ATDEC AW-FB Ora Bolt Through Fixing Installation Guide
- September 3, 2024
- ATDEC
Table of Contents
AW-FB Ora Bolt Through Fixing
“`html
Product Specifications:
- Product Name: Ora Bolt Through Fixing
- Model: AW-FB
- Capacity:
- Weight: 2 – 8kg (4.4 – 17.6lb)
- Display Size: Up to 35″ (curved or flat)
- Warranty: 10 Years Limited
Product Usage Instructions:
Component Checklist:
- Arm Spigot (x1)
- Clamp Plate (x1)
- M8 Stud Bolt (x1)
- Clamp Bar (x1)
- M8 Flange Nut (x1)
Tools Required:
- 4mm Hex Key (supplied with Ora arm)
- 8.5mm (or 11/32) drill bit
- Power Drill
- 13mm Spanner
- Phillips head screwdriver
Installation Steps:
1. Drill Hole in the Work Surface:
1.1. Mark out hole position on the work surface using the Clamp
Plate as a template.
2. Attach Arm Spigot to Clamp Plate:
2.1. Drill the hole using a suitable drill bit ensuring it is
perpendicular to the work surface.
2.2. Screw M8 Stud Bolt through Clamp Plate into Arm Spigot and
tighten firmly with the provided 4mm Hex Key.
3. Attach Plate Assembly to Desk:
Place Clamp Bar over M8 Stud Bolt under the desk and secure
Flange Nut with a spanner. Support the plate while tightening to
maintain correct orientation on the work surface.
Tips:
- When positioning the desk clamp, offset it to the left or right
of the seating position for centered monitor placement.
Frequently Asked Questions:
Q: Can larger monitors within the weight capacity be used with
this product?
A: Yes, larger monitors within the weight capacity may be
compatible. Please contact Atdec for advice.
“`
Ora Bolt Through Fixing
Installation Guide
AW-FB
COMPONENT CHECKLIST
Arm Spigot (x1)
Clamp Plate (x1)
M8 Stud Bolt (x1) Clamp Bar (x1)
CAPACITY
Weight: Display Size:
2 – 8kg (4.4 – 17.6lb) Up to 35″ (curved or flat)
(Larger monitors within the weight capacity may be compatible, please contact
Atdec for advice).
WARRANTY
10 Years Limited
TOOLS REQUIRED
4mm Hex Key (supplied with Ora arm) 8.5mm (or 11/32″) drill bit Power Drill
13mm Spanner Phillips head screwdriver
IMPORTANT INFORMATION
·Install Ora Accessories as per these installation instructions.
·The manufacturer accepts no responsibility for incorrect installation.
·The product is compatible with grommet hole sizes up to 80mm (3.15″)
·The product is compatible with desk thicknesses from 0-55mm (0-2.2″).
·Do not over-tighten screws and adjustment points on product.
·This product is not suitable for outdoor use.
·Do not use this product for mobile applications.
·Please ensure desk structure and mounting surface are of sufficient strength
to support this product and mounted equipment.
M8 Flange Nut (x1)
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. ©20231006
1 For bolt through installations, drill hole in the work surface
1.1
Mark out hole position on the work surface. Use Clamp Plate as a template.
2 Attach Arm Spigot to Clamp Plate
HINT!
Hold Arm Spigot and Clamp Plate together, locating the dimple in the slot,
before hand tightening the screw into the spigot.
USER
1.2
Drill the hole using a suitable drill bit. Ensure the
hole is drilled perpendicular to the work surface
and the edges of the clamp are positioned fully
on the desk.
8.5 mm (12″)
Desk
Thickness 18 – 40mm (¾ – 1½”)
40mm (1 “) minimum
TIP When positioning the desk clamp, offset the clamp to the left or right of the seating position. The monitor will then be centred for the user.
Screw M8 Stud Bolt through Clamp Plate into Arm Spigot.
2.2
Tighten firmly with 4mm Hex Key supplied with Arm.
100mm (4”)
3 Attach plate assembly to desk
Place Clamp Bar over M8 Stud Bolt under the desk as illustrated and secure
Flange Nut with spanner.
TIP
Support plate while tightening to maintain the correct orientation on the work
surface.