NINGBO CLOCK-6228 Oval Desk Lamp User Manual

NINGBO CLOCK-6228 Oval Desk Lamp

Specifications

• Size: 256×230.1×77.3mm/10.08×9.06×3.04”
• Weight: 396g/0.79lbs
• Light source: 20pcs 5050
• Input: 5V, 2A
  • w bluetooth speaker
  • w USB-C cable: 80cm/31.5”
• Plug in an adapter or connect the USB to a 5V 2A output for power

How to connect the bluetooth

• For the first-time connection, make sure the Bluetooth of your phone is on, find the device named “BH Speaker Charging Lamp” and connect to it.
• There will be a sound indicator when the Bluetooth is connected.

Wireless charging:
Put the phone onto the desk lamp, the phone will wirelessly charge. When you pick up the phone from the desk lamp, charging will be stopped.

Function for buttons

Button Bluetooth
Short press into bluetooth mode, connect to bluetooth successfully, and the clock will be set automatically short press again, to turn off the bluetooth

Button “CLOCK” and “SET”: To set time and alarm clock(AL).
Long press button “CLOCK” into AL mode to set hours when the hour (2 digits on the left) flash, then short press “SET” 2 digits cycle from AM 1-2…-11, PM12-1-…11-AM12, select the hour you need, Short press “CLOCK” again, the minute(2 digits on the right) flash, short press “SET” to set minute for AL, 2 digits cycle from 00-…59-00;

Remark: Short press to increase 1 hour or 1 minute, long press to adjust hours and minutes rapidly.

Turn alarm clock(AL) ON/OFF
short press “CLOCK”, AL light and on, the alarm clock will ring when reaching alarm time, short press again, AL light oand ff, the alarm clock will not ring when to reach alarm time.

When the alarm ring, short press “CLOCK” to turn off the alarm.

• Button”LIGHT”: Long press “LIGHT” to turn on the light
• Short press “LIGHT”: RGB color select (3 solid colors and 4 cycle modes )
• Long press “LIGHT”: turn off the light(Memory feature: the last light setting will be saved. For example: if the light was set in blue, the same setting will resume when you turn the unit back on. )

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution:

• Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co‐located or operating in conjunction with any other antenna or transmitter.

This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

Frequently Asked Questions

• Q: How do I reset the Bluetooth connection?
  • A: To reset the Bluetooth connection, turn off the lamp, turn it back on, and follow the initial connection steps as mentioned in the user manual.
• Q: Can I use any USB adapter for powering the lamp?
  • A: It is recommended to use an adapter that outputs 5V, 2A for optimal performance. Using a different adapter may affect functionality.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>