ATDEC AD-WT-8060 Tilt Wall Mount Installation Guide

June 9, 2024
ATDEC

Infinite Mounting Possibilities
Tilt Wall Mount 8060
AD-WT-8060
Installation Guide
ATDEC AD WT 8060 Tilt Wall Mount -

COMPONENT CHECKLIST

ATDEC AD WT 8060 Tilt Wall Mount - COMPONENT CHECKLIST

NOTE:
! Wall Plate Mounting Fasteners are NOT supplied with Wall Mounts.
Professional installer to ensure correct Mounting Fastener type, location & quantity to suit structure where Wall Mount is installed.
! ALWAYS use a washer between the chosen fastener and the wall plate.
! Mounting fasteners to be used as per manufacturers instructions, including minimum engagement to achieve necessary performance.

REQUIRED TOOLS

  • Phillips head screwdriver
  • Power drill
  • Suitable drill bit
  • Driver bit for selected wall fasteners
  • Stud finder
  • Spirit level
  • Socket wrench set

WEIGHT RANGE
0 – 80kg
(0 – 176lb)

IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! The manufacturer accepts no responsibility for incorrect installation.
! Failure to mount this product correctly may cause serious injury/death during or following installation.
! This product is not suitable for outdoor use.
! Do not use this product for mobile applications.
! Wall Plate only achieves maximum weight rating when appropriately fastened to a wall of adequate structural capacity.
! Professional installer to ensure adequate structural capacity of wall (including appropriate safety factor) to support total weight of all equipment being mounted.
! Drilling into electrical wires can cause death – use appropriate equipment and caution when drilling holes in walls to avoid electrical cables, water pipes and gas pipes. Do not drill into structures unless you have established it’s safe to do so.

Mount the Wall Plate to the Wall

ATDEC AD WT 8060 Tilt Wall Mount - Plate to the Wall

NOTE:

  • Choice and supply of appropriate wall plate fasteners is the responsibility of the installer.
  • Consult a preferred fastener supplier or a structural engineerto select fasteners which are most appropriate for the weightof the display and wall construction method.
  • Wall plate must be level. Verify using a quality spirit level tool.
  • On a Stud Wall or Drywall use a good quality Stud Finder to position mounting fasteners in the centre of studs.
  • On a Masonry Wall avoid positioning Wall Plate mounting fasteners in a mortar join.

ATDEC AD WT 8060 Tilt Wall Mount - example only

*Fasteners shown are for example only

Attach the Display Brackets to the Display

ATDEC AD WT 8060 Tilt Wall Mount - Brackets to the
Display

NOTE:

  • Always use multi-washers M-F.
  • Ensure the display brackets are not loose and screws are not forced too deep into the display.
  • If spacers are needed, use the shortest possible combination between the display bracket and the display.

ATDEC AD WT 8060 Tilt Wall Mount - Attach the Display

Hook and Secure the Display onto the Wall Plate

3.1. Angle the display and hook the Display Brackets over the top of the Wall Plate.
This should be completed by two people

ATDEC AD WT 8060 Tilt Wall Mount - completed by two
people

NOTE:
Ensure level adjustment screws are retracted prior to mounting the display.

3.2. Slide Security Bar D through the slots at the bottom of each Display Bracket, ensuring the Security Bar sits to the rear of the Wall Plate and the display cannot be lifted up and off the Wall Plate.
3.3. (OPTIONAL) To prevent theft of the display, add a padlock to the end of Security Bar D.ATDEC AD WT 8060 Tilt Wall Mount -
padlock

ADJUSTMENTS

ATDEC AD WT 8060 Tilt Wall Mount - ADJUSTMENTS

If needed, carefully turn the screws at the top of each display bracket clockwise using Hex Key E to level the display.

NOTE:
Support display whilst turning the level adjustment screws.

ATDEC AD WT 8060 Tilt Wall Mount - Display Tilt

Remove the black plastic caps from Display Brackets B and C.
Tilt the display to the desired viewing angle and tighten the nuts using a suitable socket wrench tool to lock the angle in place.

No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. ©20220323
Please Recycle
AD-WT-8060

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

ATDEC User Manuals

Related Manuals