Spectrum Brands 450126VHC Wave Plus Lock Version II User Manual
- June 5, 2024
- Spectrum Brands
Table of Contents
Spectrum Brands 450126VHC Wave Plus Lock Version II User Manual
Welcome to the Kwikset family!
This guide will get you up and running with your new [NEED NAME] Lock.
If you have any issues, please visit our support center: kwikset.com/[need- url] or call us at 1-800-327-5625.
Parts in the box
Required tools
Installation
Remove your existing deadbolt
1. Install the latch
2. Install the strike
3. Install the exterior assembly
4. Install the interior assembly
5. Perform the door handing process
Smart home system setup
Add the lock to your smart home system
At a Glance
Troubleshooting
If you have any issues, please visit our support center: kwikset.com/need- url or call us at 1-800-327-5625.
Network Information
Removing the lock from the network
Follow your smart home system’s instructions to remove the lock from the
network. When prompted by the system, press button “A” on the lock interior
once.
Z-Wave® System Notes
This product is a security enabled Z-Wave Plus product and must be used with a Security Enabled Z-Wave controller to be fully utilized. Z-Wave is a “Wireless mesh network,” and results may vary based on building construction and communication path.
To assure interoperability, each Z-Wave product must pass a stringent conformance test to assure that it meets the Z-Wave standard for complete compliance with all other devices and controls. The Z-Wave identity mark assures consumers, integrators, dealers and manufacturers that their products will reliably perform with any other Z-Wave device. And, regardless of the vendor, always powered nodes may act as a repeater for Kwikset/Weiser/Baldwin products.
Z-Wave Configuration and Association Parameters are available on the [NEED NAME] page at www.kwikset.com.
Important Safeguards
- Read all instructions in their entirety.
- Familiarize yourself with all warning and caution statements.
- Remind all family members of safety precautions.
- Always have access to your lock’s standard key.
- If using the Auto-Lock features, make sure you have your smartphone or standard key with you to prevent locking yourself out.
- Familiarize yourself with all error notifications.
- Replace low batteries immediately.
- Dispose of used batteries according to local laws and regulations.
WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualified locksmith or other security professional.
Regulatory Compliance
This product complies with standards established by the following regulatory bodies:
- Federal Communications Commission (FCC)
- Industry Canada
FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: ( 1 ) this device may not cause harmful
interference, and ( 2 ) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT! Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions: ( 1 ) This
device may not cause interference, and ( 2 ) This device must accept any
interference, including interference that may cause undesired operation of the
device.
Read More About This Manual & Download PDF:
References
- Door Locks, Door Hardware, Smart Locks & Smartkey Technology | Kwikset
- Door Locks, Door Hardware, Smart Locks & Smartkey Technology | Kwikset
- Drilling Instructions | Kwikset
- Door Locks, Door Hardware, Smart Locks & Smartkey Technology | Kwikset