PARKSIDE IAN 469174_2310 Wall Mounted Hose Reel Instruction Manual
- August 20, 2024
- PARKSIDE
Table of Contents
PARKSIDE IAN 469174_2310 Wall Mounted Hose Reel
Product Information
Specifications
- Model : IAN 469174_2310
- Type : Wall-mounted Hose Reel
- Language Options : DE/AT/CH, GB/IE, FR/BE, NL/BE, PL, CZ, SK, ES, DK, IT, HU
- Version : V2.0
Product Usage Instructions
Introduction
Before starting, unfold both pages containing illustrations to familiarize
yourself with all the functions of the device.
General Safety Instructions
Read and follow all safety instructions provided in the manual to ensure
safe operation.
Initial Setup
Follow the instructions for initial setup and ensure all components are in
place.
Assembly
Refer to the assembly section in the manual and follow step-by-step
instructions to assemble the wall-mounted hose reel correctly.
Operation
Learn how to operate the hose reel efficiently by following the operating
instructions provided.
Cleaning, Maintenance, and Storage
Regularly clean the hose reel, perform maintenance tasks as recommended,
and store it properly when not in use.
Disposal
Follow the guidelines for proper disposal of the product when necessary.
Warranty and Service
Refer to the warranty information for details on coverage and service
options available.
List of pictograms used
| DANGER! This symbol and signal word denotes a hazard with a high risk, which, if not prevented, could result in death or serious injury.|
| WARNING! This symbol and signal word denotes a hazard with a medium
risk, which, if not prevented, could result in death or a serious injury.
| CAUTION! This symbol/signal word denotes a hazard with a low risk,
which, if not prevented, could result in a minor or moderate injury.|
| NOTE! This signal word warns against potential property damage.
| Read the assembly instructions and instructions for use!| | Warning!
The danger of electric shock!
| Observe the warnings and safety instructions!| | UV-resistant.
| Risk of fatal injury and accidents for infants and children!| | The SGS seal confirms that the product is safe when used as intended. The “GS” symbol stands for “tested safety”.
Products with this sign are by the requirements set out by the German Product Safety Act (ProdSG).
| Not suitable for drinking water.| | Dispose of the packaging and product in
an environmental- ly-friendly manner!
| Weather-resistant.|
| The product meets the applicable European product-specific directives.
| Safety notices Instructions for use| | Do not allow the hose to re-ravel by itself. Carefully guide it back into the housing.
Introduction
Congratulations on the purchase of your new product. You have chosen a high- quality product. The assembly instructions and instructions for use are a part of the product. Please carefully read these assembly instructions and instruc- tions for use before use and observe all instructions. These instructions contain important information about installation, settings, and care. Please keep these assembly instructions and instructions for use and pass them on to any future owner.
Intended use
This product is exclusively designed as a hose reel inside a closed hose box with automated raveling. In addition to the spray nozzle, other devices that use water can be connected to the hose, for exam-ple sprinklers, irrigation systems, and high-pressure washers. It is only intended for private, non- commercial use. Only use the product as described in these instructions for use. Any other use is considered improper use and may result in property damage or personal injury. This product is not a toy. The manufacturer and retailer assume no liability for damages due to improper or incorrect use.
Parts description/scope of delivery
- 1 wall bracket
- 1 axle bolt
- 1 hose box
- 1 carrying handle
- 1 limit stop
- 4 wall anchors
- 4 screws
- 1 split pin
- 1 irrigation hose
- 1 spray nozzle
- 1 hose connector with water stop for spray nozzle
- 1 connection hose
- 1 hose connector for tap
- 1 tap connector
- 1 reducer
- 8 washers*
- 4 threaded bolts/hex wood screws 18 4 spring lock washers 19 1 nut Assembly instructions and instructions for use Not included
Technical data
Model : WU9927170-8
- Hose box with wall bracket Dimensions ( W x H x D) : approx. 38.5 cm x 19 cm x 36.5 cm
- Weight (without heavy-duty anchors): approx. 6.3 kg (empty) approx. 8.13 kg (with water in the hose)
- Swivel range: horizontal approx. 180°
- Material: plastic, weather-resistant
Hoses
- Length Irrigation hose: approx. 20 m
- Connection hose: approx. 2 m
- Diameter: 15 mm (external), 11 mm (internal)
- Working pressure: max. 10 bar
- Material: PVC fabric tube
General safety information
WARNING : READ ALL SAFETY NOTICES AND INSTRUCTIONS! KEEP ALL SAFETY INFORMATION AND INSTRUCTIONS FOR FUTURE REFERENCE!
DANGER! DANGER OF ELECTRIC SHOCK! Faulty installation or use can result in electric shock:
- Make sure that you do not damage any power lines during installation.
- Never aim the water jet at elec-trical equipment.
- Never aim the water jet at people or animals.
WARNING
- Dangers to children and persons with reduced physical, sensory, or mental capabilities (for example, partially disabled people, elderly people with reduced physical and mental faculties) or a lack of experience and knowl-edge (e.g. older children).
- Ensure that this product is used exclusively by persons who are at least 16 years of age, who are in full possession of their physical and mental faculties, and who have read and understood these operating instructions. Any other person may only use the product under the supervision of an authorized person.
- Keep children away from the product. Do not allow children to use or play with the product.
- Never leave the product unattended whilst in use.
- Keep children away from the work area during assembly. This product has screws and other small parts. These could lead to suffocation if they are swallowed or inhaled. Do not allow children to play with the packaging film. Children can get entangled in it whilst playing and suffocate.
WARNING: RISK OF INJURY! Faulty installation or use can result in injuries. Make sure that all parts are un-damaged and correctly assembled.
- Regularly check the water pressure to prevent water from leaking under high pressure and causing injury. Do not aim the water jet at people or animals.
- Never drink the water that you transport with the product. The product is not suitable for drinking water. The product is intended for carrying water from installations in fixed locations.
- You cannot use it to transport other liquids. Only lay the unraveled hose flat on the ground. Avoid loops that stand up. Loops are trip hazards and can cause accidents.
- Do not allow the hose to re-ravel by itself. Carefully guide it back into the housing.
- Do not let go of the hose unless the automatic stop function is engaged.
- Do not open the housing of the product. The springs are pre-loaded, they can spring back.
CAUTION! DANGER OF SLIPPING!
- When the ground is wet, you could slip on the ground and injure yourself.
- Ensure that the ground near the product is kept as dry as possible. Turn the tap off when the product is not in use.
NOTE! RISK OF DAMAGE! Improper use of the product may result in damage .
- Make sure that you do not damage any cables, power lines, and water pipes during installation. Check the installation area with a cable detector before drilling.
- To avoid frost damage, take the product off the wall in winter and store it dry.
- Do not take the hose around corners or edges and do not move it along pointed or sharp-edged objects. The resulting damage may lead to leakages.
- Do not put the hose in areas where vehicles are known to drive. Driving over the hose may cause it to split.
- Never remove any screws from parts of the housing.
- Make sure the hose does not re-ravel by itself. This could result in damage.
- Never block the hose end with your fingers or other objects during use.
- Installation must only be performed by skilled persons.
- Discontinue using the product if the plastic parts of the product are cracked or deformed. Always replace damaged parts with genuine spare parts.
Initial use
Check the product and contents
NOTE! RISK OF DAMAGE!
Opening the packaging carelessly with a sharp knife or other sharp objects
could quickly damage the product. Be very careful when opening the packaging.
- Remove the product from the packaging.
- Verify that the contents are complete (see chapter “Parts description/scope of delivery“).
- Check to see if the product or the individual parts are visibly damaged. If this is the case, do not use the product. Please contact your retailer.
Basic cleaning
- Remove the packaging material and all protective film.
- Before first use, clean all parts of the product as described in the “Cleaning and Maintenance” section.
Installation
NOTE! RISK OF DAMAGE! Improper use of the product may result in damage.
- Make sure that you do not damage any cables, power lines, and water pipes during installation. Check the installation area with a cable detector before drilling.
Selecting the installation location
- Choose a stable weight-bearing installation location.
- Be aware of the weight of the product including the water in the hose (see chapter “Technical data”).
- Choose an installation location where the full 180° swivel range of the hose box 3 can be used ( see fig. A ).
- Measure the distance to the tap so that the connection hose 12 can be connected with slack ( see fig. B ).
Preparing the installation materials
For installation on a concrete wall or brickwork
(see fig. C)
- For unplastered walls and plaster thicknesses of up to 10 mm, please use the screws 7 and wall anchors 6.
- For plaster thicknesses of more than 10 mm, please use suitable heavy-duty anchors sold by specialist retailers.
For installation on board walls
(see fig. D)
- Use the following mounting material:
- 4 threaded bolts 17 * M8; Length: 20 mm + board thickness
- 8 washers 16 *
- 4 spring lock washers 18 *
- 4 nuts 19 *
*Not included
For installation on a wooden post (the wooden post must have a minimum transverse section of 100 x 100 mm)
(see fig. E)
- Use the following mounting material:
- 4 hex wood screws 17 * Ø 8 mm × 100 mm
- 4 washers 16
- 4 spring lock washers 18
* Not included
How to install
- Pull out the axle bolt 2 and remove the wall bracket 1 from the hose box 3 ( see fig. F ).
- Draw bore holes on the wall ( see fig. G ).
- Install the wall bracket 1. The wall bracket must be attached vertically.
- For concrete walls and brickwork, follow Fig. C.
- For board walls, please follow Fig. D.
- For wooden posts, please follow Fig. E.
- Mount the hose box 3 on the wall bracket 1 ( see fig. H). Hold the hose box by the carrying handle 4 . Guide the hose box into the wall bracket until the axle holes line up. Guide the axle bolts 2 completely into the axle holes.
- Connect the tap connector 14 to the tap ( see fig. I ). Depending on the size of the tap’s connecting thread, turn the reducer 15 into the tap connector.
- Connect the hose connector for the tap 13 with the connection hose 12 on the tap connector 14 ( see fig. J). The product is ready to use.
Removal
- To remove the product, follow the installation instructions in reverse.
Operation
Unravelling the hose
- Pull the irrigation hose 9 out of the hose box 3 to the desired length ( see fig. K). ****
- Reduce the tension. Due to the product’s STOP function, the irrigation hose briefly retracts until it is held by the retraction block.
- Open the tap.
- Open the spray nozzle 10 ( see fig. L ). ****
Note : The STOP function makes it possible to stop the hose at any desired point. This makes it possible to work without consistently pulling the irrigation hose. Briefly pull on the irrigation hose 9 to release the retraction block.
Re-raveling the hose
RISK OF INJURY AND DAMAGE! If the irrigation hose is not guided, the spring tension of the automated raveling system can cause it to spin around and lead to injury and property damage. Always guide the irrigation hose by hand. Ensure that no other people are nearby when traveling. Never reach inside of the housing.
- Close the spray nozzle 10.
- Close the tap.
- Open the spray nozzle 10 to release the water pressure. Close the spray nozzle.
- Hold the irrigation hose 9 by the spray nozzle 10. Briefly pull on the irrigation hose to release the attraction block. Guide the irrigation hose by hand while it automatically rolls up to the limit stop 5 into the hose box 3 ( see fig. M ). ****
- Swivel the hose box 3 towards the wall to save space (see fig. A).
Connecting other devices using water
- To connect other devices that use water, remove the spray nozzle 10 from the hose connector with the water stop 11 ( see fig. N). The water stop integrated into the hose connector will prevent water from flowing backward.
Winter storage
Protect the product against frost. The freezing residual water in the hose will expand and may cause damage.
- Disconnect the connection hose 12 from the tap.
- Completely drain the connection hose 12. Make sure that the irrigation hose 9 is also emptied.
- Allow all parts to dry fully.
- Remove the hose box 3 from the wall bracket 1 (see fig. F).
- Store the hose box 3 so that it is protected from frost.
Cleaning, maintenance, and storage
NOTE! RISK OF DAMAGE!
Improper use of the product may result in damage to the product.
- Do not use aggressive cleaning agents or sharp or metal cleaning tools such as knives, rigid scrapers, etc. These can damage the surfaces.
Cleaning
Clean all parts with a lightly moistened cloth.
Maintenance and care
After every use:
Re-ravel the irrigation hose 9 to the limit stop 5 after each use to release
the pressure on the retaining spring.
Monthly and after each winter:
Regularly check the hoses for tears, brittleness, and other signs of wear.
Have defective hoses replaced by the manufacturer.
Storage
- All parts must be completely dry before storage.
- Always store the product in a dry location.
- Protect the product against direct exposure to sunlight.
- Store the product securely locked away out of the reach of children at a storage temperature between 5 °C and 20 °C (room temperature).
Disposal
The packaging is made from environmentally-friendly materials which can be disposed of through your local recycling facilities. Please contact your local municipality or city administration for information on how to dispose of the worn-out product. The products incl. accessories and packaging materials are recyclable and are subject to extended producer responsibility. Dispose of them separately, following the illustrated Info-tri (sorting information), for better waste treatment. The Triman logo is valid in France only.
Warranty and service
- The product has been manufactured to strict quality guidelines and meticulously examined before delivery. In the event of material or manufacturing defects, you have legal rights against the retailer of this product. Your legal rights are not limited in any way by our warranty detailed below.
- The warranty for this product is 3 years from the date of purchase. The warranty period begins on the date of purchase. Keep the original sales receipt in a safe location as this document is required as proof of purchase.
- Any damage or defects already present at the time of purchase must be reported without delay after unpacking the product.
- Should the product show any fault in materials or manufacture within 3 years from the date of purchase, we will repair or replace it – at our choice – free of charge to you. The warranty period is not extended as a result of a claim being granted. This also applies to replaced and repaired parts.
- This warranty becomes void if the product has been damaged, used, or maintained improperly.
- The warranty covers material or manufacturing defects. This warranty does not cover product parts subject to normal wear and tear, thus considered consumables (e.g. batteries, rechargeable batteries, tubes, cartridges), nor damage to fragile parts, e.g. switches or glass parts.
Customer service
Conmetall Meister GmbH Oberkamper Straße 39 42349 Wuppertal GERMANY
Tel.: +49 (0) 202 24750 430/431/432 (Call charges are dependent on the
land-line tariff of your phone provider)
Tel.: +800 34 99 67 53 (from abroad) Email : meister-
service@conmetallmeister.de
IAN 469174_2310
Please have your receipt and the item number (IAN 469174_2310) ready as
your proof of purchase when enquiring about your product.
Original EU declaration of conformity
We declare under our sole responsibility that the following product …WALL- MOUNTED HOSE REEL 20 m
IAN 469174_2310 WU9927170-8:
- complies with all the provisions of the applicable directives: 2006/42/EG (MD)
- Applied harmonized standards: DIN EN ISO 12100:2010
Wuppertal,…….15.01.2024
Conmetall Meister GmbH Oberkamper Str. 39 42349 Wuppertal GERMANY Art.-No.
WU9927170-8
Frequently Asked Questions
Q: How do I mount the hose reel on the wall?
A: To mount the hose reel on the wall, follow the detailed instructions
provided in the assembly section of the manual. Ensure you use appropriate
tools and hardware for secure installation.
Q: How should I store the hose reel when not in use?
A: When not in use, clean the hose reel, ensure it is dry, and store it in
a cool, dry place away from direct sunlight to prolong its lifespan.
Q: Can I use this hose reel for hot water?
A: It is recommended to use this hose reel for cold water only. Using hot
water may damage the product and void the warranty.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>