Panasonic F-PXU70M Air Purifier Instruction Manual

Panasonic F-PXU70M Air Purifier Instruction Manual

SAFETY PRECAUTIONS

Please strictly follow

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

• Disconnect power supply before maintenance.

• This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the product by a person responsible for the safety.
  Children should be supervised to ensure that they do not play with the product.
  The safety precautions should be strictly followed in order to prevent injury or damage to properties.

• The following symbols differentiate the levels of danger or injury that may result if the product is not used correctly as instructed.

WARNING
Those things shown in this column indicate that there is possibility of causing death or severe injury.

**** Those things shown in this column indicate that there is possibility of causing minor injury or damage to properties.

• The following symbols are used to indicate the type of instructions that need to be followed. (The symbols given below are examples)

This symbol indicates an action that must not be performed.

This symbol indicates an action that must be performed.

WARNING

• Do not pull the power cord when carrying or storing the product.
  (Otherwise, the power cord may be damaged with the possibility of fire or electric shock.)

• Do not damage the power cord or power plug.
  Do not cut, modify, excessive distort, twist, squeeze the power cord, and do not place it near heat sources, place heavy weight on it, etc.
  (Otherwise, the power cord may be damaged with the possibility of fire or electric shock.)

• Do not touch the power plug with wet hands.
  (Otherwise, electric shock may occur.)

• Do not disassemble or modify the product.
  (Otherwise, the product may catch fire or malfunction, thus resulting in fire or electric shock.)Contact the dealer for repair.

• In case of any abnormality or malfunction, stop using the product immediately and disconnect the power plug
  (Otherwise, electric shock, fire or smoke may occur.) <Examples of abnormality/malfunction>

• The product stops operating when moving the power cord.

• If any switches do not work.

• If the circuit breaker is tripped or when fuse blows.

• If the power cord or power plug becomes abnormally hot.

• If you notice a burning smell or an abnormal sound or vibration.

• If there is any other abnormalities or malfunction

• Please stop using the product immediately and disconnect the power plug, and contact the dealer to check and repair.

WARNING

• Do not use power other than the rated voltage.
  (Otherwise, the power cord may overheat and induce fire.)

• Do not insert your fingers, metallic objects or others into the air inlet, air outlet or gaps.
  (Otherwise, you may be hurt by the inner units with the possibility of electric shock or injury.)

• Do not let the product get wet
  Do not place cups, etc. on the product.
  (Otherwise, the product may short circuit with the possibility of fire or electric shock.)

•  Clean the power plug regularly.
  (If dust is found on the power plug, insulation maybe damaged by humidity and fire may occur.)

• Disconnect the power plug and wipe it with dry cloth.

• When the product will not be used for a long period, disconnect the power plug.

• Insert the power plug completely.
  (If the power plug is not fully inserted, the power cord may be overheated, thus resulting in fire or electric shock.)
  Do not use damaged power plug or loosen power socket.

CAUTION

•  Do not place the product in the following places.

  • Incline and unstable place.
    (Otherwise, the product may fall over and injury may occur or damage the product.)

  • Where the temperature or humidity is extremely high, or watery area, such as bathroom.
    (Otherwise, current may leak with the possibility of fire or electric shock.)

  • Where oil fume is emitted, such as in kitchens.
    (Otherwise, the product may crack and injury may occur.)

  • Where oil or inflammable gas is present and may be leaked.
    (Otherwise, a fire may occur due to ignition in the product.)

  • Where the air outlet faces animals or plants directly.
    (Otherwise, it may cause discomfort to animals and dry out plant.)

•  Do not operate this product in places where indoor fumigation type insecticides are being used.

  • (Chemical residue may build up inside the product and discharge from the air outlet, and cause damage to health.)
  • Ventilate the room with fresh air thoroughly after using insecticides before operating the product

• Do not place the product near combustible materials such as lighted cigarette, incense, etc.
  (Otherwise, these may be absorbed into the product with possibility of fire.)

• Do not sit on or lean against this product.
  (Otherwise, the product may fall over and injury may occur or damage the product.)
  Families with children should pay more attention.

•  Do not clean the product with gasoline or other volatile mixture solvents, and avoid contacting with spray insecticides.
  (Otherwise, the product may crack or short circuit with the possibility of injury, fire or electric shock.)

• Do not place books, clothing or any other objects at the air outlet of the product.
  (Otherwise, the air outlet may be blocked, thus resulting in smoke and fire.)

• When disconnecting the power plug, hold the power plug instead of the power cord
  (Otherwise, the power cord may be damaged with the possibility of fire or electric shock.)

• When carrying the product.
  Please hold the back handle of product, but not the inlet cover.
  (Otherwise, it may break or fall off, thus resulting in injury.)
  

• Keep the room well-ventilated when using the product together with a burner.
  (Otherwise, carbon monoxide poisoning may occur.)
  This product cannot remove carbon monoxide.

SETTING AND OPERATING REQUIREMENTS

Area that can enhance the effectiveness!

• Way to against PM2.5 and indoor dust, etc.
  Since PM2.5 or dust is likely to float in the air near the floor, we recommend you to put the product on the flat floor in the room.

• Way to circulate air more effectively.
  Place the product with its left, right and top about 30 cm or more away from walls, furniture or curtains, etc. Otherwise, the pollutants are difficult to be cleared. To ensure effectiveness of this product, keep its back at least 30 cm away from the wall.

• If the product is used in the same place for a long period.
  It may result in dirty surrounding walls or floor. We recommend that you move the product away from where it is placed when maintenance it.

• Do not place any object on the product.
  (Otherwise, the product may malfunction.)

• Do not set the product in the following places

  • Where the product will be exposed directly to sunlight, outlet of air conditioner or heat, etc.
    (Otherwise, deformation, degeneration, discolor or malfunction may be occurred.)

  • Near equipment such as TV and radio.
    (Otherwise, visual disturbances or noises may be caused.)

  • Keep the product 1 m or above away from such devices.

• Do not place obstacles on the product air inlet and outlet.
  (Otherwise it may affect product performance.)

• Do not use the same power socket with TV, radio, etc.
  (Otherwise, visual disturbances or noises may be caused.)

  • In this case, insert the power plug into another power socket.

• Install the product in a place without any obstacles on the left, right, top and back of the product.
  (Otherwise, it is difficult for the product to inhale pollutants, or the airflow may be blocked and cannot be discharged smoothly.)

• Do not place the product on an unstable or uneven surface.
  (Otherwise, vibration may be caused.)

PRODUCT FEATURES

The efficient “HEPA composite filter” brings you fresh and clean air

• The gas pollution level display keeps you updated with the indoor gas pollution level.
• The PM2.5 concentration reading display keeps you updated with the indoor PM2.5 pollution level.
• With the nanoeTM X technology

About nanoeTM X

• The so-called nanoeTM X are charged water purification particles generated by applying high voltage to separate water molecules.
• nanoeTM X features: high moisture content, small particles, high stability, etc.
  

1. High moisture content (the moisture content is 1,000 times the moisture content of ordinary anions).
2. Small particles (about 5 nm – 20 nm (nanometers) in size, able to penetrate deep into the fiber and stratum corneum).
3. High stability (6 times more stable than a common ion, covering a distance of 10 m or above).
4. More hydroxyl radicals (up to 4,800 billion of radicals are generated per second).
5. Weak acidity (with weak acidity features close to that of hair and skin).
   All of the above features have been tested by SGS-CSTC Standards Technical Services Co., Ltd

Note: nanoeTM and the nanoeTM mark are trademarks of Panasonic Corporation nanoeTM X are particulate ions containing hydroxyl radicals whose amount is 10 times that of nanoeTM.

MAIN PARTS IDENTIFICATION

• Air volume display Auto/Low/Med/High

• Filter replacement display
  Filter replacement display   lights up, indicates replace filters.

• Child lock display
  Child lock display  lights up, indicates open child lock.

• PM2.5 concentrations display

  • Display with figure
  • When the measured PM2.5 concentration is lower than 600 µg/m3, the measured value is displayed
  • When the measured PM2.5 concentration is equal to or higher than 600 µg/m3, 600 µg/m3 is displayed.

• nanoeTM X display
  The nanoeTM X icon displays indicates nanoeTM X is being generated. nanoeTM X will be generated in all operation modes except you switch off it. 
  

• Gas pollution level display:

  • Show the air pollution levels detected by gas sensor
    Blue: Indicates clean
    Purple: Indicates slight dirty
    Red: Indicates dirty

• Note: PM2.5 concentrations display and gas pollution level display is for reference only, according to differrent environment, the display will be different.

• The PM2.5 concentrations display may differ when the product is turned on for the first time or when the PM2.5 concentration reaches a stable level by rapid purification

• Two different types of products may show different measured PM2.5 concentrations due to air circulation even in the same space.

  • The air flow around the PM2.5 sensor may cause a difference to the PM2.5 concentration.
  • The PM2.5 concentration may differ when the product is used in the following indoor places
  • Where there are sofas, beds, carpets, detergents, fragrances, cosmetics, perfumes, insects, pets, etc., or where it is humid or smoky.
  • Where it is close to construction sites, roadsides, factories, entrances and exits, windows, ventilators, etc.
  • Where you cook or use a humidifier, spraying agent or other products that may generate steam or fine dust.

SETUP

Before startup

1. Fill in the label with the first date of use.
   
   Notice
   Make sure to read page 2~5 before startup.

2. Remove the HEPA composite filter and the deodorizing filter from the poly bag.

3. Pull the air inlet cover out to remove it by holding the lower part of its handle.
   
   Notice
   Fix the main body in place with your hand when removing the
   air inlet cover.

4. Remove the filters (2 types) separately and horizontally.

Notice
For the first use, take the HEPA composite filter and the deodorizing filter out together with the plastic bag.

3. Remove the HEPA composite filter and the deodorizing filter from the poly bag.  

Notice
Please don’t remove the black net of deodorizing filter.

3. Install filter
   Install the filters (2 types) and inlet cover.
   

4. Install deodorizing filter.
   (There is distinction between inside and outside, with the handle side outward, no distinction between upper and lower)
   

5. Install HEPA composite filter.
   (There is distinction between inside and outside, with the handle side outward, no distinction between upper and lower)

3.  **Install inlet cover.**  

Align the bottom of the air inlet cover with the bottom grooves (two) of the rear cover and snap it in, and then push them in the upper buckles (three) of the air inlet cover.

Notice
Make sure to attach the inlet cover before use.

4. Power-on
   Plug in the power plug.
   (Before plugging, wipe off the water on the power plug and your hands.)
   
   

OPERATION

• **Power Off/On

Turn on or off the product
Press the button to turn the product on, LCD lights on, press the button again to stop operating the product, LCD lights off.
For the first operation, the product starts with the auto mode of air volume.
Notice**

  * If power failure occurs when product is operating, the product will restart automatically from the mode in which it was powered off when the power supply is restored.

• Air volume

Select appropriate air volume for purifying air.
When the product operates, press each time, air volume display on LCD will be changed sequentially as figure below.
If press button, the product can stop operating; press this button again, the product will operate with the mode from last setting.

  *  **Auto**  

Automatically adjust the air volume according to the air pollution detected by sensor, and use appropriate air volume to purify air.

  *  **Low  

Operate quietly in a low speed, but purify air slowly.
**

  *  **Med  

** Purify air in medium speed.

  *  **High  

** Purify air quickly.

• **nanoeTM X

** Turn on or off the nanoeTM X funtion.

  * urn on or off the nanoeTM X funtion.  

Press the button to turn the nanoeTM X function on, the icon displays on LCD

  * press the button again to turn the nanoeTM X function off, the ![Company Logo](https://manuals.plus/wp-content/uploads/2021/12/Screenshot_7-26-300x173.jpg) icon disapears on LCD.

• **Child lock

To prevent child from wrong operating.
Press the button for 3 seconds, the icon displays on LCD, then the child lock is set. With this setting, other buttons are disabled when you press them, with sound “BI-BI-”.
**

  * Press the button for 3 seconds again to cancel child lock setting, the     icon will be disappeared on LCD.

MAINTENANCE

WARNING

 Make sure to disconnect the power plug before cleaning the product.
(Otherwise, the product might operate with the possibility of electric shock or injury.)

Notice

• When using chemically treated cloth, be sure to follow the instructions carefully.

• Do not leave the removed parts unattended.
  (Otherwise, it may cause tripping or damage.)

• Do not operate the product when the deodorizing filter is removed. (Otherwise, the deodorizing filter cannot function while it is removed.)

• Do not use the detergents shown below.
  

• Do not operate the product when the HEPA composite filter is removed.
  (Otherwise, the HEPA composite filter cannot function while it is removed. Dust will be inhaled into product inner parts, and caused the product breakdown. )

• See page 8~9 for disassembly instructions and installation of inlet cover and filters.

Cleaning method

• PM2.5 sensor < about once every 3 months >
  Wipe the dirt off the lens with a dry cotton swab
  Wipe the lens with a dry cotton swab as shown below.

Wipe the lens periodically.
(The sensor may not function normally with accumulation of moisture and smoke from cigarette.)
Do not insert a cotton swab in other parts.
You can use a light in order to see lens clearly.
Be sure to disconnect the power before cleaning.

• Air outlet < about once a month >
  

  • Remove any dust using a vacuum cleaner, and wipe off the dirt with a well wrung-out soft cloth
  • Do not wipe it with a hard cloth or hardly. Otherwise, the surface may be damaged.
  • After the cleaning, dry the body naturally before starting the product.

• Deodorizing filter

• • When there is dust around the deodorizing filter, remove the dust with a vacuum cleaner, etc.
  • Do not wash the filter with water.

• Inlet cover and body < about once a month >
  Wipe off any dust and dirt using a well wrung-out cloth

• * Do not wipe it with a hard cloth or hardly. Otherwise, the surface may be damaged.

  • Wipe the power plug with a dry cloth.
    

• HEPA composite filter < about once every 2 weeks >
  Clean the black side (front side) with a vacuum cleaner, etc

  • Please do not apply too much pressure, otherwise the filter may be damaged. Maintenance is unnecessary for the white side (back side).
  • Do not wash the filter with water.

Filter replacement

(Optional accessories: back cover)

| HEPA composite filter|

Deodorizing filter

---|---|---
Recommended replacement period|  |
When the filter replacement icon displays (about once every 2 years) ※
Conditions| When it is inhales the smoke of six cigarettes every day. (Japan Electrical Manufacturers’ Association JEM1467)

• The time when the filter replacement icon is displayed may vary with the air quality of the ambient environment. The display of the filter replacement icon is set according to the collection of solid particles by the filter. When the performance of the filter is degraded after it has collected a certain amount of solid particles, the icon is displayed as a reminder of replacing the filter. No replacement reminder is set for the icon display in terms of odor.
• Fill in installation date on the label attached with filter, then stick it on product to cover the old date.
• After replacing the filter, plug in the power plug, and press and hold and  at the same time for about 3 seconds. When the filter replacement icon lights off after blinking 3 times or when the product sounds “BI”, the reset is completed. (To replace the filter before filter replacement icon lights on, please observe the above procedure to reset the filter replacement period; otherwise, the indicator may not be able to correctly indicate the replacement period of the new filter. Do not perform the above procedure if the filter is not replaced; otherwise, the filter replacement period is reset.)

Notice

• The filter which needs to exchange cannot be used again even it is cleaned, please dispose the used filter as non-flammable garbage.
• If the product is used in a room (especially hotel) with strong odor such as aromatic smell, cigarette smoke or barbecue smell, these odors may adhere to the filter. When the adsorption capacity of filter reaches saturation, odor will also be blown out again with the wind because of excess adsorption. When there is above situation, please clean the HEPA composite filter. If the situation persists, please replace the HEPA composite filter and deodorizing filter, even if the filter replacement icon is off. In addition, if often used in a room with strong odor, please open the windows to ventilate the room regularly.

When idle for a long time

1. Disconnect power plug after turning off the product. (The product still consumes power even at rest.)
2. Maintain the product as usual.
3. Put the product into poly bag and carton, and keep it in a dry place. (If you overturn it or keep it flat, product malfunctions may occur.)

FURTHER INFORMATION

About gas sensor •PM2.5 sensor

The sensor detects air pollutants and shows the pollution level by the PM2.5 concentrations. In auto operation, the product can optimize the air volume for purifying the air according to the detected pollutants.

Sensor

| Sensing scope|

May detect

---|---|---

Gas sensor

|

• Odor from cigarettes, incense, cooking, pets
• Cosmetics, alcohol, sprays, etc.

|

• Humidity (water vapor), oil
• The wind generated when a door  s opened or closed, or sudden temperature changes

PM2.5 sensor

|

• PM2.5 (0.3 µm~2.5 µm particles)
• Indoor dust (dust, dead bodies and excreta of ticks, mold spores, pollens, etc.)
• Smog (cigarettes, incenses, etc.)

|

• Oil, fog-stated water drip

Notice

• The sensor’s operation may vary depending on the indoor airflow condition if a heater is placed near the product in a room.
• The sensor is not designed to detect bacteria and viruses
• The gas sensor and PM2.5 sensor do not operate when the operation is set to “Off”.

About nanoeTM X

• Conditions for nanoeTM X generation
  nanoeTM X is generated by using the air in the room. Therefore, due to the differences in temperature and humidity nanoeTM X may not be generated stably Room temperature: about 5 ℃～35 ℃ (dew-point temperature: 2 ℃ or above) Relative humidity: about 30%～85%

• When nanoeTM X is generated, small amount of ozone will be released. However, the quantity will be far less than the level in natural environment such as forest, and not be harmful to human beings.

About brightness reaction

The product detects the indoor brightness by the light sensor and adjusts the brightness of the LCD accordingly. When the indoor ambient light gets dark, the LCD dims accordingly.

FAQ

Please confirm the following before you put questions forward or send the product for repair.

• Q1: Why is a “jee” sound from the emission outlet?
  A: There is a slight sound when nanoeTM X is being generated. Depends on the environment and operation mode, the sound may be a bit loud or inaudible but it is not abnormal.

• Q2: Why does the PM2.5 figure remain unchanged?
  A: Such problems may occur because of the difference in sensitivity of PM2.5 sensor.

• Q3: Why will air outlet blow out the odor?
  

  • A: The adsorption capacity of filter reaches saturation, odor will also be blown out again with the wind because of excess adsorption.
  • A: The filter has not been cleaned after getting dirty.

• Q4: Why has the gas pollution level display never changed?
  A: Such problems may occur because of the difference in sensitivity of PM2.5 sensor.

TROUBLESHOOTING

If a problem is encountered, please investigate it by going through the following items.
If the problem still persists, please disconnect the power plug and contact the dealer for repair.

Possible situation

|

Please confirm the following

---|---
1 Automatic operation cannot be stopped|

• When the setting is “Auto”, the product will still operate with low air volume even if the air in the room is clean.

2 Polluted air is difficult to be removed|

• Is the filter dirty?（P.12）
  • Please clean it. If the situation persists, replace the filter with a new one.

3 The air volume is small

1. The odor from the product is unpleasant

|

• Is the body, inlet cover or filter dirty? (P.12)

  • If the problem persists after the filter is cleaned, please replace it with a new one.
    (The harmful carbon monoxide generated by cigarette cannot be removed)

• Has the product ever been used in a room with strong odor?
  If the product is used in a room with strong odor such as aromatic smell, cigarette smoke or barbecue smell, the filter replacement period may be shortened.

  • If you use the product in such environments, it is recommended to open the air ventilation system or open the windows to ventilate the room at the same time. If there is still strong odor to be blown out after the maintenance , please replace the filter, even if the filter replacement icon does not light on.

If any of the following cases occur, please contact the dealer immediately for repair.

LCD displays “F10”

|

• Product may be out of order.
  • Please disconnect the power plug and contact the dealer for repair.

---|---

SPECIFICATIONS

Model No.

| F-PXU70M
---|---

Power supply

| 220 V-240 V~ 50 Hz

220 V-230 V~ 60 Hz

Air volume settings| High| Med|

Low

Power consumption (W)※1

| 36| 10.5| 6.5
Floor area capacity ※2|

Up to 95 m 2 in a standard household room

Power cord length

| 2.0 m
Product dimension|

362 mm x 280 mm x 560 mm (WxDxH)

Product weight|

8.0 ㎏

1. The power consumption is about 0.5 W when the operation is set to “Off” (With the power plug inserted).
2. Floor area capacity is based on NRCC 54013, under the condition of high speed.
   Note: This product cannot remove hazardous substances such as carbon monoxide from the cigarette smoke.

OPTIONAL ACCESSORIES

Replacement HEPA composite filter Part No F-ZXTP70Z

Replacement deodorizing filter Part No.: F-ZXTP70Z F-ZXTD70Z

Warranty card attached (only for Australia)

Thank you very much for purchasing this Panasonic product.
Please read these operating instructions carefully before operation and maintenance.
Also, be sure to read the “SAFETY PRECAUTIONS” section (P.2~4) before use. Failure to comply with instructions could result in injury or property damage.
Make sure that the correct information is written on the warranty card, including the date of purchase and the name of the distributor. Keep the warranty card in a safe place along with the operating instructions for future reference.

Panasonic Corporation
Web Site: http://www.panasonic.com
©Panasonic Corporation 2021
Issue date: 08/2021
P0821-0 PXU7M8950 C

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>