HARVEST TEC 347C 55 Gallon Preservative Applicators Instruction Manual

Installation Manual
Model 347C
55 gallon Preservative Applicators
Equipment and Products for Quality Hay.™

347C 55 Gallon Preservative Applicators

DECLARATION OF INCORPORATION MANUFACTURER:
Harvest Tec LLC.
2821 Harvey St.
P.O. Box 63
Hudson, WI 54016, U.S.A.
REPRESENTATIVE ESTABLISHED IN COMMUNITY:
Profitable Farming Company
Middle Barlington, Roborough
Winkleigh, Devon, EX19 8AG
ENGLAND
The person above certifies and declares that:
VIRTUAL MACHINE: Equipment mounted on a farm press and for the application of innoculants onto forage crops.
MODEL: 347C-17-INST-Imp&Metric
BRAND: Harvest Tec
SERIAL NUMBER:
This application preservatives for hay Harvest Tec system meets the Directive 2006/42/EC of the European Parliment and the Council of 17 May 2006 and other applicable European Directives including Directive 2004/108/EC on the Electromagnetic compatability.
The application of preservatives for hay Harvest Tec system will be turned on after being installed on a farm press has been declard in conformity with the Machinery Directive.
Person in the community authorized to provide information on the partly completed machinery and making this statement:
Richard Snell, President, Profitable Farming Company
Signed on May 21, 2011: Middle Barlington, Roborough
Winkleigh, Devon, EX19 8AG
ENGLAND

Introduction

Congratulations and thank you for purchasing a Harvest Tec Model 347C applicator. Please read this manual carefully to ensure correct steps are taken to attach the applicator to the baler. This applicator is designed to apply Harvest Tec buffered propionic acid. Use of alternative products may cause complications. Including inaccurate readings from the flow meter and damage to all parts. Resulting in the warranty being void
Made for iPad® running the current iOS operating system
iPad is a trademark of Apple Inc., registered in the U.S. and other countries.
300 Series Applicators with serial number before THS07000 will require the THS to be sent to Harvest Tec for a required update in order to use the iPad Integration Module (030-6670C).
Hay App version must be at least 2.7.1 (or higher) to operate with the iPad Integration Module (030-6672C)
Tools Needed
– Standard socket set
– Standard screw driver or 5/16”
– Side cutter
– Hose cutter
– Crescent wrench
– Hammer
– Metal drilling and cutting tools
– Center Punch

Installation of Applicator

Tank and Saddle Installation

1. Locate the left saddle leg, 001-4703XL, and mount to left side sheet of baler using two 1/2″ x 1-1/2” hex bolts, 1/2″ lock washers, and 1/2″ flat washers. Do not fully tighten.
2. Locate the right saddle leg, 001-4703XR, and mount to right side sheet of baler using two 1/2″ x 1-1/2” hex bolts, 1/2″ lock washers, and 1/2″ flat washers. Do not fully tighten.
3. Roll Belt 460 / 560 and RB465 Installation only! Locate the two anchor extension brackets, 0014703XAX, and attach one extension bracket to the outside of each leg with two 1/2″x 1-1/2” hex bolts, 1/2″ lock washers, and 1/2″ flat washers.
4. Locate the anchor bracket, 001-4703XA, and attach to the side of the extension bracket, 001-4703XAX for 4 X 6 balers (or 001-4703XR and 001-4703XL for other balers) using two 1/2″ x 1-1/2” hex bolts, 1/2″ flat washers, 1/2″ lock washers, and 1/2″ hex nuts. Do not fully tighten. Note that 001-4703XA should be positioned so it is angled toward the round pipe that runs across the width of the baler behind the legs. Repeat procedure for the opposite side.
5. Locate the u-bolts, 001-4703XAB, and attach the 001-4703XA brackets to the round pipe running across the baler. Tighten the u-bolts evenly. **Due to minimal clearance between the anchor bracket and the side sheet, use a deep socket and long extension on a ratchet to tighten u-bolts.
6. With the u-bolts, 001-4703XAB, securely tightened around the round pipe, tighten the bolts connecting the anchor brackets, 001-4703XA, to the saddle legs, 001-4703XL & 001-4703XR.
7. Tighten the hardware attaching the saddle legs, 001-4703XL & 001-4703XR, to side sheets of the baler.
8. Install the tank assembly (tanks, straps, handrail, and saddle pan) on the legs. Secure the saddle pan, 001- 4703X, to the saddle legs with 1/2″ flat washer, 1/2″ lock washer, and 1/2″ hex nut from the bottom side in four locations. Tighten hardware.

4×5 Baler Expanded 4×6 Baler Expanded 5×5 Baler Expanded 5×6 Baler Expanded Installation of Pump Manifold
Mounting Front Pump Plate Support

1. Open right side door of baler.
2. Locate mounting holes for your size baler in bracket (001-4703XE). Mount bracket to pre-stamped square holes on diagonal support structure of baler. Note pictures on following pages will help in locating the prestamped holes on your baler. Secure with two M8 x 25mm carriage bolts and flanged nuts.
3. Disconnect pump mounting bracket (001-4646C) from pump plate by removing four 3/8” x 3/8” flange bolts. Attach right top corner of pump mounting bracket to bracket (001-4703XE) with two 3/8” x 3/4” hex bolts, flat washers, lock washers, and nuts. Note: top of brackets should be flush.

Installation of Control Manifold 2. Use two 3/8” x 3/4” hex bolts, flat washers, lock washers, and nuts to secure Pump Plate Bracket (0014703XF) to back side of Pump Mounting Bracket (001-4646C). Use holes 1 and 2 as designated in Figure 3 on the Pump Plate Bracket (001-4703XF). Slide
the Pump Plate Bracket (001-4703XF) so it touches the door support bracket.
Mounting Rear Pump Plate Support
Mounting bracket 001-4703XF (right) will be used to mount the pump mounting bracket to the door support bracket. However each size baler uses a different set of holes in the rear mounting bracket. Use this guide for proper mount holes with your baler:  Secure with two M8 x 25mm carriage bolts and flanged nuts (Figure 1).

3. Place a level on top of the Mounting Plate (001-4646C) to make sure it is level. Using the Pump Plate Bracket (001-4703XF) as a guide mark holes (D and E) on the door support bracket. Remove brackets (001-4703XF and 001-4646C) for drilling. Center punch holes and drill with a 7/16” drill bit.
4. Once holes are drilled secure (001-4703XF) to door support bracket with two 3/8” x 3/4” hex bolts, flat washers, lock washers, and nuts figure 4.
5. Attach pump mounting bracket back onto brackets (001-4703XF and 001-4703XE) with 3/8” hardware.
6. Attach pump plate with pump onto Mounting Plate (001-4646C) bracket with 3/8” x 3/4” flange figure 5. Installation of Moisture Sensor Pads and Disks

1. Open rear tail gate of baler and lock in the up position. Refer to baler manual to lock door open.
2. Remove bale shaping discs on each side of chamber by grinding welds. Once removed grind any remaining welds so sides of bale chamber are smooth.
3. Place plastic isolator (006-4641FX) in the same spot that the shaping disc had been. There should be a hole in the baler that matches up with the hole in the plastic isolator. If not, use the isolator as a template and mark the hole. Center punch the hole and drill it to 3/4″ (19mm). Note: before drilling make sure you are not drilling into sensitive equipment on the outside of the baler. Drill through the complete square tube, 2” (51mm) in size. Repeat for other side of the baler.
4. Insert plastic bushing (006-4641G) from the outside of baler. Make sure it is flush with the outside of the baler frame. Go to the inside of the baler and mark amount that protrudes into the chamber. Remove and cut off excess material. Repeat for other side.
5. Using 4” (102mm) carriage bolt slide the parts on in following order: metal disc (001-4641HX), plastic isolator (006-4641FX) and shortened plastic bushing (006-4641G).
6. Insert disc assembly into 3/8” (10mm) hole from inside of bale chamber. Secure to outside of baler by attaching to the protruding carriage bolt in the following order: small isolator (006-4641), 1/2” D shaped washer, 1/2” lock washer, 1/2” jam nut. Tighten down and repeat for the other side. Make sure no part of the bolt or hardware makes contact with the frame of baler-no metal to metal.
7. Route moisture harness (006-4640GX) from processor down to the carriage bolt on each side. Make sure it does not come in contact with any moving parts. Secure with cable ties.
8. Attach moisture cable to moisture carriage bolt by placing items in the following order: 1/2” D shaped washer, Ring terminal of moisture harness (006-4640G2), second 1/2” D washer, 1/2” lock washer, 1/2” Jam Nut. Tighten down and repeat for other side. Make sure none of the hardware comes in contact with the frame of the baler.

If there are Rotor Transition Kit (CNH part# 48093991) transition plates installed, they will need to be removed in order to install the moisture discs. Installation of Drain / Fill Kit
Locate parts bag 1. Thread 3/4″ elbow fitting (003-EL3434) into end of tank. Run 3/4″ hose from the elbow down the frame to the bottom of the baler. Locate the two holes on the baler’s angled support bracket that line up with the holes in the valve bracket and attach using two 5/16” x 1” self-tapping screws and secure with two 5/16” flange nuts. Connect valve assembly to other end of hose. Place hose clamps on both ends. Install supplied safety decals (DCL-8001 & DCL-8005) next to the ball valve assembly.
Secure hose to frame using cable locks. Installation of End of Bale Sensor
The bale rate timer sensor is used to determine when the baler door is open. With this information the system is able to change the tons/hour automatically (see Operating Instructions, Automatic Mode).
Locate the sensor (006-7400) and the sensor bracket (001-4648RB). On the right side of the baler find a location 1”– 6” down from the hinge to mount the bracket. Check for clearance with hydraulic cylinders before mounting the bracket. The bracket should be mounted to the front side of the hinge point, with the sensor aligned over the back door.
Mark and drill two 1/4” (7mm) holes and install the bracket using two 5/16” x1/4” self-tapping bolts.
Install the sensor into the bracket and leave 1/4″ (7mm) of clearance between the end of the sensor and the door.
The harness will need to be routed towards the DCP. Secure with cable ties and take care to avoid pinch points. The harness extension (006-7400EXT) may need to be used. Installation of the Spray Nozzles
a. Locate nozzle block hanger assemblies with tips pre-installed.
b. The assembly with the tee fittings will be mounted to the right hitch support plate when standing next to the PTO just in front and under the large round cross support tube. Use 1/2” x 1 1/4” Bolt, flat washer, lock washer, and nut to secure to baler. Repeat for assembly on the other side.
c. Loosen Philip screw on nozzle block and turn them slightly in toward each other.
d. Measure distance between hose barb fitting and cut the hose to that length. Attach to the nozzle assembly and secure them with hose clamp. For roto-cutter models with hydraulic lines- hosing may need to be routed either above or below the hydraulic lines to allow for proper nozzle placement. Hydraulic lines, secured by factory plastic zip ties, may need to be adjusted to accommodate hose routing for proper nozzle angle placement.

Refer to Tip Output under APPLICATION RATE of the control unit to calibrate system.
Installation of Plumbing
A. Intake
Locate parts bag 16. Use the 003-EL3412 on the bottom of the tank to route 1/2″ line (002-9001) to the 003-A1212 or 003-EL1212 fitting used on the ball valve attached to the pump plate. Attach hose clamps (003-9003) on both of the fittings.
B. Discharge
Route the 1/2″ hose from the pump output toward the front of the baler and connect to the solenoid assembly (SOL-3SP-B). Secure the solenoid assembly and hose along baler, positioning the solenoid as close to the spray tips as possible. Connect the 1/4″ hose to the outgoing side of the solenoid to tip assembly.
C. Standard and Low Output Tips
Your baler comes with two sets of tips: a low set and a high set.
-The low set will cover outputs of 60 – 300 lbs/hr (27-300 L/hr).
-The standard set will cover outputs of 48- 448 lbs/hr (21-203 L/hr).
Installation of iPad Integration Control
Locate a safe location in the cab of the tractor to place the iPad Integration Control (030-6672C). Recommended location is securely fastened out of the operators way in a location that is close enough to reach with the iPad cord. Connect the Power / Communication harness (006-6650TM(E)) to the bottom of the receiver.
To operate the applicator, plug the iPad cord into the communication port indicated by: iPad Integration Control Light Signals
Green Slow Blink – Power supplied to the applicator system and the unit is going through its startup process. This will take approximately 25-35 seconds.
Green Double Blink – Indicating the iPad module recognizes the iPad but the app is not open or connected.
Green Solid Light – Module is connected to the app and is ready to operate.
Recommended to use the USB cable included with the applicator kit (006-6672USBC)
Bluetooth Receiver Lights
Pre-2020 applcaitors equipped with Bluetooth receivers (030-6672B) are now equipped with lights to indicate both power and Hay App connection on the Apple iPad. Clean light regularly
Blinking Lights – System is waiting for the processor to connect, which could take up to 35 seconds.Red Light – The Bluetooth receiver has power
Green Light – The Bluetooth receiver is connected to the Hay App.
300 Series Applicators with serial number before THS0700 will require the THS to be sent to Harvest Tec for a required update in order to use the iPad Integration Module (030-6670C)
Hay App version must be at least 2.7.1 (or higher) to operate with the iPad Integration Module (030-6672C)
Made for Apple iPad badge**
Use of the Made for Apple iPad badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
Please note that the use of this accessory with an Apple product may affect wireless performance.

**Wiring Diagram

**

347C

1. Connect the power harness (006-3650T) to the tractor battery (12 volt) using the red wire with fuse to the positive side and the black wire to the negative.
   a. The power harness must be connected to the battery! The unit will draw more amps than convenience outlets can handle. Any modifications of the power harness will void systems warranty. CONTACT HARVEST TEC BEFORE MODIFICATIONS.
   b. This unit will not function on positive ground tractors.
   c. If the unit loses power while operating it will not keep track of accumulated pounds of product used.

2. The power harness on the tractor (006-3650T) will run from the tractor battery to the hitch. The power harness on the baler (006-3650B1) will connect to the tractor power harness (006-3650T) at the hitch.

3.  Connect the keyed power wire (006-5650K) to a keyed power source on the tractor. The keyed power wire must connect to a keyed source or the unit will not power up correctly.4. Attached the iPad Integration Control (030-6672C) to the tractor power harness (006-3650T).

4. Attach the End of Bale (EOB) connection on the controller to the End of Baler Sensor (006-7400).

5. Attach the Solenoid (V1) (Delphi connector) connection on the controller to the wire from the solenoid (002-2203F). Note: If solenoid is connected to V2-DSM (not used) connection, solenoid will not work.

6. Attach the Flowmeter (FLOW) connection on the controller to the flowmeter (006-4729A).
   a. Attach the spade connectors on the FLOW harness to the Pump (007-4120DE).

System wiring diagram

**Pin Outs

**

Power Harness 006-3650T at Tractor Hitch

Power Harness 006-3650B1 at Baler Hitch

Pin 3
Pin 4
Pin 5| Orange Not Used
Green| Keyed Power
HT Can Low
Pin 6
Pin 7
Pin 8| Yellow Not Used
Black| HT Can Hi
Ground from BLE
Pin 9
Pin 10| Black
Not Used| Ground from THS

iPad Integration Control / BLE on Harness 006-3650T

Pin 3
Pin 4
Pin 5
Pin 6
Pin 7| Yellow
Not Used
Green
Not Used
Not Used| HT Can Low HT Can Hi

End of Bale Sensor at 300 Controller Harness

Flow Meter at 300 Controller Harness

End of Row Sensor at 300 Controller Harness

Moisture Sensor connection at 300 Controller Harness

Pin 1| Not Used|
---|---|---
Pin 2| Not Used
Pin 3| Not Used
Pin 4| Not Used
Pin 5| Not Used
Pin 6| Not Used
Pin 7| Not Used
Pin 8| Blue| Signal for Sensor 1
Pin 9| Blue| Signal for Sensor 2

Pump connection at 300 Controller Harness

Solenoid Connection at 300 Controller Harness

V2-DSM Connection at 300 Controller Harness

Parts Breakdowns

Model 347C Base Kit![HARVEST TEC 347C 55 Gallon Preservative Applicators

• parts28](https://manuals.plus/wp-content/uploads/2024/03/HARVEST-TEC-347C-55 -Gallon-Preservative-Applicators-parts28.jpg)

Ref| Description| Part #| Qty| Ref| Description| Part #| Qty
---|---|---|---|---|---|---|---
1| 55 Gallon tank lid| 005-9022H| 1| 7| Anchor Bracket| 001-4703XA| 2
2| Strap| 001-4402| 2| 8| Saddle| 001-4703X| 1
3| Tank| 005-9203SQ| 1| 9| Left Leg| 001-4703XL| 1
4| Handle| 001-6707HRS| 1| 10| Right Leg| 001-4703XR| 1
5| Anchor Bracket Ext| 001-4703XAX| 2| 11| Tank fitting| 005-9100| 2
6| U Clamp| 001-4703XAB| 2| | |
| | | | | Tank Kit Assembly| 030-0447C-TK (1-11)

Parts Bag Packages

Parts Breakdown for Pump Assembly

Part#| Description| Qty| Part#| Description| Qty
---|---|---|---|---|---
003-EL3812| 3/8”MPT X 1/2″HB Elbow| 1| 003-M1212| 1/2″ Union| 2
007-4120DE| 300 Series Pump| 1| 002-4315-100| 1/2″ Line Strainer-100 Mesh| 1
003-M3838| 3/8” x 3/8” Union| 1| 003-SE12| 1/2″ Street Elbow| 1
003-SE38| 3/8” Street Elbow| 1| 002-2212| 1/2″ Ball Valve| 1
002-4566F| 3/8” Check Valve| 1| 003-EL1212| 1/2″MPT x 1/2″HB| 1
003-RB3814PB| RB 3/8” x 1/4” Reducer| 1| 001-4648XL| 300 Pump Support| 1
006-4729A| Flow Meter – Block Style| 1| 001-4648X| Pump Plate Mount| 1
003-RB1214PB| RB 1/2″ x 1/4″ Reducer| 1| 003-A1212| Not Pictured|
003-M1212F| 1/2″ Coupler| 1| 003-A3812| Not Pictured|
| | | Pump Assembly PMP-3636P (001-4648X Not Included)

Completed Assembly *Note: Due to alternative baler designs, elbow 003-EL3812 can be replaced by straight fitting 003-A3812. As well as elbow 003-EL1212 can be replaced by straight fitting 003-A1212. Both straight fittings are included.
Moisture Sensor Discs

Ref| Description| Part #| Qty| Ref| Description| Part #| Qty
---|---|---|---|---|---|---|---
1| RB Isolator| 006-4641FX| 2| 6| 1/2″ x 4 1/2” Carriage Bolt| Hardware| 2
2| RB Moisture Pad| 006-4641HX| 2| 7| Sensor Bushing| 006-4641G| 2
3| 1/2” Nut| Hardware| 4| 8| Plastic Isolator| 006-4641I| 2
4| 1/2″ Lock| Hardware| 4| 9| Moisture Cable| 006-4640GX2| 1
5| 1/2″ D Washer| Hardware| 6| | | |
| | | | Moisture Assembly (Ref 1-8)| 030-4643C| 2
| | | | Complete Assembly (Ref 1-9)| MSH-RB-B|

Hoses

Control Box and Wiring Harnesses

End of Bale Sensor Kit A

347C-SO Installation Kit

Ref| Description| Part #| Qty| Ref| Description| Part#| Qty
---|---|---|---|---|---|---|---
1| Spray Block Holder| 001-4703XD| 2| 6| Plug Allen SS| 003-F14A| 2
2| 1/4″ x 1/4″ Straight Fitting| 003-A1414| 5| 7| Tip – Pink| 004-T8004-PT| 2
3| 1/4″ Sq Tee| 003-TT14SQ| 1| 8| Tip – Grey| 004-T8008-PT| 2
4| Mini Hose Clamp| 003-9002| 6| 9| Spray Shield Manifold| 001-4435NSB| 1
5| 1/4″ Female Street Elbow| 003-SE14F| 1| | | |

• Tip color subject to change| | | | Complete Assembly| 030-0347C-SO|

300 Solenoid Packages Solenoid Package B

Ref| Description| Part #| Qty| Ref| Description| Part #| Qty
---|---|---|---|---|---|---|---
1| Solenoid Harness (10’)| 006-3650-S2| 1| 6| 1/4″ Female Disconnect| 004-1207H| 2
2| #6 Hose Clamp| 003-9003| 1| 7| Solenoid| 002-2203F| 1
3| 1/4″ x 1/2″ Straight Fittng| 003-A1412| 1| 8| Solenoid Valve Body| 004-1207VF| 1
4| 1/4″ Female Connector| 004-1207G| 1| 9| 1/4″ x 1/4″ Straight Fitting| 003-A1414| 1
5| Rubber Washer| 004-1207W| 2| 10| Mini Hose Clamp| 003-9002| 1
| | | | | Complete Assembly| SOL-3SP-B|

Optional High Output Kit (300RBHTK)

High Output Solenoid
(Included with 300RBHTK Kit)

Optional iPad Mini Mounting Kit (030-2014MK)

Installation Instructions

1. Identify 12V power source for wires to connect.
   a. Eye loops included if wiring directly to the battery is desired.
   b. Test for key power source if preferred to have power to the USB shut off with the key.

2. Once power source is identified, cut wires to desired length.

3. Crimp the two supplied quick connectors onto each the white and black wire.

4. Remove the round locking plastic nut from USB plug before connecting the wires. Black (+) White (-).

5. The wires will then be hooked to the designated terminals on the bottom of the USB plug

6. Drill a 1 1/8” hole in the preferred mounting location. Be sure to clean any sharp edges after drilling.

7. Feed the wires through the mounting hole.

8. If using the round plastic nut to secure plug in place, slide the nut back over the wiring before connecting the wires to powered source.

9. Connect the wires to the identified power source if easier to do so before tightening the plug into place.

10. Tighten plug using either the round plastic nut or mounting plate and two screws, both options supplied.

11. Once connected, hook a USB charging cord into the plug and connect a mobile device/tablet to ensure the plug is operating as you wish (key power working properly if necessary).

NOTE: This plug is not designed to charge two iPads. System damage could occur if this is attempted.
System will charge a mobile phone and iPad simultaneously without problem.
*iPad mini is a trademark of Apple Inc., registered in the U.S. and other countries.
Optional iPad Display Kit (030-4670DK)

Ref| Description| Part #| Qty| Ref| Description| Part #| Qty
---|---|---|---|---|---|---|---
1| Suction cup mount| 001-2012SCM| 1| 7| iPad Mini Charger 12V| 001-2012P| 1
2| Ram mount| 001-2012H| 1| 8| iPad Mini 4 case| 001-2012C4| 1
3| iPad Mini spring load cradle (Mini 4)| 001-2012SLC| 1| 9| iPad Mini 4| 006-4670IP| 1
4| 16 gauge power wire| 006-4723P| 1| NP| 4 amp fuse| Hardware| 1
5| Female spade connector| Hardware| 2| | |
6| Eye loop connector| Hardware| 2| | Mounting Kit Assembly| 030-4670DK
| | | | | | (Includes All Parts)

Installation Instructions

1. Identify 12V power source for wires to connect.
2. Eye loops included if wiring directly to the battery is desired.
3. Test for key power source if preferred to have power to the USB shut off with the key.
4. Once power source is identified, cut wires to desired length.
5. Crimp the two supplied quick connectors onto the white and black wire.
6. Remove the round locking plastic nut from USB plug before connecting the wires. Black (+) White (-).
7. The wires will then be hooked to the designated terminals on the bottom of the USB plug
8. Drill a 1 1/8” hole in the preferred mounting location. Be sure to clean any sharp edges after drilling.
9. Feed the wires through the mounting hole.
10. If using the round plastic nut to secure plug in place, slide the nut back over the wiring before connecting the wires to powered source.
11. Connect the wires to the identified power source if easier to do so before tightening the plug into place.
12. Tighten plug using either the round plastic nut or mounting plate and two screws, both options supplied.
13. Once connected, hook a USB charging cord into the plug and connect a mobile device/tablet to ensure the plug is operating as you wish (key power working properly if necessary).

NOTE: This plug is not designed to charge two iPads. System damage could occur if this is attempted.
System will charge a mobile phone and iPad simultaneously without problem
*iPad mini is a trademark of Apple Inc., registered in the U.S. and other countries.

Harvest Tec LLC. Warranty and Liability Agreement

Harvest Tec, LLC. will repair or replace components that are found to be defective within 12 months from the date of manufacture. Under no circumstances does this warranty cover any components which in the opinion of Harvest Tec, LLC. have been subjected to negligent use, misuse, alteration, accident, or if repairs have been made with parts other than those manufactured and obtainable from Harvest Tec, LLC.
Our obligation under this warranty is limited to repairing or replacing free of charge to the original purchaser any part that in our judgment shows evidence of defective or improper workmanship, provided the part is returned to Harvest Tec, LLC. within 30 days of the failure. If it is determined that a non-Harvest Tec branded hay preservative has been used inside the Harvest Tec applicator system where the failure occurred, then Harvest Tec reserves the right to deny the warranty request at their discretion. Parts must be returned through the selling dealer and distributor, transportation charges prepaid.
This warranty shall not be interpreted to render Harvest Tec, LLC. liable for injury or damages of any kind, direct, consequential, or contingent, to persons or property. Furthermore, this warranty does not extend to loss of crop, losses caused by delays or any expense prospective profits or for any other reason. Harvest Tec, LLC. shall not be liable for any recovery greater in amount than the cost or repair of defects in workmanship.
There are no warranties, either expressed or implied, of merchantability or fitness for particular purpose intended or fitness for any other reason.
This warranty cannot guarantee that existing conditions beyond the control of Harvest Tec, LLC. will not affect our ability to obtain materials or manufacture necessary replacement parts.
Harvest Tec, LLC. reserves the right to make design changes, improve design, or change specifications, at any time without any contingent obligation to purchasers of machines and parts previously sold. Revised 4/17

HARVEST TEC, LLC.
P.O. BOX 63
2821 HARVEY STREET
HUDSON, WI 54016 USA
PHONE: 715-386-9100
1-800-635-7468
FAX: 715-381-1792
Email: info@harvesttec.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>