Eventide V12 Micro Pitch User Guide
- June 6, 2024
- Eventide
Table of Contents
Eventide V12 Micro Pitch Delay User Guide
Knob Functions – Secondary Parameters
Expression Pedal
Morphing from Heel to Toe
An Expression Pedal can be used to change any grouping of knob Parameters in one smooth gesture. Programming an Expression Pedal is easy. You simply need to set end points for Heel & Toe. Here’s how:
- Press Pedal fully Heel down.
- Adjust any combination of the Parameter control knobs.
- Press Pedal fully Toe down.
- Adjust any combination of the Parameter control knobs.
- Save it or lose it. See “Saving a Preset.”
Clear Expression Pedal Mappings
To clear the Expression Pedal mappings for the knobs, hold the ACTIVE Footswitch and, while holding, press the ACTIVE Button until the Preset Ladder LEDs flash twice.
Note: To use an Expression Pedal, the Exp Pdl Jack must be set to either [EXP] or [EXP + AUX]. See System Setup to select.
MIDI Messages
Save Preset
Enter Save Mode by pressing and holding the TAP Button, then a MIDI program change message will save a Preset to the Preset Slot of the given value 1-127.
Load Preset
MIDI program change message loads the Preset from the Preset Slot of the given
value 1-127.
Note: The bottom two Ladder LEDs will be lit when Presets 6–127 are selected
via MIDI or Device Manager.
Receive/send using the USB Port or Exp Pdl Jack*.
CC 4: Expression Pedal
CC 9: TAP TEMPO
CC 14: ACTIVE/BYPASS (>=64 is Active)
CC 15: FLEX (doubles Pitch A & B, >=64 is ON)
Parameters: CC Messages Map
*Use a MIDI Converter Box or a DIN to TRS or TRS cable
System Setup
Enter System Setup
To access these Global Settings, apply power while holding ACTIVE Footswitch
and button.
Top two LEDs light when in System Setup. Changes are stored as they are
made. Cycle power to exit System Setup.
Set MIDI Channel
Set MIDI Clock
Set Bypass Mode
Catch Up ON/OFF
Set Exp Pdl Jack
[EXP+AUX (Momentary)]
TIP = Expression Pedal
RING = FLEX (doubles Pitch A & B)
[TRIPLE AUX]
TIP = Increment Preset
RING = Decrement Preset
TIP + RING = Load Preset
Note: Times out after a few seconds
[MIDI BOX]
Receive and Send MIDI via a MIDI Converter Box (Tip Active)
[MIDI TRS]
Receive MIDI directly with a DIN to TRS or TRS cable.
Presets – 5 On Board, 127 Via MIDI
The currently loaded Preset is indicated on the Preset LED Ladder. When a Preset is modified the Preset LED blinks once.
Load Presets
To select and load a Preset using Footswitches:
- TAP Footswitch selects Preset 1 to 5. Preset 1 (top LED) to Preset 5 (bottom LED) blinks.
- ACTIVE Footswitch loads the Preset. LED stops blinking.
NOTE: To select Preset, TAP Footswitch must be in Preset mode. If TAP LED is lit, press and hold TAP Footswitch.
Save Presets
To save one of the 5 Presets using the Buttons:
- Press & hold TAP Button
- Blinking Ladder and Button LEDs let you know you have entered Save Mode.
- TAP Button selects Preset 1 to Preset 5.
- ACTIVE Button saves Preset
- LEDs stop blinking to let you know the Preset is saved.
NOTE: Save Mode times out after a few seconds. Pressing either Footswitch exits Save Mode.
- LEDs stop blinking to let you know the Preset is saved.
Catch Up Knob Function
When a Preset is loaded or when toggling between Parameters using , Knob positions will not align with their current Parameter values. As a result, turning a knob will likely cause an abrupt change in the sound.
With Catch Up ON, the sound does not change until the Knob is moved to the position corresponding to the current value. The LED Ladder indicates whether the knob must be turned CCW (top LED blinks) or CW (bottom LED blinks). The LED flashes more rapidly as the knob approaches the value set by the Preset. All five LEDs blink once when the knob matches the stored Parameter value.
Note: To enable/disable Catch Up Knob Function, power up in System Setup mode and press TAP Footswitch to toggle ON/OFF.
TAP Footswitch Functionality
Press & Hold the TAP Footswitch to toggle between Tap mode and Preset Select mode.
Press the TAP Button/LED to toggle between Tap Time and Tap Tempo as follows:
Device Manager Software
Available from Eventide’s website for Mac & PC
- Update Pedal Firmware
- Restore Factory Settings
- Import/Export Presets
- Backup/Restore entire device to a file
- Edit System Settings
- View, edit, and organize Presets
Download: eventideaudio.com/edm
Restore Factory Settings: Boot pressing ACTIVE Footswitch & ACTIVE Button
Software Update: Boot pressing TAP Button & TAP Footswitch
Instructional Videos
eventideaudio.com/MicroPitchDelay
Technical Support
eventideaudio.com/support
Follow us on Social
MicroPitch Delay Quick Reference Guide for Firmware v1.0+| Eventide Part#
141347 Rev A
Eventide is a registered trademark of Eventide Inc. © 2021 Eventide Inc.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>