SALTO LE7S15 Asymmetric Mortise Lock Installation Guide

SALTO LE7S15 Asymmetric Mortise Lock

Product Specifications

• Product Name: SALTO LE7Sxx Asymmetric Mortise Lock
• Manufactured according to DIN 185251
• Available Hand Codes: 21, 55, 60, 65, 70
• Door Opening: Right Hand (R) Inward opening, Left Hand (L) Inward opening
• Reverse Options: R=LR, L=RR, Right Reverse (RR), Left Reverse (LR)
• Lock Types: LE7S05 Mechanical lock for escape routes and/or fire doors, LE7S15 Mechanical lock for escape routes and/or fire doors with panic function, LE7S25 Mechanical lock for fire doors
• Certifications: CERTIFIED CF 5596, ES 5454/2020, EN 12209:2003 + AC:2005, EN 179:2008

Product Usage Instructions

1. Remove the screws and the front plate.
2. Fix the front plate with the screws.
3. Push the latch forward from the back of the lock using a screwdriver.
4. In case there is no cylinder retaining screw, install the cylinder retaining screw cover.
5. If there is no external lever, insert the hub protector on the outside part of the door for models without contacts.

For Wood Rebate Door

• Minimum Thickness: 20mm
• Dust box included

For Metal Rebated Door

• Minimum Thickness: 19mm

FAQ

• Q: What are the available handcodes for this lock?
• A : The available hand codes are 21, 55, 60, 65, and 70.
• Q: How do I change the hand orientation of the lock?A: To change the hand orientation, follow the steps provided inthe installation guide. Ensure to use the correct reverse optionsbased on your door configuration.
• Q : What certifications does this lock have?
• A: This lock is certified with CERTIFIRE CF 5596, ES 5454/2020, EN 12209:2003 + AC:2005, and EN 179:2008 standards.

Dimension

Asymmetric

• Manufactured according to DIN 185251

SALTO hand code

• Door type according to EN179 cat. B
• Door type according to EN179 cat. D

Hand changing

Please follow the drawing

1. Remove the screws and the front plate.
2. Turn the front plate 180º as it is shown in the drawing.
3. Fix the front plate with the screws.
4. Push the latch forward from the back of the lock with a screwdriver until it completely comes out from the front, then turn 180º.
5. Pull the auxiliary latch forward and turn it 180º.

Installation

Lock installation

PREPARING THE DOOR
NOTE: if the strike already exists in the door frame, position the latch using the strike as a reference.(See strike position on template)

1. Draw a horizontal line on both sides and edge of the door at the desired height of the handle above floor.
2. Draw a vertical centre line on the door edge.
3. Draw a vertical line on each side of the door at the proper backset to align the template.
4. Position templates on the edge and sides of the door. Mark only the top and bottom holes of the mortise cavity (A) and lock front (B) on door edge, and holes in the lateral face of the door for handles (C) and cylinder (D) (only needed in inside face).
5. Remove the template. Make door preparation of the lockcase according to (A).
6. Insert the lockcase. Draw the outline using the face plate as a template for door preparation.

NOTE: Holes for fixation of SALTO electronic escutcheon are not included in this template. Please use the template in the escutcheon box.
INSTALLING THE LOCK

1. Insert the lock into the cavity.
2. Mark & drill faceplate holes. Fasten with faceplate screws to hold the lock in place.

INSTALLING THE STRIKE

1. Refer to the latch to determine the strike location on the jamb.
2. Using strike as template, mark and chisel recess. Drill screw holes. Place the dust box and strike and fasten it with the supplied screws.
3. Please check if:
4. The deadbolt and latch fit the cavities of the strike without touching it.
5. The gap between the door and jamb is between 2-4 mm.
6. The strike flap should protrude at least 2mm, if it does not, please ask your distributor for the availability of special strikes.

CABLE CONNECTION
For models with detectors, connect according to the corresponding electronic escutcheon installation guide.

Strike installation

Wood rebated door

Metal rebated door

Maintenance

All locks come from the factory pre-lubricated with grease. We recommend, however, continued periodic lubrication of moving parts like the latch, auxiliary latch and deadbolt, with commercial-quality grease (every 20.000 cycles or once a year). This can prolong the life o the lockset by reducing excessive wear. If the lockset is used in a harsh environment, lubrication should be applied more frequently

FEATURED

• The safety features of this product are essential to its compliance with EN 179. No modification of any kind, other than those described in these instructions, is permitted.
• This device is intended for use on single inward/outward opening fire and non-fire-rated escape route doors.
• This product is to be used on doors with maximum dimensions of 1300mm wide x 2500mm high and weighing no more than 200kg (440lb).
• Maximum door distortion of 5mm allowed to ensure safe exit at all times.
• Maximum of 1000N abuse force achieved under the abuse test.
• Category of Projection = Category 1 Less than 150mm (“I” handle).
• For use on timber doors.
• Suitable for use on fire doors.
• Fire resistance 30 mins, 60 mins and 90 mins timber doors.
• For fire certificates, see www.saltosystems.com
• This product meets EN 179 only when combined with an XS4 Original, XS4 Original+, XS4 One or XS4 One+ electronic escutcheon fitted with U, H or J handles, or XS4 Mini electronic escutcheon fitted with U, E, I or J handles.
• Blocking the electronic lever handle from the outside can render the device inoperable from the inside.

All contents are current at the time of publication. SALTO Systems S.L. reserves the right to change the availability of any item in this catalogue, its design, construction, and/or materials

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>