OpenVox VS-GWM501V Audio Gateway Board User Manual
- August 29, 2024
- OpenVox
Table of Contents
OpenVox VS-GWM501V Audio Gateway Board
Product Information
The VS-GWM501V Audio Gateway Board is designed to provide audio input and output capabilities for the user. It features indicator lights, reset key functionality, audio channels, and network configuration options.
Specifications:
- Data Version: R1.2.0
- Product Version: R1.2.0
Product Usage Instructions
Introduction to the Device Panel:
-
Chassis Schematic
The chassis schematic shows the module for Chassis VS-GW1202/1600/2120 Series. -
Board Schematic
The board schematic diagram provides details about the VS-GWM501V Board components and their functions.
Login:
To login to the gateway webpage, open IE and type http://IP in the address
bar. The default login credentials are:
- User name: admin
- Password: 1
Operational State:
-
Registration Status and Line Status
You can view user registration status and line status information in the Registration Status section. Turn on Auto Refresh for real-time updates. -
Network and Version Information
View network information and version details in the respective sections to monitor the status of the gateway.
Network Information Configuration
Modifying Local Static IPs and Configuring SIP Servers
In the Basic Settings/Network Settings section, you can modify the static
network address of the gateway and configure SIP servers for registration
service.
FAQ:
- Q: How do I reset the gateway to its default settings?
A: Long press the reset key for more than 10 seconds to restore the temporary IP address and reboot the gateway to its original configuration.
Announcement:
This manual is intended as an operating guide for the user only. No part or
all of the contents of this manual may be reproduced, excerpted, or
transmitted in any form without the written permission of the Company.
Introduction to the device panel
Chassis Schematic
Module for Chassis VS-GW1202/1600/2120 Series
Board Schematic
As shown in Figure 1-2-1, the meaning of each mark is as follows
- Indicator lights: there are three indicator lights from left to right: fault 1) Indicator lights: there are three indicator lights from left to right: fault light E, power light P, running light R; equipment after normal operation of the power light is always green, running indicator light is green flash, fault light to retain the temporary useless.
- Reset key: Press and hold for more than 10 seconds to reset the temporary IP address 10.20.30.1, and reset the original IP address after power off and reboot.
- V1 is the first audio channel, red is OUT for audio output, white is IN for audio input. v2 is the second channel.
- The W interface is defined as shown in Figure 1-2-2
Login
Login to the gateway webpage: Open IE and type http://IP, (172.16.80.X（X is
the slot number of the chassis; If it is slot 3 of UCP1600, the IP address is
172.16.80.3.）), enter the login interface shown in Figure 1-1-1 below. Initial
user name: admin, password: 1
Long press reset for more than 10 seconds to restore temporary IP address
10.20.30.1, and restore original IP after power off and reboot.
Operational state
Registration Status and Line Status
In [Registration Status], you can view the user registration status and
line status information, turn on the Auto Refresh button to see the real-time
status, as shown in Figure 3-1-1:
Network and version information
In [Network Information] and [Version Information], you can view the
corresponding status information, as shown in Figure 7-2-1:
Network Information Configuration
Modifying local static IPs and configuring SIP servers
In [Basic Settings/Network Settings], you can modify the static network
address of the gateway, note that you need to open the Edit button to modify
it, and the SIP server can set the IP address, port, etc. of the primary and
backup servers for the registration service and the primary and backup
registration methods, as shown in Figure 4-1-1.
Clarification
Currently, the gateway IP acquisition method only supports static, and after
modifying the network address information, you need to reboot the device to
take effect.
Modify user number
The user number, registration period, hotline number, etc. of the gateway
can be modified in [Basic Settings/Channel Settings], as shown in Figure
4-2-1:
Click “Edit” to modify the user number information, as shown in Figure 4-2-1:
- Channel number: 0, 1
- Subscriber number: The telephone number corresponding to the line.
- Authentication ID, registration password, registration period: the account number, password and the interval between each registration used when registering with the platform.
- Hotline number: not valid in the audio gateway
- Carrier Level: Invalid in Audio Gateway
Advanced Settings
Call Settings and Gain Media Settings
In [Advanced Settings], first turn off the PTT mode switch as shown in
Figure 5-1-1:
In [Gain and Media Configuration], you can configure the user’s gain type, gateway to radio gain is one level to five levels, the default five levels maximum. Radio to Gateway using the default value cannot be configured, media support G.711A/U, as shown in Figure 5-1-1:
-
PTT Mode: PTT mode on for trunking, off for audio, audio gateway configured for PTT mode off
Call and SIP settings:- Maximum time without voice packs: 300 seconds without voice packs (mute packs are also considered voice packs) will automatically release the timer.
- No voice packet processing for a long time: release the call and do not process two ways, release the call to protect abnormal release the call with the
- Busy tone duration: Default 0, hang up and release release
- Initiate RPORT: This function is for network penetration purposes when registering to the public network.
Device Operation
Reboot, factory, firmware, packet capture and data file operations
In [Device Operation], as shown in Figure 6-1-1:
- Reboot operation: soft reboot the device.
- Factory Operation: Restore the factory settings of the device.
- Firmware operation: local upgrade, online firmware retention is useless for now. Packet grabbing operation: You can set the time for grabbing packets, and then it must be stopped automatically before you can download it.
- Data file operations: You can import and export database files.
Logging and logging operations
- Log operation: the higher the level the more detailed the print
personalized operation
- Personalized Device: You can change the name of the gateway in the upper left corner, such as “Wireless Trunk Gateway” in the picture.
- Language display: can switch between Chinese and English Color scheme: you can switch the skin color.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>