ATDEC AWMS-2-LTH75-H Dual Vertical Heavy Duty Mount Installation Guide
- June 9, 2024
- ATDEC
Table of Contents
Installation Guide
AWMS-2-LTH75-H
Dual Vertical Heavy Duty Mount with
Heavy Duty F Clamp
COMPONENT CHECKLIST
AWM-FH
Heavy Duty F Clamp (x1)|
---|---
AWM-P75G
750 Post with Guide Marks (x1)|
AWM-LC
Channel Clamp (x2)|
AWM-LTH
Heavy Duty Tilt Head (x2)|
RANGE REQUIRED TOOLS
• Phillips Head Screwdriver
IMPORTANT INFORMATION
- Please ensure this product is installed as per these installation instructions.
- Do not remove/ throw away the plastic cap on channel clamp.
- This product is compatible with Atdec AWM Series products.
- Curved monitors, deep devices (such as all-in-one PCs) and offset VESA locations exert additional leverage that can exceed the capacity of the mount even though the monitor weight may be within the stated range.
- The manufacturer accepts no responsibility for incorrect installation.
Heavy Duty F Clamp
COMPONENT CHECKLIST 
-
Attach post to upper clamp
NOTE: Post packaged separately -
Attach lower clamp to upper clamp
2.1 Measure the worksurface thickness and choose the suitable lower clamp position
2.2 Attach lower
clamp to upper clamp in the suitable position using the two provided screws
NOTE: If there is only a
small gap behind the worksurface, perform Step 3.1 before this step. -
Fit fixing to work surface
3.1 Place in desired location on worksurface
3.2 Screw in both pressure plates and tighten evenly and
firmly
-
Post
COMPONENT CHECKLIST 
-
Attach Post to Fixing
1.1 Follow the Heavy Duty F Clamp installation guide on pages 2 of this booklet or provided with your alternate fixing option.
Supplied Heavy Duty F Clamp AWM-FH
Also Compatible Grommet Clamp AC-GC -
Mount Clamp to Post
2.1 Slide clamp into post and position to desired height. Turn knob to lock in place.
If you are installing multiple mounts, use the guide marks on post as reference for setting the height of each arm. Final fine-tuning may be required once monitor is installed.
NOTE: Guide marks only available on 400 post, 510 post and 750 post.
2.2 Do not mount monitor arm on
rear channel post when using the supplied Heavy Duty F Clamp
-
Position Cable Cover and fit Post Cap
3.1 To reposition the cable cover, pull it straight up and out of the post and insert it into any of the available channels
Optional cable cover positions
3.2 Fit post cap onto the top
of the post
-
Cable clips and cover
4.1 Push the cable down into the cable clip.
4.2 Insert one side of the cable
clip into the channel on the post assembly, then push in the other side.
4.3 Loop cable and insert into
cable cover.
4.4 Feed remaining cable into the
cover.
-
Channel Clamp
COMPONENT CHECKLIST
WEIGHT RANGE
0 – 14kg
(0 – 31lbs)
NOTE: Do not remove/throw away plastic cap on channel clamp.
-
Fix Clamp to Post
1.1 Ensure knob is undone.
1.2 Slide Channel Clamp into channel.
1.3 Hold clamp in desired position
on post and turn knob to lock in place.
-
(Optional) Set arm rotation to 180°
NOTE: default arm rotation is set to rotate 360# in the desired postion
2.1 Remove plastic sleeve2.2 Remove
rotation ring
2.3 Place
rotation ring in the desired position and replace plastic sleeve.
NOTE: Place the rotation
ring depending on what post channel the arm will be attached to. The tag
should always face towards the user.
Heavy Duty VESA Tilt Head
COMPONENT CHECKLIST 
WEIGHT RANGE
Flat Monitors
0 – 14kg
(0 – 31lbs)
Curved Monitors
0 – 12kg
(0 – 26.5lbs)
Monitor weight should be within the weight range of all modular elements that
make up the complete monitor mounting solution.
-
(Optional) Lock monitor rotation
OPTIONAL To lock monitor rotation screw the four M5x16 screws into the four holes on the front of the VESA Head. 1.1 Ensure VESA Plate is in this orientation before installing screws.
1.2 Install the four
Rotation Security Screws (G) into the front of the VESA Head
-
Attach VESA head to monitor NOTE: Spacers may be required for curved, recessed or uneven monitor surfaces.
2.2 Ensure suitable screw size is used.
2.3 VESA
mounting **compatibility NOTE:** For other sizes, use a suitable adaptor plate
-
Mount monitor onto Channel Clamp
3.1 Push tilt head onto the shaft at the end of the channel clamp, grub screw must be backed off at this time
NOTE: Ensure plastic sleeve is on shaft before fitting tilt head.
3.2 Ensure tilt head is fully pushed onto shaft.
3.3 Tighten the joint screw with 4mm allen key to secure
the tilt head and monitor in place. NOTE: Check the head pan adjustment is
smooth after tightening. -
Adjust tilt tension
4.1 Use the knob to tighten and loosen the tilt tension to suit your monitor weight.
NOTE: Always support the monitor whilst adjusting to prevent it from falling forward sharply.
IMPORTANT
If extra tilt tension is required for your monitor, use 4mm allen key to tighten second tilt screw. -
(Optional) Adjust rotation tension
NOTE: In most cases, monitor will balance in a level position with factory settings. If it droops to one side follow these steps to adjust the rotation tension.
5.1 Remove VESA head from monitor.
5.2 Tighten the two screws on the front of
the VESA plate using 4mm allen key.
5.3 Re-attach VESA head to monitor as per Step
1.
-
No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. ©20220321
**** Please Recycle
AWM-2-LTH75-H Page 6 of 6
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>