FORTIN EVO-ONE Push Start Remote Starters and Alarm Systems Installation Guide

August 21, 2024
FORTIN

FORTIN EVO-ONE Push Start Remote Starters and Alarm Systems

Specifications:

  • Model: EVO-ONE
  • Date: 02/2019
  • Manufacturer: FORTIN.CA
  • Compatibility: Vehicles – SUBARU Crosstrek Impreza
  • Push-to-Start: Yes
  • Firmware Version: 93.[01] (minimum)

Product Usage Instructions

Installation:

  1. Ensure the vehicle is compatible with the EVO-ONE module, suitable for SUBARU Crosstrek Impreza.
  2. Check and update the firmware version using the FLASH LINK UPDATER or FLASH LINK MOBILE tool if needed.
  3. Install required parts like the hood pin switch and diodes as specified in the manual.

Connections:

  1. Make necessary connections as per the wiring diagram provided in the manual.
  2. Connect to the designated terminals for ignition output, CAN bus, foot brake activation, and other required functions.

Programming:

  1. Program the bypass options and unit settings based on your vehicle requirements.
  2. Set the function A11 to OFF if the vehicle can be remote started with the hood open.

Usage:

  1. Use the push-to-start feature to start your vehicle conveniently.
  2. Ensure all connections are secure and functioning properly before using remote start functions.

FAQ:

  1. Q: What should I do if I encounter issues during installation?
    A: If you face any difficulties during installation, please contact a qualified technician for assistance to avoid any damage to your vehicle.

  2. Q: Can I use the EVO-ONE module with vehicles other than SUBARU Crosstrek Impreza?
    A: The EVO-ONE module is specifically designed for use with SUBARU Crosstrek Impreza and may not be compatible with other vehicles. Please check for compatibility before installation.

Vehicle functions supported in this diagram (functional if equipped)

COMPATIBLE
QR CODE
ON THE LABEL
MANUFACTURED AFTER: 2019

MODULE  COMPATIBLE REQUIS:
FIRMWARE VERSION

To add the firmware version and the options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool, sold separately.

Program bypass option:

IF THE VEHICLE IS NOT EQUIPPED WITH FUNCTIONAL HOOD PIN:
Program bypass option
(For RAP shutdown):

Parts required (Not included)
2X 1 AMP Diode

NOTES Make sure the key is not inside the car when remote starting.

MANDATORY INSTALL
HOOD PIN

HOOD STATUS : THE HOOD PIN SWITCH (INCLUDED) A11
MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.

SECURITY STICKER

Included
Notice: the installation of safety elements are mandatory. The hood pin and the sticker are essential security elements and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

DESCRIPTION

AUTOMATIC TRANSMISSION WIRING CONNECTION

KEY BYPASS PROGRAMMING PROCEDURE 1/3

Keep the other OEM remotes away from the vehicle.
Minimum 3 meters (10 feet).

Press and hold the programming button:
Insert the 6-Pin Main connector.
The LEDs will alternate between BLUE, RED, YELLOW & BLUE/RED flashes.

Release the programming button when the LED is BLUE.
If the BLUE LED is not ON solid disconnect the 6-Pin Main connector and go back to step 1.

Insert the required remaining connectors.

Do not press the brake pedal. Press the START/STOP button twice to turn ON the ignition.

Press and release the programming button once (1x).
The BLUE LED will turn off.
The BLUE LED will flash rapidly.

Press the START/STOP button once to turn OFF the ignition.
The BLUE LED will turn ON solid.

Remove the battery from 1 OEM remote.
Keep the other OEM remotes away from the vehicle. Minimum 3 meters (10 feet).

Place the OEM remote (no battery) close to the front of START/STOP button as shown.

Press the footbrake pedal.

  • The vehicle ignition will turn ON.
  • The RED RED will turn ON.
  • The RED BLUE will turn OFF.

Release the pedal.

Press the START/STOP button once to turn OFF the ignition.

Place the OEM remote (no battery) close to the front of START/STOP button as shown.

Press the footbrake pedal.

  • The vehicle ignition will turn ON.
  • The YELLOW LED will turn ON.
  • The RED LED will turn OFF.

Release the pedal.

Press the START/STOP button once to turn OFF the ignition.

  • The RED and YELLOW LEDs will alternated.

Disconnect all connectors and after the 6-Pin (Main-Harness) or the 4-Pin Data-link connector.
4-pins (Data-Link).

OR
Microsoft Windows Computer with  Internet connection*

**Smartphone*** (Internet provider  charges may apply)

Use the tool:
FLASH LINK UPDATER or FLASH LINK MOBILE
to visit the DCryptor menu.
*Parts required (not included)

AFTER DCRYPTOR PROGRAMMING COMPLETED
Go back to the vehicle and reconnect the 6-Pin (Main-Harness) or the 4-pins (Data-Link) connector and after all the remaining connector.

The module is now programmed.The module is now programmed.

REMOTE STARTER  / ALARM  VERIFICATION
Test the remote starter. . Remote start the vehicle .
REMOTE STARTER PROGRAMMING PROCEDURE

REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.

REMOTE STARTER FUNCTIONALITY

All key must be All key must be

All doors must be closed.

Remote start the vehicle.

Unlock the doors with the remote-starter  remote.

Enter the vehicle with the SMART-KEY.

Press the brake  pedal.

The vehicle can now be put in to gear and  driven.

The engine will shutdown when a door is open if the vehicle is not Unlock.

Module label
Notice: Updated Firmware and Installation Guides
Updated firmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest firmware and download the latest installation guide(s) prior to the installation of this product.

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.
Copyright © 2006-2019, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING

TECH SUPPORT
Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.co
WEB UPDATE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

FORTIN User Manuals

Related Manuals