cudy LT500D Dual Band Unlocked 4G LTE Modem Router Installation Guide

: June 2, 2024
: cudy

Table of Contents

LT500D Dual Band Unlocked 4G LTE Modem Router
LED and Button
Customize The 4G Router
Need Help?(EN)
Declaration of Conformity
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LT500D Dual Band
Unlocked 4G LTE Modem Router
Installation Guide

LT500D Dual Band Unlocked 4G LTE Modem Router

Make sure the antennas are installed properly and place vertically as the picture below.
With the gold contacts facing down, gently slide the nano SIM card into the slot until you hear a click sound.
Connect power adapter and turn on the router. Waiting for 2 minutes for it to start.
Check the status of the system LED.
When the system LED turns solid blue, it means the router is connected to the 4G cellular network.
If the system LED turns to solid purple, it means the router is connected to 2/3G cellular network.
If the system LED turns to solid red, please follow the instructions of Customize the 4G Router.

LED and Button

Name	Status	Indication
System LED	Solid On	Red
Blue	4G or WAN Internet is connected
Purple	2/3G is Connected
Flashing	Red	System is starting up
Blue	WPS is in progress
Red-Purple-Blue	Software Upgrading
Ethernet LED	Off	Power adapter is not connected to the device.
On	The corresponding Ethernet port is connected.
Off	The corresponding Ethernet port is not connected.
Button	WPS	Press and hold 1 second to enable the WPS function.
Reset	Press and hold this button for about 6 seconds to reset the router to

its factory default settings.

Customize The 4G Router

Connect the router via an Ethernet cable or Wi-Fi. Network name and password is printed on the bottom of the router.
Note: For LT450 and LT500, the device will create two WiFi signals, 2.4GHz WiFi network name is Cudy-XXXX, 5GHz WiFi network name is Cudy-XXXX-5G.
Launch a web browser and enter http://cudy.net/(or http://192.168.10.1/) in the address bar, use admin as password to login.
The page below would pop up if your SIM card needs PIN to unlock. Please enter your PIN and click Save & Apply, then wait 15 seconds to connect to the Internet.
Then please check 4G information card of the status page. If the status is connected, means connected to the internet successfully.
If 4G is not connected, or if you want to customize the router yourself, click “Quick Setup” and follow the step-by-step instructions to conﬁgure the router.

Note

If you are not sure about APN parameters, please contact your internet provider.
If you meet any other problems, don’t hesitate to contact our technical support team: support@cudy.com

Need Help?(EN)

Q1. What shou Q1. What should I do if I cannot access the web management page? ld I do if I cannot access the web management page?****

– A1: If the computer is set to a static IP address, change its settings to obtain an IP address automatically.
– A2: Make sure http://cudy.net/ or http://192.168.10.1/ is correctly entered in the web browser.
– A3: Use another web browser and try again.
– A4: Reboot your router and try again.
– A5: Disable and enable the active network adapter in use.

Q2. How do I restore the router to its factory default settings?****

– A1: With the router powered on, press and hold the RESET button for 6 seconds and then release it, Wait the router to reset.
– A2: Log into the web management page of the router, and go to Advanced Settings >Reset , click Perform Reset and wait until the reset process is completed.

Declaration of Conformity

Cudy hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2009/125/EC and 2011/65/EU.
The original EU declaration of conformity may be found at http://www.cudy.com/ce.