Queclink Wireless Solutions ZK611MG T-PANEL211 IoT Device User Manual
- June 6, 2024
- Queclink Wireless Solutions
Table of Contents
Queclink Wireless Solutions ZK611MG T-PANEL211 IoT Device User Manual
Introduction
ZK611MG (T-Panel211) software function development mainly involves electric control unit (ECU), @Track Air Protocol, instrument display, headlight control, acceleration, brake, key on panel, voice broadcast and Bluetooth. ZK611MG (T-Panel211) is designed to connect to the scooter to enable remotely lock/unlock, to track the position information and to report the status of the scooter. By using the accelerator or brake, the user can increase or decrease the speed of the scooter. By using the key on the panel, the user can turn on the headlight, switchover the speed-up mode or end using the scooter. All the information will be reported to the backend sever to facilitate the basic functions of the scooter.
ZK611MG (T-Panel211) Product
Model No.| Region| Technology| LTE Category|
Operating Band
---|---|---|---|---
T-Panel211|
Global G
|
GSM/LTE
|
eMTC/NB-IoT
| Cat M1/Cat NB2:
Cat M1: B1/B2/B3/B4/B5/B8/B12/B13/B18/B 19/B20/B25/B26/B27/B28/B66/B85
Cat M1 Power: 25 dBm
Cat NB2: B1/B2/B3/B4/B5/B8/B12/B13/B18/B 19/B20/B25/B28/B66/B71/B85 Cat
NB2 Power: 25 dBm EGPRS: 900(32.47dBm) /1800(30.17dBm)
T-Panel211M
T -Panel211MG
Product Overview
- Appearance
Hardware
Interface Definition
The power cable input, red wire for positive, black wire for negative.
Pin Name
| Description
---|---
GND
|
Power GND (Black)
UART_RX
|
The RX communication pin
UART_TX
|
The TX communication pin
Power_EN
|
To control the power supply
DC IN
|
Power+ Input (Red)
Getting Started
-
Installing SIM Card
-
Turn off ZK601MG (T-Panel201).
-
Open ZK601MG (T-Panel201) and insert SMI card as follows.
-
Communicating with Backend Server
After installing SIM card and power on, ZK601MG (T-Panel201) can communicate with the backend server through network, and transfer reports of emergency, Geo‐fencing, device status and scheduled GPS position etc. It is easy for service provider to set up their tracking platform based on the functional wireless tracking protocol.
FCC Regulations
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.
RF Exposure Information
This device meets the government’s requirements for exposure to radio waves.
This device is designed and manufactured not to exceed the emission limits for
exposure to radio frequency (RF) energy set by the Federal Communications
Commission of the U.S. Government.
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
FCC radio frequency exposure limits, human proximity to the antenna shall not
be less than 20cm (8 inches) during normal operation.
ISED Notice
This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
ISED RF Exposure Statement
This device complies with ISED RSS-102 RF exposure limits set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
IC RSS-102 RF exposure limits, human proximity to the antenna shall not be
less than 20cm (8 inches) during normal operation.
CE Declaration
Hereby, Queclink Wireless Solutions Co., Ltd. declares that the radio
equipment type GPS tracker is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address:
www.queclink.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>