAS).

ASSEMBLY

WARNING: Do not use the fan without having previously assembled it.
To assemble the fan, please refer to the images shown below.

Suspension bracket installation

1. Attach the suspension bracket to the ceiling joist or to a suitable wooden support inserted between the ceiling joists.
2. The bracket must be fastened with the two long screws supplied.

Product parts

Installing the down rod bracket

1. Pass the opening of the upper bracket up along the down rod.
2. Next, pass the opening of the lower bracket.

Steps to follow in the installation of the motor

1. Insert the down rod into the coupler.
2. The plastic blade is designed for easy installation of the fan motor. Insert the blade into the motor housing recess directly and fasten with the screws.
3. Place the upper bracket on the hanging bracket.
4. L= L Connect to fan power cable L (brown)
   N= N Connect to fan neutral cable N (blue)

Install the bracket to the ceiling

Point 3. Close with quick connector and fi x the LED ceiling light with the help of the magnets. Then turn the ceiling light to the right to keep it fixed.

Fan bracket installation

Fan balancing
If the fan becomes unbalanced during operation, perform the following steps to troubleshoot the problem:

1. Tighten all screws.
2. Unscrew the blades and fix them in the different position combinations on the motor.
3. Measure the level between the ceiling and all blades.
4. Use the supplied blade balancing kit if the fan still wobbles.

USE AND OPERATION

Before each use, check that the unit is in good condition and that the electrical system is not damaged. If the electrical system is damaged, contact the seller or the Technical Assistance Service (TAS).
Device operation
Turn on the fan by pressing the speed button of your choice through the remote control. Remember to turn on the switch in the room where the equipment is installed firstly.
Remote control
To operate the device with the remote control, you must point it at the fan.

• Press the LIGHT button to make the fan illuminate or turn off the room light.
• Press the LOW, MED, HI button to start the fan running. You can select the level of air speed you want to program: low (night), medium (eco), and high (power).
• Press the STOP button to stop the fan from running.

Timer

This appliance has a timer with automatic shut-off.
Press the 1H, 2H and 4H button to set the auto power off time you want to program.

Inverter function Summer/Winter
Change the direction of rotation of the blades according to the time of year so that in winter the heat from the heater is distributed evenly and in summer it cools the room constantly with the movement of the air.

MAINTENANCE AND CLEANING

• Due to the natural movement of the fan, the connections may loosen after a period of use. To ensure correct and safe use, it is recommended that all connections be inspected and tightened every 6 months.
•  Clean the main body with a soft, slightly damp cloth. Do not use abrasive or corrosive products. Rough fabrics will scratch the surface.
•  To cover small scratches, apply a light coat of shoe polish
• It is not necessary to oil the fan.
• Do not immerse any part of the fan in water or other liquid. Should this occur, do not dip your hand into the liquid, but first remove the plug from the socket.
• Carefully dry the device and make sure that all electrical parts are dry.
• If you are not going to use the fan for a while, you should protect it from dust and humidity; it is recommended to store it in its original packaging.

TECHNICAL DATA

• Dimensions: 106cm. Ø
• Power: 60W
• Voltage (V): AC220V
• Frequency (F): 50Hz
• Main material: ABS
• Copper motor
• Noise level dB: 46dB
• RPM: 250
• Timer: 4 hours
• Remote control
• Blades: 3
• Speeds: 3

PRODUCT DISPOSAL NB. DISPOSE OF PRODUCT IN ACCORDANCE WITH DIRECTIVE 2011/65/EC.

• At the end of its useful life, you should not dispose of the product as ordinary waste, but take it to a local government waste collection center or a distributor that provides this service.
• Disposing of your appliance this way prevents negative consequences for the environment and health, and means the materials can be recovered for significant savings in energy and resources.
• As a reminder of the need for special disposal of the appliance, it is labelled with a crossed-out rubbish bin.

References

• NewluxGroup – Productos de diseño, honestos, innovadores y de calidad

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>