ATDEC AWMS-2-BT75-H-B Desk Mount For Monitor Display Installation Guide
- June 13, 2024
- ATDEC
Table of Contents
- AWMS-2-BT75-H-B Desk Mount For Monitor Display
- COMPONENT CHECKLIST
- Assemble post to clamp
- Fit clamp to work surface
- Attach VESA plates to displays
- Slide brackets onto post and set height
- Attach bottom display
- Set tilt
- Attach top display
- Fine adjustment
- Cable management
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Infinite Mounting Possibilities
Installation Guide
AWMS-2-BT75-H
Post Mounted Heavy Duty
Dual Vertical Monitor Mount
Heavy Duty F Clamp
AWMS-2-BT75-H-B Desk Mount For Monitor Display
https://atdec.qrd.by/awms-2-bt75-h
COMPONENT CHECKLIST
REQUIRED TOOLS
- Phillips Head Screwdriver
CAPACITY (per monitor)
Flat Monitor
4.5 – 25kg (10 – 55lb)
Curved Monitor
4.5 – 18kg (10 – 40lb)
Display Size
24” – 55”
300mm (12”) max overall display depth
IMPORTANT INFORMATION
! Product should only be assembled and used as per these installation
instructions.
! The manufacturer accepts no responsibility for incorrect installation.
! Each bracket supports a maximum weight as per above capacity specification.
! Avoid applying downward load to corners of display.
! Product must only be installed on a solid work surface capable of supporting
the weight of all equipment being mounted.
! This product is not suitable for outdoor use.
! Do not use this product for mobile applications.
! VESA mounted accessories (such as mini PC brackets and mounts), and offset
VESA locations exert additional leverage that can exceed the capacity of the
mount even though the monitor weight may be within the stated range. Please
contact Atdec if you would like further information.
! WARNING! Death or serious injury may occur if a child climbs on or tips
product.
Assemble post to clamp
1.1 Attach post to upper clamp using the M8x60mm screws and 5mm hex key. 1.2 Measure the worksurface thickness and choose the suitable lower clamp position. 1.3 Attach lower clamp to upper clamp in the suitable position using the M8x16mm screws and 5mm hex key. Note: If there is only a small gap behind the worksurface perform Step 2.1 before this step
Fit clamp to work surface
2.1 Place in desired location on worksurface. 2.2 Screw in both pressure plates and tighten evenly and firmly. 2.3 Remove clips & covers from post by sliding up & out or by squeezing sides.
Attach VESA plates to displays
3.1 VESA compatibility.
NOTE: Some displays require the use of a VESA adapter before attaching
the VESA plate. This VESA adapter may ship in the box with the display.
Consult your display’s installation guide for further information.
Option A
Attach VESA plate with M4x10mm screws. Option B
For recessed VESA use 10mm spacers and M4x20mm screws.
Slide brackets onto post and set height
4.1 Tilt bracket must only be attached with display facing the front of the
mounting surface. 4.2 Line up the
inner guide on rear of bracket with rear channel on post.
Slide inner guide into channel, then lower bracket. 4.3 Firmly tighten hand
knob at chosen height.
Ensure height is sufficient for display to clear desk once in place.
Repeat with second bracket and fit post cap. WARNING: Never loosen knob while display is on bracket
Attach bottom display
5.1 Set VESA plate clips to open position.
Bottom display must be attached to bracket first.
WARNING: Use two people to install display 5.2 Lift display until VESA
plate is above the bracket. 5.3 Centre VESA
plate close to post and slowly lower until bar on VESA plate sits in saddle in
bracket. 5.4 Set VESA plate clips to closed position.
NOTE: Display hangs from the bracket like a painting. After clips are
closed, if corners of the screen are pushed downwards, rocking movement is
expected.
Set tilt
6.1 Adjust display tilt angle by gripping edges of screen and rolling up or
down to desired position. OPTIONAL ADJUSTMENT – TILT FRICTION
4mm hex key can be used to reduce tilt friction (for light screen) or increase
tilt friction (for heavy screen). 6.2 Set display angle by tightening tilt
knobs.
Attach top display
7.1 Check that distance between brackets is equal to or greater than the
height of the display. (See image in Step 4.3)
WARNING: Damage to monitors may occur if there is insufficient spacing
between brackets. Top monitor must hang in bracket – not be held up by the
monitor below it. After both displays are attached, use fine adjustment to
close gap between them (see Step 8).
7.2 Repeat Step 5 & Step 6 to attach top display and set tilt angle.
i Lower
ii Close
iii Adjust angle
iv Set angle
Fine adjustment
8.1 To correct horizontal angle of display +/- 3 °:
Turn a single fine tune adjustment knob to adjust angle of screen.
Clockwise = Higher
Anti-clockwise = Lower8.2 To close small
gap between displays +/-6mm (1/4”):
Turn both fine tune adjustment knobs – alternating sides a few rotations at a
time.
Clockwise = Higher
Anti-clockwise = Lower
Cable management
9.1 Load cables into cable clip. 9.2 Insert one side of the cable clip into a channel on the post, then push in the other side. 9.3 Load cables into cable cover. 9.4 Clip the cable cover back onto rear post channels.
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. ©20230120
Please Recycle
AWMS-2-BT75-H
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>