ATDEC AW-ORA-F Ora Mounting Arm for Monitor Installation Guide

ATDEC AW-ORA-F Ora Mounting Arm for Monitor

COMPONENT CHECKLIST

Hardware & Tools

• M4x10 Screw (x4)

• Security Screw (x1)

• 4mm Hex Key (x1)

CAPACITY

Weight: 2 – 8kg (4.4 – 17.6lb)
Display Size: Up to 35” (curved or flat) (Larger monitors within the weight capacity may be compatible, please contact Atdec for advice).

WARRANTY

10 Years Limited

TOOLS REQUIRED

Phillips head screwdriver

IMPORTANT INFORMATION

• Install Ora Monitor Arm as per these installation instructions.
• The manufacturer accepts no responsibility for incorrect installation.
• Do not over-tighten screws and adjustment points on product.
• This product is not suitable for outdoor use.
• Do not use this product for mobile applications.
• Please ensure desk structure and mounting surface are of sufficient strength to support this product and mounted equipment.
• Deep devices (such as all-in-one PCs), VESA mounted accessories (such as mini PC brackets and mounts), and offset VESA locations exert additional leverage that can exceed the capacity of the mount even though the monitor weight may be within the stated range. Please contact Atdec if you would like further information.
• Suits displays with VESA mounting hole patterns 75×75 and 100×100. Spacer kit (sold separately) may be required for recessed 75×75 hole patterns.
• For edge clamp Installations, ensure the monitor is always positioned over the work surface. Do not position the monitor beyond the rear edge of the work surface.
• Periodic adjustment to counterbalance and tilt tension may be required.

No portion of this document or any artwork contained herein should be reproduced in any way without the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. ©20230210

 Alternative Fixing Options

Ora Bolt Through Fixing AW-FB
(sold separately)

Attach F-clamp to Desk

Configure F Clamp for desk thickness

Position clamp on edge of work surface

TIP
When positioning the desk clamp, offset the clamp to the left or right of the seating position.
The monitor will then be centred for the user.

IMPORTANT
Ensure clamp is pushed up against work surface edge

Tighten firmly by hand or using 4mm hex key

HINT!

If the gap behind the work surface is less than 70mm (2¾”), unhook the lower bracket and reattach it from under the desk.

Hook on lower bracket and re-tighten 2x screws

Attach Lower Link to Clamp

NOTE
Pivot lower link to the forward position shown in Step 2.2 before selecting 180˚ rotation.

Attach Upper Link

IMPORTANT Ensure plastic sleeve is fitted on lower link

Press down firmly to ensure the upper link is fully located onto the lower link

Using the 4mm hex key, tighten set screw until joint rotation is firm and smooth

Check Cover Strip
To inspect cover strip, fully lower the upper link . If damaged or missing, stop installation and contact Atdec for assistance.

Mount Monitor

Check VESA mounting compatibility of monitor

Attach VESA Plate using supplied M4x10 screws.

Attach monitor to arm

Adjustments

Tilt Tension

If required, adjust tilt tension using 4mm hex key. (do not over-tighten)

NOTE Support the screen while adjusting

Monitor Rotation Tension (optional)

Adjust rotation tension using 4mm hex key.

NOTE
Adjustment may only be required for ultrawide monitors

Counterbalance Adjustment

Using the 4mm hex key, adjust counterbalance to suit the monitor weight

TIP
When installing multiple arms with the same monitor, use the setting on the counterbalance adjustment gauge to quickly ‘pre-set’ other arms (fine-tuning may be required after pre-setting)

Security Screw (optional)

If desired, once monitor is attached to the arm, install the security screw. This disables the release switch, preventing theft.

Removing Monitor

Positioning

Do not position monitor beyond the rear edge of the desk.

Cable Management

Overview

NOTE
Allow 1.2m of cable from the work surface to the monitor. Add additional cable length to route the cable from the work surface to the computer.

If desired, store hex key in lower link

Route Cables Through Upper Link

Remove lower link cable cover.

Tuck cables behind tabs inside lower link.

Re-attach lower link cable cover.

NOTE
Ensure cables do not interfere with sliding cover on.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>