SALTO XB090380 Mifare NBE1130N00CSBD Neo Euro Cylinder Single Installation Guide
- June 4, 2024
- SALTO
Table of Contents
SALTO XB090380 Mifare NBE1130N00CSBD Neo Euro Cylinder Single Installation
Guide
INSTRUCTION
-
SALTO Recommended Batteries SP01926-5
-
PH2 (x1)
Danger for electronic components due to electrostatic discharge.
www.saltosystems.com/en/quick-links/manuals-and-
guides/
Installation
AT THIS POINT DO NOT CLOSE THE DOOR PROGRAM THE CYLINDER FIRST
Installation
AT THIS POINT DO NOT CLOSE THE DOOR PROGRAM THE CYLINDER FIRST
Battery change
DRY!
Installation and use recommendations
**Outer knob
**
**Do not place any movable metallic object closer than 5cm in front of the reader.
**
The knob is uniquely paired to the cylinder, and will not work if you switch in a different SALTO cylinder
Compliance
PRODUCTS DESCRIPTION
| PRODUCT | TECHNOLOGY | SOFTWARE |
|---|---|---|
| COMMERCIAL NAME | MODEL | **RFID |
13.56MHz
Output max. power| BLUETOOTH SMART 2400–2483.5 MHz
Output max. power| CONTROL CIRCUIT| MOTOR CIRCUIT| BLUETOOTH
MODULE| SoC
FUS| BLE Stack**
SALTO Neo G1824| N0B| +24 dBm| +8 dBm| 0180| 0148| 0184| |
N0M| +24 dBm| +6 dBm| 0195| 0148| | 0186| 0187
N0J| +24 dBm| +8 dBm| 0159| 0148| 0136| |
EU DECLARATION OF CONFORMITY
Hereby, SALTO Systems S.L. (Arkotz Kalea (Pol. Lanbarren), 9 – 20180 Oiartzun– Spain), declares that this access control equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU (RED) and 2011/65/EU (RoHS). You will be able to find a copy of the original declaration of conformity at the following Internet address: https://www.saltosystems.com/certificate
ELECTRICAL WARNINGS
Caution:
- Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
- Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, can result in an explosion.
- Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas.
- A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.
Distance between this device and human body must be higher than 20 cm.
Recommended batteries
ENERGIVM **(N) LR1 (SALTO Ref:SP01926-5)
**
Note: SALTO does not guarantee the life of the battery if another brand is used.
MECHANICAL WARNINGS
In order to confirm the correct operation of this electronic device, SALTO
recommends using it in combination with a lock destined for that use (door
mass, frequency of use, fire door, etc) and that is in good operational
conditions. Only water resistant model can be installed outdoor. Polished
finishes are strongly recommended in seaside environments for a better
performance and durability. The environmental conditions mentioned in the data
sheets are always referred to non-condensation situations. The Biocote finish
is painted and sharp objects such as rings or metallic key rings or other
metallic objects
should be avoided during any cleaning process. The SALTO product should be
treated with care during the installation process to avoid any aggressive
contact that may damage the unit. It may be necessary to loosen the trims
mounting during installation. Do not bring the device into contact with oil,
paints or acids. Do not paint the door with the mortise lock or electronic
device already mounted on the door. CLEANING THE ELECTRONIC DEVICE: a damp
cloth with mild soapy water can be used. Never use abrasive soaps or sprays.
For best performance, stainless steel should be cleaned regularly. Note that
when the door is closed without the lock having been already programmed, the
lock will automatically lock and can only be opened with a Portable Programing
Device (PPD). If you have questions or doubts on this, please contact your
authorized SALTO supplier.
LEGAL WARNINGS
The user shall be responsible for the correct use and maintenance of the
access control equipment according to the instructions herein. SALTO shall not
be responsible for any defect, malfunction, loss or damage, whether direct or
indirect, caused by or arisen from any improper installation or utilization of
the equipment or which contravenes, transgresses or infringes in any manner
the above mentioned instructions. SALTO’s liability concerning the equipment
is limited to the warranty provided. The warranty does not cover product
failures due to repairs, modifications or product manipulations performed in
the access control equipment or in the inner electromechanical structure by
anyone other than authorized SALTO dealers or personnel.
FCC COMPLIANCE STATEMENT (1)
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This product is a radio transmitter and receiver to be used in mobile conditions.
Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information
We, SALTO Systems, S.L., hereby declare that the equipment bearing the model
number specified above was tested conforming to the applicable FCC Rules.
Responsible Party – U.S. Contact Information Salto Systems Inc. USA. 1780
Corporate Drive, Suite 400. Norcross, GA. 30093.
n.buffington@saltosystems.com
ISED COMPLIANCE STATEMENT (2)
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IMDA COMPLIANCE LABEL (3)
NCC WARNING STATEMENT / NCC 4
Legend
| Remarks: | |
|---|---|
| (1) FCC | — |
| (2) ISED | — |
| (3) IMDA | Not applicable for N0M |
| (4) NCC | Not applicable for N0M |
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>