HARVEST TEC 735Z Automatic Preservative Applicator Installation Guide

August 30, 2024
HARVEST TEC

735Z Automatic Preservative Applicator

Product Information

Specifications

  • Model: 735Z
  • Type: Automatic Preservative Applicator
  • Capacity: 55 Gallons
  • Installation Manual: 735Z-24-INST-Imp&Metric
  • Tools Needed: Standard socket set, Side cutter, Crescent
    wrench, Metal drilling and cutting tools, Standard screwdriver or
    5/16 nut driver, Hose cutter, Hammer, Center Punch

Product Usage Instructions

Installation of Applicator

  1. Using a lift, bring the assembly up under the cab of the
    baler.

  2. Ensure part 001-4703ZR-D2 aligns with the holes in the front
    part of the baler.

  3. Mark the half-inch holes at the ends of parts 001-4703ZR-A and
    001-4703ZR-B that align with the structural parts under the
    cab.

  4. Lower the assembly out of the way and drill these four holes
    with a 9/16 drill bit. Be cautious not to drill into hydraulic
    lines or electrical wires.

Mount Pump Plate Assembly

  1. Using two 3/8 x 1/4 bolts, locks, washers, and nuts, mount the
    U-shaped pump plate mount 001-4647 onto the tank saddle in the
    mounting holes located between the strap brackets on the back of
    the saddle.

  2. Connect the pump plate mounting bracket (001-4648X) using two
    3/8 x 1 1/4 bolts, nuts, locks, and flat washers to the mounting
    bracket.

  3. Install the pump plate as shown in the provided figures.

Installation of Plumbing

Details on plumbing installation are not provided in the
extracted text. Please refer to the complete user manual for
plumbing installation instructions.

Installation of Moisture Sensing Pads

  1. If your baler is equipped with bale shaping pads, remove the
    disc and use existing ones that will need to be drilled to 3/4
    (19mm) to install new moisture sensing discs.

  2. If your baler is not equipped with bale shaping pads, drill a
    hole in the chamber directly behind and above the starting
    roll.

  3. Place a plastic pad as a template for mounting the moisture
    sensing discs.

  4. Trim the bolt if necessary for proper fit.

  5. Tighten all hardware to 50 ft/lbs (68 N/m) and ensure the
    plastic pad protects all metal surfaces of the disc from touching
    the baler.

  6. Run the moisture wire harness from the pump plate area to each
    disc and secure it.

FAQ

Q: Can I use this applicator with any type of

preservative?

A: The applicator is designed to work with specific types of
preservatives. Please refer to the product specifications for
compatibility details.

Q: How often should I refill the tank?

A: The frequency of tank refills depends on your usage and
application requirements. It is recommended to monitor the tank
level regularly and refill as needed to ensure continuous
operation.

Installation Manual
Model 735Z
55 Gallon Automatic Preservative Applicator

735Z-24-INST-Imp&Metric

3/24

1

2

Harvest Tec 735Z Table of Contents
Introduction Tools Needed Installation of Applicator
Installation of Mounting Brackets and Tank Mount Pump Plate Assembly Placement of Spray Nozzle Assembly Installation of Plumbing Installation of Moisture Sensing Pads End of Bale Sensor Tractor Set Up Display Options Wiring Diagram Pin Outs Parts Breakdown Base Kit Pump Assembly Control Box and Wiring Harnesses End of Bale Sensor 700 Solenoid Package Moisture Sensor Optional High Moisture Kit Parts Bag Packages & Hoses Spray Shield Optional iPad Display Kit Optional Android DisplayKit Optional HT VT Display Kit Warranty Statement

PAGE 3 3
4-10 4-5 6 7 7 8 9 10 11 12 13-15 16-26 16-17 18 19 19 20 21 21 22 23 24 25 26 27

Introduction
Congratulations and thank you for purchasing a Harvest Tec Model 735Z applicator. Please read this manual carefully to ensure correct steps are taken to attach the applicator to the baler. This applicator is designed to apply Harvest Tec buffered propionic acid. Use of alternative products may cause complications. Including inaccurate readings from the flow meter and damage to all parts. Resulting in the warranty being void. A parts break down for the applicator is located in the back of the manual.

Tools Needed

– Standard socket set

– Side cutter – Crescent wrench – Metal drilling and cutting tools

– Standard screw driver or 5/16″ – Hose cutter – Hammer

– Center Punch

nut driver

3

Installation of Applicator
Installation of Mounting Brackets and Tank
1. Locate parts 001-4703ZR-A, 001-4703ZR-B, two 001-4703ZR-C and four ¾” x 4 ½” bolts, lock washers and nut.
2. Line up 001-4703ZR-A and 001-4703ZR-B about 18 inches apart on the ground. Slide part 001-4703ZR-C into square mounts and secure with ¾” x 4 ½” bolts, locks, and nuts to holed in place. Note there are two sets of ¾” holes on the 001-4703ZR-C. Use the set that is about 18 inches apart.
3. Locate part 001-4703ZR-D1 and two ½” x 5 ½” bolts, locks, washers, and nuts. Bolt part 0014703ZR-D1 to the top of the two 001-4703ZR-C with this hardware.
4. Locate part 001-4703ZR-D2. Bolt to the front of 001-4703ZR-D1 with ½” x 3 ½” bolts, washers, locks, and nuts. Do not fully tighten down.
5. Using a lift, bring the assembly up under the cab of the baler. Part 001-4703ZR-D2 should line up with holes in the front part of the baler. Mark the half inch holes at the ends of the 0014703ZR-A and 001-4703ZR-B that line up with the structural parts under the cab. Lower assembly out of the way and drill these four holes with a 9/16″ drill bit. (Note. Do not drill into hydraulic lines or electrical wires.
6. Once holes have been drilled. Lift assembly back up under cab and attach to baler with four ½” x 3 ½” bolts, washers on both sides, locks, and nuts. ¾” hardware is provided if you would want to use this. However, part 001-4703ZR-A and 001-4703ZR-B will need to be drilled out for the ¾” bolts. The 001-4703ZR-D2 will attach to the front mount with ½” x 2″ bolts, washers on both sides, locks, and nut.
7. Attach two 001-4703ZR-E to each 001-4703ZR-C (one on each side) sticking out the front of the baler. Use ¾” x 4 ½” bolts, locks, nuts. Do not fully tighten down yet.
8. Attach 001-4703ZR-G to the 001-4703ZR-E at the height you desire to keep the tank about the windrow. Note the lower the take the closer it is to the windrow coming into the baler. The higher it will obstruct your view. Use ¾” x 4 ½” bolts, locks, and nuts to secure.
9. Attach 001-4703ZR-G to 001-4703ZR-F with ½” x 4″ Bolts, washers, locks, and nut. Do not fully tighten down. (Note: angles will be pointing toward each other.
10. Place saddle assembly on 001-4703ZR-G and secure with ½” washer, locks, and nuts. 11. Tighten all hardware down.
001-4703ZR-A

001-4703ZR-C

001-4703ZR-G

001-4703ZR-D2

001-4703ZR-B 001-4703ZR-D1
001-4703ZR-E

001-4703ZR-F
4

Installation of Mounting Brackets and Tank (continued)
5

Mount Pump Plate Assembly
Locate parts bag 8. Using two 3/8″ x 1/4″ bolts, locks, washers, and nuts. Mount the U-shaped pump plate mount 001-4647 (right) onto the tank saddle in the mounting holes located between the strap brackets on back of saddle (figure 7).
Connect the pump plate mounting bracket (001-4648X), shown in figure 8, using two 3/8″ x 1 1/4″ bolts, nuts, locks, and flat washers to the mounting bracket. Install the pump plate as shown completed in figure 9.

Figure 7

Figure 8

Figure 9

Figure 10

6

Placement of Spray Nozzle Assembly The cross bar on the wind guard above the pick-up head provides a mounting point for the nozzle holders (001-4714). Mount the nozzle holders on the wind guard, using the supplied U bolts (001-4714UBL). Measuring from the center of the baler, the nozzle holders will need to be 6″ (15cm) apart on a 4′ (1.2M) and 9″ (23cm) apart on a 5′ (1.5M) Do not fully tighten. Position the nozzle holders so that the tips spray in a horizontal direction over the top of the baler’s pickup. The tips should be located so that they will be between 14″ and 18″ (35 – 45 cm) from the normal path of hay. Make sure the nozzle holders do not interfere with the tying system. *It is recommended to test the system with water prior to field operation. This will ensure the fan pattern from the tips reaches the outside edges of the pickup while having a slight overlap in the center.
Installation of Plumbing A. Intake
Locate parts bag 16. Use the 003-EL3412 on the bottom of the tank to route 1/2″ line (002-9001) to the 003-A1212 or 003-EL1212 fitting used on the ball valve attached to the pump plate. Attach hose clamps (003-9003) on both of the fittings. B. Discharge Route the 1/2″ hose from the pump output toward the front of the baler and connect to the solenoid assembly (SOL-3SP-A). Secure the solenoid assembly and hose along baler, positioning the solenoid as close to the spray tips as possible while remaining in an accessible location. Connect the 1/4″ hose to the outgoing side of the solenoid to tip assembly. C. Low, Standard and High Output Tips Your baler comes standard with one set of tips. Optional High Output Tip kit 700RBHTK is available for increased application rates.
7

Installation of Moisture Sensing Pads *Most balers will have a moisture system already installed on the baler. If not, follow the instructions below. Note: If your baler does have a factory moisture system installed. You can use the factory moisture disc. However, you will need to disconnect the wires leading to both sensors and tape them up. You cannot have the balers moisture wires and Harvest Tec’s moisture wires connected to the moisture disc at the same time.
Figure 1

2″ from back of chamber
(51mm)

1″ from top of roll
(25mm)

1. If your baler is equipped with bale shaping pads, remove disc and use existing that will need to be drilled to 3/4″ (19mm) to install new moisture sensing discs. If the discs are welded, the welds will need to ground off for disc removal.
2. If your baler is not equipped with bale shaping pads you will need to drill a hole in the chamber directly behind and above the starting roll (Figure 1).
3. The mounting hole will be 3/4″ (19mm) in diameter. Use a plastic pad (006-4641F) and place it into the baler to use as a template. The bottom edge of the pad will be placed 1″ (25mm) up from starting roll and 2″ (51mm) from the back of the bale chamber. (Figure 1)

006-4641G

Moisture Harness
Loop

006-4641I

006-4641H

006-4641F
4. Depending on the baler the bolt may need to be trimmed for proper fit. 5. Tighten all of the hardware to 50 ft/lbs (68 N/m). 6. Make sure that the plastic pad is protecting all metal surfaces of the disc from touching baler. 7. Run the moisture wire harness (006-7307RB1) from pump plate area to each disc and secure
8. Apply silicone over nuts and washers.
8

Installation of End of Bale Sensor
The bale rate timer/ end of bale sensor is used to determine when the baler door is open upon bale completion. With this information the system is able to change the tons/hour automatically (see Operating Instructions, Automatic Mode).
Locate the sensor (006-7401) and the sensor bracket (001-4648RB). On the right side of the baler find a location 1″­ 6″ down from the pivot point, in a well- suited place, to mount the bracket. Check for clearance with hydraulic cylinders before mounting the bracket. The bracket should be mounted to the front side of the hinge point, with the sensor aligned over the back door.
Mark and drill two 1/4″ (7mm) holes and install the bracket using two 5/16″ x1/4″ self-tapping bolts.
Install the sensor into the bracket and leave 1/4″ (7mm) of clearance between the end of the sensor and the door.
The harness will need to be routed towards the Processor. Secure with cable ties and take care to avoid pinch points. The harness extension (006-7401EXT) may need to be used.

Hinge Point Back Door

006-7401 001-4648RB

View of the right side of

Front of baler

*Additional parts and harness extensions have been included to allow you to easily disconnect the baler unit from the power unit, use as needed.

9

Tractor Setup

The general tractor setup of the 700 Series applicator can be seen above. The main harness of interest is the tractor power/communication harness (006-765IC). This harness will connect at the tractor battery, to the ISO Communication Module (ICM) mounted in the cab, a keyed power connection point, and connect at the hitch area to the baler power/communication harness (006-765B). View below to see highlighted installation instruction:

12V Battery Connection

The 12V battery connection must be at the tractor battery. Connection to alternative locations such as an accessory port can cause problems with applicator system. MUST BE CONNECTED DIRECT TO TRACTOR BATTERY TERMINALS

The ISO communication module is to be mounted inside the cab. Other ISO Communication Module mounting locations can lead to issues with weathering and operation.
Once installed and the system is powered, a green light will turn on with
the ICM module.

Key Power Connection

Ensure a solid keyed connection is found inside the cab and wired into. Poor keyed power connection can result in applicator system issues.

Harness Connection to Baler

The tractor harness connects at the hitch to baler power/communication harness (006-765B). This will allow the system components to communicate with one another. Ensure connections are debris and corrosion free.

10

Display Options Optional Harvest Tec Display
The 700 series Harvest Tec Display will allow you to set your real time baling parameters to ensure the most precise application to every bale. This is done by utilizing the improved touch technology to select objects, enter data, and swipe through operational screens. The Harvest Tec Display offers easy integration by connecting to the additional CAN plug on the 006-765IC harness. Once, connected the Harvest Tec display will power up with applicator system. Note: The Harvest Tec Display must be used as a standalone display, the baler cannot run both integrated and on the Harvest Tec Display. Must be one or the other. Removal of the 006-765VA or integration harness is required when equipped. 006-770R Terminator must be placed on only one CAN/IDM port on the baler harness. Optional Tablet Display
Precision Baling App
The iOS or Android Tablet displays offer the ability to communicate with the 700 series applicator system via hard-wired connection to the ISO Communication Module (ICM). Recommended to use a quality communication cable to connect with the IIC- adapters are not supported. Through the free Precision Baling App, the operator can set real time baling parameters to ensure the most precise application to every bale. This provides a multi-use option while utilizing the improved app to select objects, enter data, and easily switch through operational screens. The Tablet Display offers easy integration by connecting a charging cable to the USB port on the ICM module. Once connected the Harvest Tec applicator will display upon opening the app and powering up the applicator system. Tablets can be used in addition to integrated baler VT display.
Required to be running a current supported iOS operating system. *iPad is a trademark of Apple Inc., registered in the U.S. and other countries.
11

Wiring Diagram ­ 731, 735Z, 737, 738K, 747, & 749 Models
1. Connect the power harness (006-765IC) to the tractor battery (12 volt) using the red wire with fuse to the positive side and the black wire to the negative. A. The power harness must be connected to the battery! CONTACT HARVEST TEC BEFORE MODIFICATIONS. The unit will draw more amps than convenience outlets can handle. Any modifications of the power harness will void systems warranty B. This unit will not function on positive ground tractors. C. If the unit loses power while operating it will not keep track of accumulated pounds of product used.
2. The power harness on the tractor (006-765IC) will run from the tractor battery to the hitch. The power harness on the baler (006-763B) will connect to the tractor power harness (006-765IC) at the hitch.
3. Connect the keyed power wire (006-765CPH) to a keyed power source on the tractor. The keyed power wire must connect to a keyed source or the unit will not power up correctly.
4. Attached the ISO Communication Module (006-6673) to the tractor power harness (006-765IC). 5. Attach the End of Bale (EOB) connection on baler harness (006-763B) to the EOB Sensor (006-7401). 6. Attach the Solenoid (SOL

  1. connections on the baler harness (006-763B) and to the solenoids (002-2203F). 7. Attach the Flowmeter (006-4724A) to the Pump Module connection on pump plate assembly. 8. Attach the rubber molded connector on pump plate to the Pump (007-4120DE). 9. Attach moisture disc harness (006-7307RB) connection to the IPM and connect to Moisture Discs 10. Ensure 006-700R terminator is connected to CAN/IDM port on 006-763B harness

Optional Harvest Tec Display Harness 006-765GH
Key Power Harness 006-765CPH
Power Harness on Tractor 006-765IC

ISO Communication Module (ICM) 030-6673

Optional Hay Indicator Harness
006-7503H

Optional Hay Indicators 006-7502(E / R)

Power Harness on Tractor 006-763B

Solenoids 002-2203F
Solenoid Harness* 006-3650-S1

End of Bale Extension 006-7401EXT

End of Bale Sensor 006-7401

006-700R terminator will cap CAN Port

*Second Solenoid and Harness used only with
Optional 700RBHTK High-Output Kit

700 ISO Pump Module (IPM)

006-7671RB

Flow Meter

006-4724A

Moisture Harness 006-7307RB

Moisture Disc (x2) 006-4641H or 006-4641HX

12

Pin Outs

Integrated Control Module (ICM) on Tractor Harness 006-765IC
(Deutsch Plug Number: DTM06-12SA)

Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 Pin 11 Pin 12

Red Purple Red/White Black/White Orange Blue Green Yellow White Gray Brown Black

+12V from ECU Signal Wire +12V CAN X Ground CAN X CAN X Hi CAN X Lo ISO CAN Lo ISO CAN Hi GPS Expansion 1 GPS Expansion 2 GPS Expansion 3 Ground from ECU

12 3456 12 11 10 9 8 7

ISOBUS Plug on Tractor Harness 006-765IC
(Deutsch Plug Number: DT04-4P)

Pin 1 Pin 2 Pin 3 Pin 4

Red Yellow Green Black

+12V from ECU ISO CAN Hi ISO CAN Lo Ground from ECU

1

3

2

4

Power / Communication Tractor Harness 006-765IC at Hitch
(Deutsch Plug Number: HDP24-24-18PN)

Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 Pin 11 Pin 12 Pin 13 Pin 14 Pin 15 Pin 16 Pin 17 Pin 18

Not Used Yellow Green Red Black Red Not Used Black Not Used Purple Red/White Black/White Orange Blue White Gray Brown Not Used

—ISO CAN Hi ISO CAN Lo +12V Power to ECU Ground to ECU +12V From Battery —Ground From Battery —Signal Wire +12V CAN X Ground CAN X CAN X Hi CAN X Lo GPS Expansion 1 GPS Expansion 2 GPS Expansion 3 —-

13

Pin Outs (continued)

Power / Communication Baler Harness 006-763B at Hitch
(Deutsch Plug Number: HDP26-24-18SN)

Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 Pin 11 Pin 12 Pin 13 Pin 14 Pin 15 Pin 16 Pin 17 Pin 18

Not Used Yellow Green Red Black Red Not Used Black Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used Not Used

—ISO CAN Hi ISO CAN Lo +12V Power to ECU Ground to ECU +12V From Battery —Ground From Battery ——————————-

Power / Communication Baler Harness 006-763B at IPM Module
(Deutsch Plug Number: HDP24-24-18PN)

Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 Pin 11 Pin 12 Pin 13 Pin 14 Pin 15 Pin 16 Pin 17 Pin 18

Not Used Yellow Green Red Black Red Not Used Black Not Used Orange/White Orange/Black Purple/Green Blue/White Gray/Red White/Black Orange/Red White/Black Not Used

—ISO CAN Hi ISO CAN Lo +12V Power to ECU Ground to ECU +12V From Battery —Ground From Battery —+12V Power to EOR Ground to EOR EOR Signal EOB Signal +12V Power to Solenoid 1 Ground to Solenoid 1 +12V Power to Solenoid 2 Ground to Solenoid 2 —-

*IPM Module Whip Plug- Pin # 5 Not Used

Solenoid 1 Plug on Baler Harness 006-763B
(Deutsch Plug Number: APTIV 12052641)

Pin B Pin A

Gray/Red White/Black

+12V to Solenoid 1 Ground to Solenoid 1

Solenoid 2 Plug on Baler Harness 006-763B
(Deutsch Plug Number: APTIV 12052641)

Pin B Pin A

Orange/Red White/Black

+12V to Solenoid 2 Ground to Solenoid 2

14

A

B

Pin Outs (continued)

CAN / IDM on Baler Harness 006-763B
(Deutsch Plug Number: DT06-4S)

Pin 1 Pin 2 Pin 3 Pin 4

Red Yellow Green Black

+12V to ECU ISO CAN Hi ISO CAN Lo Ground to ECU

End of Bale Sensor Plug on Baler Harness 006-763B
(Deutsch Plug Number: DT06-3S)

Pin 1 Pin 2 Pin 3

Orange/White Orange/Black Blue/White

+12V to End of Bale Sensors Ground to End of Bale Sensors Signal

End of Row Sensors Plug on Baler Harness 006-763B
(Deutsch Plug Number: DT06-3S)

Pin 1 Pin 2 Pin 3

Orange/White Orange/Black Purple/Green

+12V to End of Bale Sensors Ground to End of Bale Sensors Signal

Pump Connection on 700 Controller Harness
(16 AWG Two-Wire Plug)
Pin 1 Red Power to Pump Pin 2 Black Ground to Pump

1

3

2

4

1

2

3

Pin 2

Pin 1

15

Model 735Z Base Kit

1

2

4

3

Ref Description

Part #

Qty Ref Description

1 50 Gallon Tank

005-9203SQ 1 7 Side Rail Plate

2 Tank Cap, Gasket, & Breather P05-9022HBG 1 8 Front Mount Support

3 Tank Saddle

001-4703X

1 9 Front Mount Crossmember

4 Tank Strap

001-4402

2 10 Long Side Rail

5 Tank Saddle Support

001-4703ZE-G 2 11 Mid Mount

6 Short Side Rail

001-4703ZR-F 2 12 Rear Mount

NP Hex Plug

Complete Kit

Part #

Qty

001-4703ZR-E

4

001-4703ZR-D2 1

001-4703ZR-D1 1

001-4703ZR-C

2

001-4703ZR-B

1

001-4703ZR-A

1

003-F34

1

030-0445Z-TK

16

Model 35Z
Base Kit (continued)
12 11
10 8
9 7
6 5

Ref Description

Part #

Qty Ref Description

1 50 Gallon Tank

005-9203SQ 1 7 Side Rail Plate

2 Tank Cap, Gasket, & Breather P05-9022HBG 1 8 Front Mount Support

3 Tank Saddle

001-4703X

1 9 Front Mount Crossmember

4 Tank Strap

001-4402

2 10 Long Side Rail

5 Tank Saddle Support

001-4703ZE-G 2 11 Mid Mount

6 Short Side Rail

001-4703ZR-F 2 12 Rear Mount

NP Hex Plug

Complete Kit

Part #

Qty

001-4703ZR-E

4

001-4703ZR-D2 1

001-4703ZR-D1 1

001-4703ZR-C

2

001-4703ZR-B

1

001-4703ZR-A

1

003-F34

1

030-0445Z-TK

17

Parts Breakdown for Pump Assembly
006-4724A

001-4647

Part#
003-EL3812 007-4120DE 003-M3838 003-SE38 002-4566F 003-RB3814PB 006-4724A 003-RB1214PB 003-M1212F

Description

Qty Part#

Description

Qty

3/8″MPT X 1/2″HB Elbow 1

003-M1212

1/2″ Union

2

300 Series Pump

1

002-4315-100 1/2″ Line Strainer-100 Mesh 1

3/8″ x 3/8″ Union

1

003-SE12

1/2″ Street Elbow

1

3/8″ Street Elbow

1

002-2212

1/2″ Ball Valve

1

3/8″ Check Valve

1

003-EL1212 1/2″MPT x 1/2″HB

1

RB 3/8″ x 1/4″ Reducer

1

001-4648XL 300 Pump Support

1

Flow Meter ­ Deutsch Plug 1

001-4648X

Pump Plate Mount

1

RB 1/2″ x 1/4″ Reducer

1

003-A1212

Not Pictured

1/2″ Coupler

1

003-A3812

Not Pictured

Pump Assembly PMP-7636P (001-4647 Not Included)

Completed Assembly

*Note: Due to alternative baler designs, elbow 003-EL3812 can be replaced by straight fitting 003-A3812. As well as elbow 003-EL1212 can be replaced by straight fitting 003-A1212. Both straight fittings are included.
18

Control Box and Wiring Harnesses
1 2
2

3

5

4

Ref Description

Part#

Qty

1 Power Lead Baler 20′ 006-762B

1

2 Power Lead Tractor 006-765IC

1

3 Key Switch Wire

006-765CPH 1

4 ISO Pump Module 006-7671RB 1

5 ISO Communication 006-6673

1

Module

Ref Description
NP 120 Ohn Resistor NP Dust Plug Kit NP Lightning to USB-A Cable NP Optional USB-C to USB-A
Communication Cable

Part#

Qty

006-700R*

1

006-765DP

1

006-6672USBC 1

006-6672USBX 1

*006-700R installation on 006-762B harness is required at all times when operating the small square 700 series applicator

End of Bale Sensor

2
1 3

Ref Description

Part #

Qty

1 End of Bale Sensor 006-7401

1

2 EOB Extension

006-7401EXT 1

3 End of Bale Bracket 001-4648RB 1

Complete Assembly

EOB-7RB-A

19

700 Pulsing Solenoid- Round Balers
1A, 1B, or 1C

2

3

4 5

6

7
10
8 9

Ref Description 1A Solenoid Harness (5′) 1B Solenoid Harness (10′) 1C Solenoid Harness (15′) 2 #6 Hose Clamp 3 1/4″x1/2″ Straight Fitting 4 1/4″ Female Connector 5 Rubber Washer

Solenoid Packages

Part #

Qty Ref Description

006-3650-S1

6 1/4″ Female Disconnect

006-3650-S2

7 Solenoid

006-3650-S3

8 Solenoid Valve Body

003-9003

1

9 1/4″ x 1/4″ Straight Fitting

003-A1412

1

10 Mini Hose Clamp

004-1207G

1

004-1207W 2

Complete Assembly Pkg. A

Complete Assembly Pkg. B

Complete Assembly Pkg. C

Part #

Qty

004-1207H 2

002-2203F 1

004-1207VF 1

003-A1414 1

003-9002

1

SOL-3SP-A SOL-3SP-B SOL-3SP-C

Expanded View of Pulsing Solenoid (002-2203F)
Replacement Pulsing Solenoid O-Ring Kit available (002-2203FG) (Includes EPDM O-Rings 6, 8, 9 shown below)

To clean solenoid valves: The Center Section can be removed from Housing #2 by loosening #1 from #3. Once removed, use wrenches on components #3 and #7 and gently turn to loosen and separate. Soak parts #3-10 in warm soapy water, clean with a soft bristle brush, rinse with clean water to remove buildup before reassembly.
20

OPTIONAL High Output Solenoid
(Included with 700RBHTK Kit)

12 13 14 15

16 17 18

19 20

21 22

Ref Description

Part #

Qty

12 #6 Hose Clamp

003-9003

2

13 1/4″ x 1/2″ Straight Fitting 003-A1412

2

14 Female Quick Coupler

004-1207H

2

15 Rubber Washer

004-1207W

1

16 Solenoid

002-2203F

1

17 Solenoid Harness (10′)

006-3650-S2

1

18 1/4″ Street Elbow

003-SE14

1

19 Mini Hose Clamp

003-9002

1

20 1/4″ x 1/4″ Straight Fitting 003-A1414

1

21 Solenoid Check Valve

004-1207VF

2

22 1/4″ Tee

003-TT14

1

Moisture Sensors Parts Breakdown

1

2

6

Ref Description Part #

Qty

1 Plastic Pad

006-4641F 2

2 Moisture Disc 006-4641H 2

3 Plastic Bushing 006-4641G 2

3

5

4

Ref Description 4 Plastic Isolator 5 1/2X4 1/2″ Carriage Bolt 6 Moisture Cable (both15′)

Part #

Qty

006-4641I

2

2

006-7307RB1 1

Moisture Pad Assembly (Ref 1-5) 030-4643

2

Complete Assembly (Ref 1-6)

MSH-7RB-A

21

Parts Bag Packages & Hoses

PBA-1

PBP-16

1

5

10

12

8

6 2

9
3 7
4

Ref Description

Part #

Qty

1 3/4″ Ball Valve

002-2200

1

2 Valve Holder

001-6702H

1

3 Female Coupler

002-2204A

1

4 Male Shut-Off Plug

002-2205G

1

5 3/4″ x 3/4″ Elbow

003-EL3434

1

6 #10 Hose Clamp

003-9004

2

7 3/4″ x 3/4″ Straight

003-A3434

1

Fitting

8 Valve Decal

DCL-8004

1

9 Chemical Hazard Decal DCL-8001

1

Complete Drain Fill Kit 030-0493DFK

11

13

Ref Description 10 3/4″ x 1/2″ Elbow 11 3/4″ Jiffy Clip 12 #6 Hose Clamp 13 Small Jiffy Clip

Part #

Qty

003-EL3412 1

008-9010

3

003-9003

1

008-9009

3

Hoses

11

12

13

Ref Description

Part #

Qty

11

1/2″ Hose (Tank to Solenoid)

002-9001

15ft

12

3/4″ Hose (Drain/Fill Line)

002-9002 6ft

13 1/4″ Hose

002-9016 6ft

(Solenoid to Tips)

.
22

2

3

1

735Z Spray Shield
5 4
6

7 8

9

10

12

11

13

Ref Description 1 U Bolt 2 Hose Clamp 3 1/4″ x 1/4″ Fitting 4 1/4″ Sq Tee 5 1/4″ St Elbow 6 Oetiker Clamp 7 Nozzle Holder 8 Hose 9 1/4″ x 1/4″ Fitting

Part #

Qty

001-4714UBS 4

003-9002

2

003-A1414

5

003-TT14SQ 1

003-SE14F

1

003-9008

4

001-4714J

2

002-9016

3ft

003-A1414F 2

Ref Description 10 Nozzle Body 11 Tip Strainer 12 Tip ­ Gray* 13 Nozzle Cap NP 477 Jiffy Clip

Part #

Qty

004-4722

2

004-1203-100

2

004-XR11006VS 2

004-4723

2

008-9014

2

  • Tip color subject to change

Spray Shield Only

030-4714J-SO

23

Optional iPad Display Kit

1

3 2

4

9

6

7

8

5

Ref Description

Part #

Qty

1 iPad Mini 4 (Refurbished) 006-4670IP

1

2 Suction Cup Mount

001-2012SCM 1

3 Ram Mount

001-2012H

1

4 Spring Load Cradle

001-2012SLC

1

5 iPad Mini 4 Case

001-2012C4

1

NP Lightning Comm. Cable 006-6672USBC 1

6 Power Harness

006-4723P

1

NP 4 amp Fuse

Hardware

1

7 Female Spade Connector Hardware

2

8 Eye Loop Connector

Hardware

2

9 iPad Mini Charger 12V 001-2012P

1

Complete iPad Mini Kit

030-4670DK

(Includes 1-5 and Comm. Cable)

Mounting Kit Only

030-2014MK

(Includes all parts except iPad Mini 4)

12V Power Harness Installation Instructions (included with Mounting Kit Only)
1. Identify 12V power source for wires to connect. 2. Eye loops installed on harness if wiring directly to the battery is desired. 3. Test for key power source if preferred to have power to the USB shut off with the key. 4. Once power source is identified, cut wires to desired length if needed for key power connection. 5. Harness comes with quick connectors the white and black wires. 6. Remove the round locking plastic nut from USB plug before connecting the wires. Black (+) White (-). 7. The wires will then be hooked to the designated terminals on the bottom of the USB plug 8. Drill a 1 1/8″ hole in the preferred mounting location. Be sure to clean any sharp edges after drilling. 9. Feed the wires through the mounting hole. 10. If using the round plastic nut to secure plug in place, slide the nut back over the wiring before connecting
the wires to powered source. 11. Connect the wires to the identified power source if easier to do so before tightening the plug into place. 12. Tighten plug using either the round plastic nut or mounting plate and two screws, both options supplied. 13. Once connected, hook a USB charging cord into the plug and connect a mobile device/tablet to ensure
the plug is operating as you wish (key power working properly if necessary). NOTE: This plug is not designed to charge two iPads. System damage could occur if this is attempted.
System will charge a mobile phone and iPad simultaneously without problem.

*iPad mini is a trademark of Apple Inc., registered in the U.S. and other countries.

24

Optional Android Display Kit (030-1670DK)
5
3 1

4 2

Ref Description

Part #

Qty

1 Suction Cup Mount 001-2012SCM 1

2 Ram Mount

001-2012H

1

3 Spring Load Cradle 001-2012SLC

1

4 Android Case

001-2012A1

1

5 Android Tablet

006-1670AT

1

Installation Instructions 1. Assemble Cradle (001-2012SLC) 2. Attach round base from ram mount to cradle 3. Attach trapezoid end of ram mount to suction mount 4. Clean glass or metal surface that unit will be attaching to. 5. Add a small amount of water to suction cups rubber surface and attach to surface 6. Turn lock on suction cup mount to secure. 7. Place tablet in cradle and hook USB cable that came with system into it. 8. Run USB cable over to (006-765ICM) control module and plug into USB port that show’s a tablet

25

Optional Harvest Tec Display Kit (030-7670DK)
3

4
1 5
2

Ref Description 1 Suction Cup Mount 2 Ram Mount 3 Harvest Tec Display 4 Display Harness 5 Mounting Plate NP 700 Series Resistor

Part #

Qty

001-2012SCM

1

001-2012H

1

006-765GVT

1

006-765GH

1

001-700GH

1

006-700R

1

Installation Instructions
1. Identify 006-765GH harness connection to 006-765IC tractor harness. 2. Connect harness to the Harvest Tec Display before tightening into place. 3. Tighten the mounting and display. Streamline harness, as necessary. 4. Once connected, power cycle system and ensure display is working properly.
NOTE: CANNOT OPERATE WITH BOTH HARVEST TEC DISPLAY AND BALER VT CONNECTED AT THE
SAME TIME.

26

Harvest Tec LLC. Warranty and Liability Agreement
Harvest Tec, LLC. will repair or replace components that are found to be defective within 12 months from the date of manufacture. Under no circumstances does this warranty cover any components which in the opinion of Harvest Tec, LLC. have been subjected to negligent use, misuse, alteration, accident, or if repairs have been made with parts other than those manufactured and obtainable from Harvest Tec, LLC. Our obligation under this warranty is limited to repairing or replacing free of charge to the original purchaser any part that in our judgment shows evidence of defective or improper workmanship, provided the part is returned to Harvest Tec, LLC. within 30 days of the failure. If it is determined that a non-Harvest Tec branded hay preservative has been used inside the Harvest Tec applicator system where the failure occurred, then Harvest Tec reserves the right to deny the warranty request at their discretion. Parts must be returned through the selling dealer and distributor, transportation charges prepaid. This warranty shall not be interpreted to render Harvest Tec, LLC. liable for injury or damages of any kind, direct, consequential, or contingent, to persons or property. Furthermore, this warranty does not extend to loss of crop, losses caused by delays or any expense prospective profits or for any other reason. Harvest Tec, LLC. shall not be liable for any recovery greater in amount than the cost or repair of defects in workmanship. There are no warranties, either expressed or implied, of merchantability or fitness for particular purpose intended or fitness for any other reason. This warranty cannot guarantee that existing conditions beyond the control of Harvest Tec, LLC. will not affect our ability to obtain materials or manufacture necessary replacement parts. Harvest Tec, LLC. reserves the right to make design changes, improve design, or change specifications, at any time without any contingent obligation to purchasers of machines and parts previously sold. Revised 4/17
27

HARVEST TEC, LLC. P.O. BOX 63
2821 HARVEY STREET HUDSON, WI 54016 USA
PHONE: 715-386-9100 FAX: 715-381-1792
Email: info@harvesttec.com
28

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

HARVEST TEC User Manuals

Related Manuals