SALTO W Series Handle Access Control Instructions
- August 17, 2024
- SALTO
Table of Contents
SALTO W Series Handle Access Control
Product Specifications
- Product: RFID Reader
- Commercial Name: XS4 Original, XS4 One S, XS4One S KEYPAD, XS4 Original i-Button
- Model: E0102 (A), E1215 (A), E2131 (A), E0127 (B)
- Technology: RFID 13.56 MHz
- Output max. Power: +25 dBm
- Control: Bluetooth LE Module, RF2 Module, SoC
- Mechanical Warnings: Avoid removing the protective layer; clean product surfaces with a damp cloth after manipulation; clean stainless steel regularly
Product Usage Instructions
Electrical Warnings
Caution: Distance between this device and human body must be higher than 20 cm.
Recommended Batteries
- Duracell Plus Power (AAA) LR03 MN2400
- Duracell Ultra Power (AAA) LR03 MX2400
- Varta Industrial (AAA) LR03 04003
- Varta High Energy (AAA) LR03 04903
- Varta Max Tech (AAA) LR03 MN2400
- Duracell Plus Power (AA) LR6 MN1500
- Duracell Ultra Power (AA) LR6 MX1500
- Varta Industrial (AA) LR6 04006
- Varta High Energy (AA) LR6 04906
- Varta Max Tech (AA) LR6 MN1500
Mechanical Warnings
- Avoid removing the protective layer. Clean product surfaces with a damp cloth after manipulation when the installation is finished. For best performance, stainless steel should be cleaned regularly.
- Note that when the door is closed without the lock having been already programmed, the lock will automatically lock and can onlybe opened with a Portable Programming Device (PPD).
- If you have questions or doubts, please contact your authorized SALTO supplier.
Frequently Asked Questions (FAQ)
-
Q: Can the RFID Reader work with any type of door?
A: The RFID Reader is compatible with most standard doors. It is recommended to consult with a SALTO supplier for specific door compatibility. -
Q: How often should the product surfaces be cleaned?
A: It is recommended to clean the product surfaces with a damp cloth after manipulation and to regularly clean stainless steel for best performance. -
Q: What should I do if the lock automatically locks without being programmed?
A: If the lock automatically locks without being programmed, it can only be opened with a Portable Programming Device (PPD).Contact your authorized SALTO supplier for assistance.
Compliance
PRODUCTS DESCRIPTION
| PRODUCT | TECHNOLOGY | SOFTWARE |
|---|
COMMERCIAL NAME
| ****
MODEL
| ****
RFID 13.56 MHz
Output max. Power
| ****
BLUETOOTH LE 2400–2483.5 MHz
Output max. Power
| ****
IEEE802.15.4 2400–2483.5 MHz
Output max. Power
| ****
CONTROL
| ****
READER
| ****
Bluetooth LE MODULE
| ****
RF2
MODULE
| ****
MOTOR
| SoC| ****
HSE
FUS
| Bluetooth LE
Stack
XS4 Original E0102 (A)
| W09| +25 dBm| | | 0037| 0132| | | | | |
W0J| +25 dBm| +8 dBm| | 0037| 0133| 0136| | | | |
W0S| +25 dBm| +2.8 dBm| | 0126| 0132| –| | | | |
W09W| +25 dBm| | +5 dBm| 0016/0061/0095| 0132| | 0038/0099| | | |
W0BW| +25 dBm| +8 dBm| +5 dBm| 0016/0095| 0132/0140| 0136| 0038/0099| | | |
W0JW| +25 dBm| +8 dBm| +5 dBm| 0016| 0133| 0136| 0038| | | |
W08| +20 dBm| | | 0037| 0082| | | | | |
W08W| +20 dBm| | +5 dBm| 0016/0061| 0082| | 0038| | | |
XS4 Original with Keypad
E1215 (A)
| W0BK| +25 dBm| +8 dBm| | 0016/0095| 0132| 0136| | | | |
W0JK| +25 dBm| +8 dBm| | 0016| 0133| 0136| | | | |
W0SK| +25 dBm| +2.8 dBm| | 126| 0132| –| | | | |
W0BWK| +25 dBm| +8 dBm| +5 dBm| 0016/0095| 0132/0140| 0136| 0038/0099| | | |
W0JWK| +25 dBm| +8 dBm| +5 dBm| 0016| 0133| 0136| 0038| | | |
XS4 Original+ E2131 (A)
| W40M| +25 dBm| +6 dBm| | 0174| | | | 0202| 0186| 0187| 0197
W40T| +25 dBm| +6 dBm| | 0174| | | | 0219| 0186| 0187| 0197
W40MH| +25 dBm| +6 dBm| | 0174| | | | 0219| 0186| 0187| 0197
W80M| +25 dBm| +6 dBm| | 0174| | | | 0202| 0186| 0187| 0197
W60M| +25 dBm| +6 dBm| | 0174| | | | 0202| 0186| 0187| 0197
W60T| +25 dBm| +6 dBm| | 0174| | | | 0219| 0186| 0187| 0197
W60MH| +25 dBm| +6 dBm| | 0174| | | | 0219| 0186| 0187| 0197
XS4 One S E2131 (A)
| W80M| +25 dBm| +6 dBm| | 0174| | | | 0202| 0186| 0187| 0197
W40T| +25 dBm| +6 dBm| | 0174| | | | 0219| 0186| 0187| 0197
W40MH| +25 dBm| +6 dBm| | 0174| | | | 0219| 0186| 0187| 0197
W60M| +25 dBm| +6 dBm| | 0174| | | | 0202| 0186| 0187| 0197
W60T| +25 dBm| +6 dBm| | 0174| | | | 0219| 0186| 0187| 0197
W60MH| +25 dBm| +6 dBm| | 0174| | | | 0219| 0186| 0187| 0197
XS4 One S KEYPAD
E2131 (A)
| ****
W61MK
| ****
+22 dBm
| ****
+6 dBm
| | ****
0190
| | | | ****
0202
| ****
0186
| ****
0187
| ****
0197
XS4 Original i-Button E0127 (B)| W02| | | | 0023/0024/0025| | | | | | |
EU DECLARATION OF CONFORMITY
EN Hereby, SALTO Systems S.L. (Arkotz Kalea (Pol. Lanbarren), 9 – 20180
Oiartzun– Spain), declares that this access control equipment is in compliance
with the essential requirements and other relevant provisions of Directive
2014/53/EU (RED) and 2011/65/EU (RoHS). You will be able to find a copy of the
original declaration of conformity at the following Internet address:
https://www.saltosystems.com/certificate
UKCA DECLARATION OF CONFORMITY
Hereby, SALTO Systems S.L. (Arkotz Kalea (Pol. Lanbarren), 9 – 20180 Oiartzun–
Spain), declares that this access control equipment is in compliance with the
essential requirements and other relevant provisions of The Radio Equipment
Regulations 2017 and RoHS Regulation 2012. You will be able to find a copy of
the original declaration of conformity at the following Internet address:
https://www.saltosystems.com/certificate
UK importer contact information:
Salto Systems, Ltd. Unit 1, The Court Holywell Business Park, Northfield Road,
CV47 0FS Southam, UK.
EU DECLARATION OF CONFORMITY
EN Hereby, SALTO Systems S.L. (Arkotz Kalea (Pol. Lanbarren), 9 – 20180
Oiartzun– Spain), declares that this access control equipment is in compliance
with the essential requirements and other relevant provisions of Directive
2014/30/EU (EMCD), 2014/35/EU (LVD) and 2011/65/EU (RoHS). You will be able to
find a copy of the original declaration of conformity at the following
Internet address: https://www.saltosystems.com/certificate
UKCA DECLARATION OF CONFORMITY
Hereby, SALTO Systems S.L. (Arkotz Kalea (Pol. Lanbarren), 9 – 20180 Oiartzun–
Spain), declares that this access control equipment is in compliance with the
essential requirements and other relevant provisions of The Electromagnetic
Compatibility Regulations 2016, The Electrical Equipment (Safety) Regulations
2016 and RoHS Regulation 2012. You will be able to find a copy of the original
declaration of conformity at the following Internet address:
https://www.saltosystems.com/certificate
UK importer contact information:
Salto Systems, Ltd. Unit 1, The Court Holywell Business Park, Northfield Road,
CV47 0FS Southam, UK.
ELECTRICAL WARNINGS
Caution
- Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
- Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, can result in an explosion.
- Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas.
- A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
Recommended batteries
-
Duracell Plus Power (AAA) LR03 MN2400
-
Duracell Ultra Power (AAA) LR03 MX2400
-
Varta Industrial (AAA) LR03 04003
-
Varta High Energy (AAA) LR03 04903
-
Varta Max Tech (AAA) LR03 MN2400
-
Duracell Plus Power (AA) LR6 MN1500
-
Duracell Ultra Power (AA) LR6 MX1500
-
Varta Industrial (AA) LR6 04006
-
Varta High Energy (AA) LR6 04906
-
Varta Max Tech (AA) LR6 MN1500
MECHANICAL WA RNINGS
In order to confirm the correct operation of this electronic device, SALTO
recommends using it in combination with a lock destined for that use (door
mass, frequency of use, fire door, etc.) and that is in good operational
conditions. Polished finishes are strongly recommended in seaside environments
for a better performance and durability. The environmental conditions
mentioned in the data sheets are always referred to non-condensation
situations. The Biocote and IA finishes are painted and sharp objects such as
rings or metallic key rings or other metallic objects should be avoided during
any cleaning process. The SALTO product should be treated with care during the
installation process to avoid any aggressive contact that may damage the unit.
It may be necessary to loosen the trims mounting during installation. Do not
bring the device into contact with oil, paints or acids. Do not paint the door
with the mortise lock or electronic device already mounted on the door.
CLEANING THE ELECTRONIC DEVICE: a damp cloth with mild soapy water can be
used. Never use abrasive soaps or sprays. The black chromium finish (“NE”
code) is coated with a protective oil that improves the product conservation.
Its presence may increase the appearance of fingerprint traces after the
needed product handling. Thus, no cleaning processes are applied at the origin
to avoid removing the protective layer. SALTO recommends cleaning the product
surfaces with a damp cloth after its manipulation when the installation is
finished. For best performance, stainless steel should be cleaned regularly.
Note that when the door is closed without the lock having been already
programmed, the lock will automatically lock and can only be opened with a
Portable Programing Device (PPD). If you have questions or doubts on this,
please contact your authorized SALTO supplier.
LEGAL WARNINGS
The user shall be responsible for the correct use and maintenance of the
access control equipment according to the instructions herein. SALTO shall not
be responsible for any defect, malfunction, loss or damage, whether direct or
indirect, caused by or arisen from any improper installation or utilization of
the equipment or which contravenes, transgresses or infringes in any manner
the above mentioned instructions. SALTO’s liability concerning the equipment
is limited to the warranty provided. The warranty does not cover product
failures due to repairs, modifications or product manipulations performed in
the access control equipment or in the inner electromechanical structure by
anyone other than authorized SALTO dealers or personnel.
FCC COMPLIANCE STATEMENT [1]
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This product is a radio transmitter and receiver to be used in mobile conditions.
Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information
We, SALTO Systems, S.L., hereby declare that the equipment bearing the model
number specified above was tested conforming to the applicable FCC Rules.
Responsible Party – U.S. Contact Information
Salto Systems Inc. USA. 1780 Corporate Drive, Suite 400. Norcross, GA. 30093.
v.kourelos@saltosystems.com
ISED COMPLIANCE STATEMENT [2]
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. Changes
or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device has been tested and found to comply with the limits for a Class B
digital device, pursuant to ICES-003.
IMDA COMPLIANCE LABEL [4]
Complies with IMDA Standards DA108623
NCC WARNING STATEMENT / NCC[5]
Legend:
| Remarks:
---|---
[1] FCC| Not applicable for models W08, W08W
[2] ISED| Not applicable for models W08, W08W
[3] MIC| Not applicable for models W08, W08W, W40M, W60M, W80M, W41M,
W61M, W81M, W61MK, W02
[4] IMDA| Not applicable for models W08, W08W, W02
[5] NCC| Not applicable for models W09, W0S, W09W, W0BW, W0JW, W08,
W08W, W0SK, W0BWK, W0JWK, W40M, W60M, W80M, W41M, W61M, W81M, W61MK, W02
SALTO SYSTEMS S.L. www.saltosystems.com
3/3
Pol. Lanbarren, c/Arkotz nº9, 20180 Oiartzun, Spain.
All contents current at time of publication. SALTO Systems S.L. reserves the
right to change availability of any item in this catalog, its design,
construction, and/or materials.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>