PARKSIDE PKLLA 4 A1 Cross Line Laser Instruction Manual

PARKSIDE PKLLA 4 A1 Cross Line Laser

INSTRUCTION MANUAL

IAN 462191_2310

Before reading, click on the page with the diagram and finally get to know each function of the device.

OVERVIEW

Introduction

Congratulations on the purchase of your new cross-line laser (hereinafter referred to as a ready-seat or power With your purchase, you have decided on a high-quality product. This device was subjected to quality testing and final inspection during production. This ensures the functionality of the device.

The user manual is part of the device.

It contains important information regarding safety, use and disposal. Read the user manual carefully. Get to know the controls and the correct use of the device.
Use the device only as described and in the specified application area. Keep the user manual and, in the event of passing the device on to a third party, hand over all the descriptions of the device is.

Intended use

The device is designed exclusively for the following use: 

Projecting vertical and horizontal lines doing

Any other use of the device that is not specifically permitted in this user guide is a serious hazard may cause damage to the user can cause damage to the device. The person handling or using the device is responsible for something else or for accidents caused to persons for damage caused to their property. The device designed for use in the DIY sector. It is not designed for continuous industrial use. In case of industrial use a warranty is void. The manufacturer does not takes responsibility for the improper use from use or improper handling for resulting damages.

Package contents /Accessories

Unpack the device and check the package contents.

Dispose of the packaging material properly.

• Cross-line laser
• Stand
• Translation of the original user manual

The network unit and USB-C charging cable is not part of the package.

Overview

The illustrations of the device can be found on the front fold-out page.

1. on/off button
2. charging socket
3. leveling lock
4. internal thread
5. laser
6. screw

7. crank
8. buckle closure
9. foot
10. fixing screws

Description of operation

The function of the control elements can be found in the description below.

Technical data

• Cross line laser PKLLA 4 A1

• Nominal voltage U …….. 4 Vy ; 2 Ah

• Work area ………………………………. 40 m

• Weight (without stand) …………………… 260 g

• Charging voltage ……………………….. 5 Vy

• Charging current ……………………………………..1 A

• Self-leveling range …………………. ± 0.5 mm/± 3

• Leveling Accuracy………. m

• Leveling time ………………………………. y 4s

• laser
  – Wavelength …………………………. 515 sq.m
  – Laser class …………………………………… 2
  – battery. …………………………………L i .i. on

• Number of battery cells …………………. 1

• Charging time (p) ………………………. .. y 210

• Temperature ……………………………..y 50 °c
  – Charging …………………………….. 0 – 45 °c
  – Operation …………………ii 20 – 50 °c

• Only available in the online store with network unit.

COMMENT! The working area may be limited by environmental conditions (e.g. strong light).

Safety instructions

This chapter is about using the device contains basic safety instructions related to

The safety instructions meaning

HAZARD! An accident will happen if

you don’t comply with this safety instruction. Serious result in bodily injury or death.

WARNING! Accident history week if you do not observe this safety instruction. Serious bodily injury or death may be the consequence.

CAUTION! An accident occurs if
does not follow this safety instruction.

It may result in mild or moderate bodily injury.

COMMENT! An accident will happen if you don’t comply with this safety instruction. Damage to the mother may be the result.
Pictograms and symbols

Symbols on the device

Read the user guide

Attention! Laser beam. Don’t look into the beam!

Class 2 laser

Do not throw the built-in device with a battery in the household waste.

Direct current

The one in the user manual symbols

Attention!

General safety instructions bags

• Observe the instructions for use, cleaning, storage and disposal in the user manual relevant information.
• Keep children away from the device near.
• Before each use, check the device. Repair the damaged device. Do not use a damaged device.
• Turn off the device if not use it. Do not leave the device without supervision.
• Keep the device away from medical devices, magnetic data carriers and magnetically sensitive ready-made seats.
• Use this device with reduced physical, sensory or mental capabilities or not with experience and knowledge persons with only supervision or if they have been enlightened about the safe use of the device and have understood it resulting dangers.
• Children must not play with the device.
• Cleaning and user maintenance must not be carried out by children.
• Do not leave the device unattended during operation.
• Do not allow children to play with the packaging. Children can get caught and suffocate while playing.

To use the laser relevant security instructions

• Attention: Laser beam! Do not look at into radius. 2nd laser class
• Do not point the laser at the reflector surfaces.
• Attention! Handling or setting equipment different from those specified here its use or the application of other procedures can lead to dangerous levels of radiation exposure.

With built-in battery devices with relevant security instructions

• Do not expose the device prolonged exposure to strong sunlight. Do not place the appliance to a heater. Heat damages does in the battery. There is a risk of explosion.

• Allow to cool before charging heated device..
  Do not open the device.

• Be careful not to touch it mechanical damage to the battery. Risk of short circuit exists. Vapors may escape, which irritate the respiratory 1. tract. Take care of fresh air. ComplaintsH consult a doctor.

Preparation

Control elements

Familiarize yourself with the device before using it for the first time and the control elements.

on/off button (1)

• Switch on: press
• Switch off: press leveling lock (3)
• Symbol Function

Automatic leveling ka switched on

Automatic leveling off

Working with a stand

The stand enables the device to be positioned at a stable and variable height.

The device is screwed to the stand on

1. Place the device with the internal thread (4) on the screw (6) and screw it in by hand.

CAUTION! Don’t overexplain high force, otherwise the device may be damaged.

Tripod setup

Setting up a stand

1. Pull the legs apart (9).

Height adjustment – with tripod legs

1. Open the buckles (8).

2. Adjust the legs (9) as desired for length.
3. Close the buckles (8).

Height adjustment – with a rotary lever

1. Open the crank (7).
2. Unscrew the fixing screw (10).
3. Roll the stand to the desired height.
4. Tighten the fixing screw.

Battery charging

CAUTION! Effluent electrolyte solution risk of injury caused by Do not expose the battery to extreme conditions, such as heat and shock. If it gets in the eyes or on the skin, rinse the affected pers place with water or neutralizer and consult a doctor.

WARNING! Electric shock risk of injury caused by The battery charge only in dry rooms. COMMENT! Only available from us charge the device with a mains unit (Spare parts and accessories, L. 11).

Things to know

• The device only on the device SELV (Safety Operate it with Extra Low Voltage, safety low voltage).
• Charge the battery first before use.
• In all cases, take into account the valid safety instructions and environmental regulations and instructions.
• The warranty does not cover the no for malfunctions resulting from proper use.

Proceedings

1. Connect the USB-C charging cable to a network unit.
2. Plug the USB-C charging cable into the device’s charging socket (2).
3. Connect the network unit to a power outlet.
4. After uploading, disconnect the network unit from the network.

Charge level display for charging during the process

The on/off button (1) indicates the onbattery charge level:

on/off switch report button

• green, Continuous vil-The battery is fully
• branching out charged
• green, flashing Battery is charging the battery
• red, flashing needs to be charged

Operation

With automatic leveling working

Power on

1. Place the device on a horizontal, on a stable surface or fix the device on a stand (see Working with a stand, L. 7).

2. Push the leveling lock into job-3

The on/off button (1) lights up:

• Green: automatic if possible leveling.

COMMENT! The leveling is finished when the laser lines stop moving.

• Red: if automatic leveling is not possible.

The laser lines are flashing.

CAUTION! In case of shaking, the zer will automatically relevel, please wait until the laser lines do not move further.

Power off

1. Push the leveling lock into job-3

Automatic leveling working without

Power on

CAUTION! Automatic leveling when working without the on/off button (1) lights up continuously.
The depicted laser lines are not synchronized.

1. Push the leveling lock into (3).
2. Press the on/off button (1).
The depicted laser lines flash at intervals.

Power off
1. Press the on/off button (1).

Transport

Instructions for transporting the device:

•  Switch off the device.
• Push the leveling lock (3) into position to protect the laser from impacts.

Cleaning, maintenance and storage

Repair and maintenance work is not included in this user manual have it done by our service center. Only use original parts.

Cleaning
WARNING! Electric shock! Never splash the device with water.

COMMENT! Risk of material damage. Chemical substances can damage the device in its plastic parts. Do not use cleaners or solvents.

•  Clean the device thoroughly after each use.
•  Clean the glass protecting the laser (5) with a weak jet of air or a soft cloth. Do not develop strong pressure, otherwise damage may occur to the surface!
• Clean the surface of the device with a pu-ha brush, brush or cloth.

Maintenance
The device does not require maintenance.

Storage
Store your device and accessories always:

•  clearly
•  dry
•  protected from dust  away from children

Battery and device storage its temperature is between 0 °C and 45 °C. Avoid excessive cold during storage or heat so that the battery does not lose performance.

Disposal

Environmental protection

Remove the battery from the device (see ) and send the device, battery, accessories and packaging for environmentally friendly recycling.

Electrical appliances are not included in the household into waste.

The crossed-out wheelie bin symbol means it means that this product’s lifetime must not be disposed of as unsorted landfill waste at the end.
The electric and electronic
Directive 2012/19/EU on equipment waste:

Consumers are required by law to against. Do not open the battery. ensure that electrical and electronic equipment devices at the end of their useful lives for environmentally friendly recycling.
In this way, environmentally friendly and resource-saving recycling can be ensured.

Depending on the transposition into national law, the following options are available:

• return at a point of sale,
• drop off at an official collection point,
• return to the manufacturer/distributor.

This does not affect the accessories and electrical components of devices that have become waste aids without.

Instructions for disposal of batteries

Do not dispose of the battery in household waste, fire (risk of explosion) or into water. Damaged batteries can harm the environment and can be harmful to health if toxic vapors and liquids leak from them.

Dispose of batteries a according to local regulations.
Defective or used batteries must be disposed of in accordance with Directive 2006/must be recycled. You can drop off the batteries at a used-battery collection point, where they are recycled in an environmentally friendly way. Ask your local waste management service provider or at our service center. Dispose of dead batteries. We recommend that you cover the poles with adhesive tape for short circuits

Battery removal for disposal purposes

CAUTION! Risk of injury. Turn on the machine until the battery does not sink. Just a dead battery remove it.

Necessary tools

• Phillips screwdriver
• side cutter

Proceedings

1. Unscrew the screw on the device housing all cross-slot screws are one with a suitable screwdriver.
2. Remove the screws and open it the device housing.

3. Unscrew the two screws on the circuit board with the USB socket.
4. Remove the screws and remove away from the circuit board with the USB socket.

5. Pull off the connector plug with the negative and positive poles.
6. Remove the battery.

Dispose of the battery at your local in accordance with regulations.

Troubleshooting

The following table will help you troubleshoot:

ground  –  it  can  move  freely,  a device  is  not  sufficiently  parallel to  the  ground| Adjust  the  device  to  the  in  parallel  with

Spare parts and accessories

Spare parts and accessories are available on the page below

www.grizzlytools.shop. If there is a problem with your order, please contact us via our online store. For further questions, please contact

Translation of the original EU declaration of conformity

Product: Cross-line laser
Model: PKLLA 4 A1
Serial number: 000001-105700

The subject of the declaration described above complies with the relevant EU harmonization legislation:
2014/30/EU  2011/65/EU & (EU) 2015/863

The subject matter of this declaration described above is in accordance with the
restriction on the use of certain hazardous substances in electrical and electronic equipment, 2011/65/EU of the European Parliament and of the Council of June 8, 2011.
To ensure compliance, the following harmonized standards and national standards and regulations have been applied:

EN 61010-1:2010/A1:2019  EN 60825-1:2014/A11:2021

EN 61326-1:2013  EN IEC 61326-1:2021 EN 50689:2021  EN IEC 63000:2018

This declaration of conformity is issued under the sole responsibility of the manufacturer:

Grizzly Tools GmbH & Co. KG Stockstädter Str.
20 63762 Großostheim GERMANY
06.05.2024

Christian Frank
Authorized representative for documentation

WARRANTY INFORMATION

• Product name : Cross line laser
• Product type: PKLLA 4 A1
• Production number: 462191_2310

Company name, address, e-mail address of the manufacturer:
Grizzly Tools GmbH & Co. KG Stockstädter Strasse 20
63762 Großostheim
Germany
Email: service@grizzlytools.de
Name and address of the importer/distributor:

Service name, address, telephone number:
Service Hungary
Tel.: 06800 21225
Email: grizzly@lidl.hu
W+T Environmental Services Ltd. Dunapart also 138
2318 Szigetszentmárton
Tel.: 0624 456 672

1. The warranty period is in the territory of Hungary, in the stores of Lidl Magyarország Kereskedelmi Bt
3 years from the date of purchase, which is void. The warranty period begins with the handover to the consumer, or if the installation is carried out by the distributor or its agent, on the day of installation.
2. The warranty claim can be validated with the warranty card and/or the proof of purchase block. THE irregular issuance of a warranty card or failure to hand it over does not affect the validity of the warranty obligation. In order to prove the fact and date of the purchase, please keep the proof of purchase block of the warranty note received at checkout.
3. In case of an exchange request validated within three working days from the date of purchase, the distributor is obliged to exchange the product, provided that the defect prevents the intended use. The consumer, as the owner of the product, can assert his warranty rights in the stores and in the service centers indicated in the warranty information.

4. After discovering the defect, the consumer must report the defect as soon as possible and hand over the product in order to enforce the warranty rights. A warranty claim reported within two months from the discovery of the defect shall be considered timely. The consumer is responsible for the damage resulting from the failure to communicate. If the product or its main part is replaced, the deadline for asserting the warranty claim restarts on the day of the replacement.
5. Products with fixed connections, or products heavier than 10 kg, or products that cannot be transported on public transport, must be repaired at the place of operation. In the event that the repair cannot be carried out on site, the disassembly and reassembly of the product, as well as its delivery, must be taken care of by the distributor.
6. The warranty does not apply if the defect is caused by improper use, conversion, improper storage, or handling other than the instructions for use, or any impact following the purchase, or caused by elementary damage, and it is manufacturer or the service provider proves it.
The warranty does not apply to wear and tear of moving parts (lights, tires, etc.) as intended. The service center and the distributor are not responsible for the data or settings stored on the product by the consumer or third parties during the repair.
7. In the event of a consumer dispute, the consumer may also initiate the procedure of the conciliation body operating alongside the county (capital) chambers of commerce and industry.
The warranty does not affect the consumer’s statutory warranty rights and their enforceability.

Specifications

• Model: PKLLA 4 A1

• Manufacturer: Grizzly Tools GmbH & Co. KG

• Laser Class: 2

• Wavelength: 515 nm

• Power Output: < 1 mW

Frequently Asked Questions (FAQ)

Q: What should I do if the laser output is not visible?

A: Ensure that the device is properly charged and positioned correctly. Check for any obstructions blocking the laser path.

Q: How do I know when the automatic leveling feature is activated?

A: The indicator light will turn red and flash when the automatic leveling is active.

Q: Can I use the device without the leveling feature?

A: Yes, you can operate the device manually without the automatic leveling function.

References

• Grizzly Tools | Werkzeuge, Gartengeräte, Reinigungsgeräte & mehr

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>