tuya MAA-6068P Smart Wi-Fi Lock Owner’s Manual

: August 23, 2024
: Tuya

Table of Contents

tuya MAA-6068P Smart Wi-Fi Lock
FAQs
PRODUCT NOTICE AND PRODUCT MAP
INSTALLATION INSTRUCTIONS
HOW TO USE YOUR SMART LOCK
FUNCTION AND OPERATION
” Or directly press the “Set” button on the rear panel enter the
Read User Manual Online (PDF format)
Download This Manual (PDF format)

tuya MAA-6068P Smart Wi-Fi Lock

FAQs

Q: How do I unlock the device in combination unlock mode?

A: In combination unlock mode, any two groups of non-administrator unlock information with different numbers can be combined to unlock the device.

Q: What happens if the device is unlocked in a normal state?

A: If the device is unlocked in the normally open state, pressing any key will lock it again.

PRODUCT NOTICE AND PRODUCT MAP

Dear users, Hello! Thank you for using this smart lock. Please check the product list carefully before you install and use this product, read the installation instructions, and install the product according to these installation instruction. If it is not installed according to this installation instruction, the direct or indirect product problem will be caused., as with other hazards and losses, our company does not assume any responsibility.

The above pictures are for reference only, please refer to the actual product.

INSTALLATION INSTRUCTIONS

The door lock, lock body and handle can be used for different opening doors, which can be reversed left and right. Please select different lengths of mounting accessories according to the thickness of the door.

0PENING DIRECTION MEASURING THE LENGTH AND WIDTH OF THE GUIDE PIECE

INSTALLATION STEPS

Place the lock body in the door frame.
Lock body plug-in hook up and down
Tighten the four fixing screws on the lock body.
According to the thickness of the door, install the connecting screw, adjust the handle to the door opening direction, fix the directional screw, and screw the square hole into the position of the handle.
The square bar is inserted into the lock body, from the outside of the door to the inside of the door
Put the power cord on the front panel into the door and fasten the front panel.
Connect the front and rear panel wiring, put the wire into the door, and do not press the wire.
Fix the upper and lower screws.
With the battery installed, the smart lock is installed successfully.
Internal and external handles, safety knobs, and mechanical keys Check that the components are connected properly.

HOW TO USE YOUR SMART LOCK

Fingerprint unlock
Password Unlock
- Light the keyboard with your fingers
- Enter the entered password and press # to n n confirm. The tone prompt lock is on
- Turn the handle down to unlock.
No need to worry about the password being voyeur Anti-peeping passwords, before and after the correct password Random input, not afraid to peep and peek, all eyes Can also be calm.

MECHANICAL KEY OPEN

If there is an emergency such as a forgotten password, the battery is exhausted or the system is not working, you can use the spare mechanical key to unlock it.

DOOR LOCK

External lock outdoor handle-up rotation lock
internal lock indoor handle up rotation lock
internal anti-lock button for anti-locking.

FUNCTION AND OPERATION

Initial state

The factory default state password is “123456” to open the door. After entering the administrator information, the initial password “123456” will be deleted automatically.o

General rules of operation

We will enter the management fingerprint and management password collectively into the administrator information.

” #” The key is the confirmation key or the menu function key
” *” The key is the clear key/back key. When entering the password,
- click to clear the previous input, and long press to clear the input.

Enter door lock function management

In the initial state, press “ + #” after operating the touch screen or directly press “Set” on the rear panel set key to prompt entry administrator, voice broadcast: “Add administrator” “Please enter to add fingerprint card or password “. After successful addition, automatically enter the door lock management function, voice broadcast: “Administrator Authentication Successful” “1 Add User” “2 Delete User” “3 Door Lock Setting” “4 Add Administrator”. Press the “#” key to repeat the announcement after the voice has been recorded to the administrator, Every time you enter the door lock management function, you only need to operate the touch screen and press “ +

” Or directly press the “Set” button on the rear panel enter the

administrator verification state. Voice announcement after operation: “Please verify the administrator”, the administrator is successfully verified, and the door can be locked function management, voice broadcast: “Administrator verified function “1 add user” “2 delete user” “3 door lock settings” “4 add administrator” .Press “#” key to repeat voice announcement

Administrator settings

Administrator settings include entering administrator, deleting administrator, administrator information can be entered into fingerprint, Password, and card, after entering the door lock function management, follow the voice prompts to operate ..

Enter administrator information

Speech order :

Voice broadcast: “Administrator successfully authenticated” “1 add user” 2 delete user” “3 Door Lock Settings” “4 Add Administrator” Select 4 Add Administrator
Voice broadcast: “Please enter the fingerprint, card or password to be added” Enter the entryAdministrator information, and follow the voice prompts
Voice broadcast: “Ignore” Note: During the entry process, you cannot enter the information that has already been entered. The number of passwords is 6 to 12 digits.

Delete administrator information

Delete by number
Speech order :
Voice broadcast: “Administrator successfully authenticated” “1 add user” “2 delete user” “3 Door Lock Settings” “4 Add Administrator” Option 2 delete user
Voice broadcast: ”Please enter the number, fingerprint, card, password or remote control to be deleted ” Enter the administrator number to be deleted, and press “#” to confirm”
Voice broadcast: “”Delete number XXX, please confirm” Press “#” to confirm deletion Administrator, press “*” to give up”
Voice broadcast: “ignore”

USER SETTINGS
Settings of ordinary users include input of ordinary users, modification of ordinary users and deletion of ordinary user information. Ordinary user information can be a card, password, or remote control (optional function). After entering the door lock function management, press the display option prompt to operate.

Enter general user information

Speech order :

Voice broadcast: “Administrator successfully authenticated” “1 add user” “2 delete user” “3 Door Lock Settings” “4 Add Administrator” Select 1 Add user.
Voice broadcast: “Please enter the fingerprint, card or password to be added” Enter the entryAdministrator information, and follow the voice prompts
Voice broadcast: “ignore”

Note : During the entry process, you cannot enter the information that has already been entered. The number of passwords is 6 to 12 digits.

Delete normal user information

Delete by number

Speech order :
Voice broadcast: “Administrator successfully authenticated” “1 add user” “2 delete user” “3 Door Lock Settings” “4 Add Administrator” Option 2 delete user
Voice broadcast: ”Please enter the number, fingerprint, card, password or remote control to be deleted ” Enter the administrator number to be deleted, and press “#” to confirm”
Voice broadcast: “Delete the number XXX, please confirm “press” # ” to confirm the deletion of the specified user, Press “*” to give up
Voice broadcast: “Ignore”

Delete all users

Speech order:

Voice broadcast: “Administrator successfully authenticated” “1 add user” “2 delete user” 3 Door Lock Settings” “4 Add Administrator” Option 2 delete user
Voice broadcast: ”Please enter the number, fingerprint, card, password or remote control to be deleted “Enter 000, and press” # “to confirm”
Voice broadcast: “Delete all I users, please confirm “Press” # “to confirm deletion of all users, and press” * “to abandon”
Voice broadcast: “Ignore”

DOOR LOCK SETTINGS

Function options include function settings, volume adjustment, language settings, time settings, access door lockFollow the voice prompts after function management V

Function settings

Voice broadcast order:

Voice broadcast: “1 Function setting ” ” 2 volume adjustment ” ” 3 language setting ” “4 time settings” Select 1 function setting, and follow the voice prompts ”
Voice broadcast: ”1 Turn on (or turn off) normally open mode, “2 turns on (or turn off) double verification”,
turn on (or turn off) anti-pry alarm”, “4 turns on (or turn off) silent mode” 3: Voice broadcast: “ignore”

Note Each function is set to be on or off, if the last time is off, the voice prompt is turned on, otherwise the prompt is turned off.
After the normally open mode is turned on, each time the lock is unlocked, it enters the normally open state, and press any key to lock
In combination unlock mode, any two groups of non-administrator unlock information with different numbers can be combined to unlock

Volume adjustment

Voice broadcast order:
Voice broadcast: ” 1 function settings” “2 volume adjustments” ” 3 language settings” “4 time settings” Select 2 voice adjustments and follow the voice prompts
Voice broadcast: “1 volume down” “2 volume up”
Voice broadcast: ignore

Language settings

Voice broadcast order:
Voice broadcast: “1 function settings” “2 volume adjustment””3 language settings” “4 time settings” Select 3 language settings, and follow the voice prompts
Voice broadcast: “1 Chinese” “2 English”
Voice broadcast: ignore

Time setting

Voice broadcast order:
Voice broadcast:”1 function setting” “2 volume adjustment” ” 3 language setting” “4 time setting” Select the time setting, and follow the voice prompts
Voice broadcast: ignore

RESTORE FACTORY SETTINGS

Long press the ” Erase” button on the rear panel for 5 seconds, the system will enter the state of factory reset All unlocking information and records will be cleared. After success, the initial password will be restored to 1 23456 (For unlocking administrator verification).

Other instructions

Enter the wrong password more than 5 times in a row, lock the keyboard for 1 minute, and the system will not respond to any operation within 1 minute.
Password anti-prying function: when opening the door, enter the password as follows:
- - - - correct password ( is any number); You can add some extraneous codes before and after the password, and then press# to confirm. The password must be included in the input.
If there is no operation for more than 10 seconds, the system will exit automatically
After the voltage is lower than 4.8v, the lock will automatically alarm every time it opened. After the alarm, the lock can be opened for 200 times
In the normally open mode, each unlock system will broadcast the voice; “Normally open mode”. When the door lock is often opened, the inclined tongue will also have such a hint every time it is touched.